RS-855lcd PROFESSIONAL REMOTE CAR STARTER WITH ALARM SYSTEM & 2-WAY LCD COMMUNICATION OPERATION MANUAL THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY 1
TABLE OF CONTENTS: A. REMOTE TRANSMITTER OPERATION …………………….………. 4 B. BUTTON LOCK ……………………………………………….……...…. 5 C. LED DISPLAY .……………..……..……………………….……………. 5 D. CHIRP INDICATOR ..………..………..……………………………..…. 5 E. PARKING LIGHT ………..………………………………………..….…. 6 F. ALARM OPERATION CONDITION .…..…………………………...…. 6 G. ACTIVE ARMING – ARM & LOCK .……..……………...……………. 6 Defective Sensor Reminder Silent Arming / Disarming Shock Sensor By-Pass H. PASSIVE ARMING .………………………………………….………….
REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE ………..…………..…………. 14 Safe Start (Child safety mode) B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START……………………………………………………………………14 C. TEMPORARY STOP FEATURE …………………..………...….…… 14 D. TURBO TIMER START FEATURE ……………………………………15 D. TIMER / TEMPERATURE START ……………….………..………… 15 3 Hours Timer Start With Temperature-Control Off 3 Hours Timer Start With Temperature-Control Daily Timer Start Exit the Timer Start E. TEMPERATURE CHECK …………………….….……….…….….
As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out o f children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5. Always apply the parking brake and lock the vehicle as you exit the vehicle. 6.
Channel # 5 Timer Output (5) + Channel # 6 Timer Output (6) + LCD DISPLAY TRANSMITTER OPERATION ONLY: Transmitter Button - (C) - - System Function System’s Trigger Record Check Remark System’s Status Check Press within 3 seconds Button Lock Press within 3 seconds and Hold Optional Driving Pager Press within 3 seconds Monitor Indoor Temperature Press within 3 seconds Daily Timer Start Press within 3 seconds Press within 3 seconds (C) - ( ) button for 2 seconds - ( ) - ( ) - (
Flash Flash Passive Starter Disable Fast Flash Passive Arming On (Solid) Valet Mode pause 3 flashes... pause 4 flashes... pause 5 flashes... pause D. CHIRP INDICATORS: Chirp Function 1 chirp Arm 2 chirps Disarm 3 chirps Defective Reminder 4 chirps Disarm / Triggered 6 chirps Car Locator Zone 3 / Trigger on Door Switch Zone 4 / Trigger on Shock Sensor Zone 5 / Trigger on Ignition Switch E.
SILENT ARMING / DISARMING: Press the transmitter and button at the same time will arm or disarm your security system, No chi rp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only. SHOCK SENSOR BY-PASS: Press the button on the transmitter two times within 3 seconds will arm the security system and by-pass the shock sensor. The system will chirp one additional time to confirm the sensor bypass mode was activated.
System Disarm Shock SensorTrgr Doors Trigger Ignition Trunk/HoodTrgr Warn away Trigger Trigger Clear The Flash Icon: Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transmitter. TAMPER DISARMING: If alarm is triggered upon disarm, the systems siren will chirp 4 times, and parking light flash 3 times. PATHWAY ILLUMINATION: This feature turns the parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal.
4. Within 15 seconds, enter your chosen of the second digit code by pressing and releasing the Valet Switch. 5. Turn the ignition switch “OFF” position. 4] Chirps form siren/horn, [3] flash from parking light to indicate the system was disarmed. Note 1: You must override the alarm within 60 seconds. If not, the system will automatically re-arm. EXAMPLE: To Override The System With The Password Code 83, 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2.
1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter and buttons can be used to lock and unlock the door (if the option is installed), however once the button is pressed, the vehicle’s starter disable device, (where installed) will be disengaged allowing the vehicle to start. 3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3 seconds.
Ignition Trigger CLEAR THE FLASH ICON AND MELODY SOUND: While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon, press the button 3 times within 3 seconds will clear the flash icon and stop melody sound on the LCD screen transmitter.
TRIGGER THE ANTI CAR -JACKING MODE: 3-timer circuits will function as follows: First timer: a. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds. b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the car-jacking feature. c. If not, it will enter second timer car jacking. Second timer: 65 seconds after the system has been triggered. The siren starts alarming and the parking light starts flashing.
melody sound continues sounding from you Remote LCD Transmitter and “ ” indication flashes on the LCD screen. 1. Press the transmitter button first, within 3 seconds press ( ) button to activate outdoor driver paging function , It responds with chirps of the vehicle, a melody sound and " " indication flashes on the LCD screen to confirm the function is on. 2.
Press the transmitter (5) and (5) buttons at the same time to active Channel 5 function. Channel 5 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power window or sunroof. (Factory defaults setting at momentary output.) X. CHANNEL 6 TIMER CONTROL OUTPUT Press the transmitter (6) and (6) buttons at the same time to active Channel 6 function.
1. Press first, within 3 seconds press and hold and buttons at the same time for 2 seconds . One long beeping sound and the “ ” timer icon will be displayed on the LCD screen indicating the system is back to the first transceiver pin code. 2. While the “ ” timer icon is displayed on the LCD screen, you can remote control and communicate with the first vehicle security system. It has one short “bi” soun d while pressing the button of the LCD screen transceiver. Y.
2. The user presses the transmitter start the vehicle. and buttons at the same time to B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START: To operate the vehicle while the engine is running on the remote start, 1. Insert the ignition key and turn it to “ON” (not the start) position. 2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. C.
or drops below the preprogrammed temperature level. The system will monitor the air temperature every 3 hour and will only start the engine during extreme cold temperatures. There are three temperature levels to choose from. Daily Timer Start: The feature is very useful for the driver who wants to run the vehicle punctually at the same time next morning. Before set-up of the “Daily Timer Start”, you should set you time for engine start.
If you installed the optional temperature sensor, you can monitor, through the LCD screen, the present indoor temperature of the passenger compartment before cooling or heating your vehicle. Press the transmitter buttons first, within 3 seconds press the ( ) button, the in-door temperature will be shown on the LCD screen. This reading may be higher than actual ambient temperature due to the greenhouse and is relative only the inside vehicle temperature. F.
LCD REMOTE CONTROL TRANSMITTER: Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency. A. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen.
B. THE REMOTE LCD ICONS WITH FUNCTION: Door Lock Your vehicle doors are locked Armed Mode Your vehicle is in armed mode Door Unlock Your vehicle doors are unlocked and the system is Disarmed Valet Mode All the function shall be temporarily on hold. Remote Transmission You are transmitting the signal to control unit Door Open Warning Doors are illegally opened (Zone 3) In – Range Indicator Your are within the remote control range.
Vibration Mode Remote Control vibrates when the system is triggered Driver paging Someone is paging you in front of your vehicle Button Lock Disable the transmission function temporarily Low Battery You have to replace the battery of remote control. E. PROGRAMMING OF THE LCD REMOTE TRANSMITTER: Transmitter Button (1 second) (3 seconds) (5 seconds) - - - - (2-second) (2-second) (2-second) Description LCD screen lamp turns on for 5 seconds. Timer Programming Mode.
Entry: 1. Press & hold the button for 5 seconds, with one melody sound and icon on the LCD screen to indicate entry the “power save mode”. 2. Under the “Active Arming Mode” and Disarm mode. Turn the ignition switch to on, the LCD remote transmitter will automatically entry the “Power Save Mode” Exit: Press any button of the LCD remote transmitter to exit the “Power Save Mode”. 3.
8. Low Battery Indication: When the power of the battery weakens, it has two short “bi” sound and flash icon while pressing the button of the LCD screen transmitter. 9. Set Up Fixed Count Down Timer: 1. Press the button first, within 3 seconds press and hold the button for 2 seconds, the LCD screen will shows ( ) icon and timer (i.e. 0:10), 2. Press the ( ) button again showing next order time on the screen (ie.0: 20), press them again (ie.0: 30)…and so on. 3.
Daily Timer Start Timer 4 Press & hold the button for 2 seconds. Setting Flash / icon and “Hours” for adjusting EXIT: Press and hold the the system will exit the programming mode. for – and for + button for 2 seconds or leave it for 10seconds, 1. Timer Setting: Example to AM10:30 1. Press & hold the button for 3 seconds, with two-melody sound and the “Hours” digit flashes for adjusting. 2. Press the AM10:xx or 3. Press the adjusting.
PM 6:xx 4. Press the adjusting. 5. Press the PM 6:30 button once again then the “Minutes” digit flashes for or button to decrease or increase the “Minutes” digit until 6. Press the OFF” setting button once again then icon flashes for alert alarm “ON / 7. Press the button to start the “Alert Alarm Timer”, and the “ON” icon will show on the LCD screen. Press the button to stop the “Alert Alarm Timer”, and the “OFF” icon will show on the LCD screen. 8.
3. Press the or until AM 6:00 4. Press the button to decrease or increase the hour digit button once again then the minute digit flashes. 5. Press the or until AM 6:30 button to decrease or increase the minutes digit 6. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode. LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. and Continental U.S. Only) 1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
3. The purchaser’s remedies under this WARRANTY shall be limited to the repair or replacement of electronic components only. THE FOLLOWING IS NOT COVERED: Damages or deterioration to cases, batteries, covers and cabinets; the cost of repairs, replacement and labor of which shall be borne by the purchaser even if occurring during the WARRANTY period. 4.
Serial # _______________ CUSTOMER TO COMPLETE DEALER TO COMPLETE Mr./Mrs./Ms.
1815 West 205th Street Suite 101 Torrance, California 90501-1525 Main Office: 310-618-2002 Customer Service: 800-262-2527 Ext. 462 www.autopageusa.
