RS-860lcd PROFESSIONAL REMOTE CAR STARTER WITH ALARM SYSTEM & 2-WAY LCD COMMUNICATION OPERATION MANUAL THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY 1
TABLE OF CONTENTS: LCD REMOTE TRANSMITTER: A. REMOTE TRANSMITTER OPERATION…………………………….…4 B. BATTERY REPLACEMENT ………………………………………..….. 5 C. THE REMOTE LCD ICONS WITH FUNCTION ……………..…...…....6 C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER ………...7 1. Screen Lamp ON 2. Power Save Mode 3. Clear The Flash Icon and Melody Sound 4. Stop The Melody Sound. 5. Button Lock 6. Vibration / Melody Mode 7. Enable / Disable Bi Sound While Pressing Button: 8. Low Battery Indication. 9. Set Up Fixed Count Down Timer 10.
N. TRIGGER THE SYSTEM ..……..………………..………….….……...17 Clear The Trigger Icons and Melody Sound Stop The Melody Sound Only Noise Abatement Circuit O. ANTI CAR- JACKING .………………………………………….……...18 Active Anti Car Jacking Passive Anti Car Jacking Trigger The Anti Car Jacking Mode Override The System To Turn Off Anti Car Jacking P. SYSTEM’S TRIGGER CHECK …………………….….….…..….…...19 Q. SYSTEM’S STATUS CHECK …………………..……….…….….…..19 R.DRIVER PAGING (OPTION)…………..…………………….………....19 S.
WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5. Always apply the parking brake and lock the vehicle as you exit the vehicle. 6.
A. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the icon shall be battery weakens a displayed on the LCD screen. When the old battery is replaced to new one, there will be beep sounds indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons. Correct the time by pressing for 3 seconds before using (See Timer Setting). B. BATTERY REPLACEMENT: Remove screw from back of XT-85s Transmitter.
B. THE REMOTE LCD ICONS WITH FUNCTION: Door Lock Your vehicle doors are locked Armed Mode Your vehicle is in armed mode Door Unlock Your vehicle doors are unlocked and the system is Disarmed Valet Mode All the function shall be temporarily on hold. Remote Transmission You are transmitting the signal to control unit Door Open Warning Doors are illegally opened (Zone 3) In – Range Indicator Your are within the remote control range.
C: PROGRAMMING OF THE LCD REMOTE TRANSMITTER: Transmitter Button (1 second) (3 seconds) (5 seconds) - - - (2-second) (2-second) (2-second) Description LCD screen lamp turns on for 5 seconds. Timer Programming Mode. Power Save Mode Clear the Flash Icon and Melody Sound on the LCD Screen Transmitter Press within 3 seconds Button Lock ( disable ) enable / ) Melody / Vibration ( Mode Program Count Down Timer ) (10-Minute / 20M / 30 ( M /1Hour /1.5H / 2.
5. Button Lock: It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others. button first, within 3 seconds press and hold the Press the ( ) button for 2 seconds to activate or cancel the button lock function, the icon will displayed on the LCD screen to show the LCD remote transmitter is on “Button Lock”. 6.
D. CLOCK & TIMER SETTING: 1 2 3 Transmitter Button Description Press & Hold the button until hour flashes Clock Setting (Hour) *Flash digit for adjusting Press the once button Time setting (Minute) *Flash digit for adjusting Press the once.
2. Alert Alarm Timer Setting: Example to PM 6:30 button for 3 seconds, with two-melody sound and the 1. Press & hold the “Hours” digit flashes for adjusting. 2. Press the button twice, the LCD screen will shows digit is flashing for adjustment. 3. Press the PM 6:xx or 4. Press the adjusting. 5. Press the PM 6:30 6. Press the OFF” setting 7.
4. Time Set-Up For “Daily Timer Start”: Example to AM 6:30 button for 3 seconds, with two-melody sound 1. Press & hold the and the “Hours” digit flashes for adjusting. 2. Press & hold the / button for 2 seconds, the LCD screen will flash icon and “Hours” digit for Hour set-up. or 3. Press the until AM 6:00 4. Press the button to decrease or increase the hour digit button once again then the minute digit flashes. 5.
LCD DISPLAY TRANSMITTER OPERATION ONLY: Transmitter Button - (C) - - System Function System’s Trigger Record Check Remark Press within 3 seconds System’s Status Check Press within 3 seconds Button Lock Press within 3 seconds and Hold (C) - ( - ) ( button for 2 seconds ) - ( ) - ( ) - - Optional Driving Pager Press within 3 seconds Monitor Indoor Temperature Press within 3 seconds Daily Timer Start Press within 3 seconds LCD screen lamp turns on for 5 seconds.
C. LED display: LED Off Function Disarmed LED Slow Flash Armed Flash Passive Starter Disable Fast Flash Passive Arming On (Solid) Valet Mode D. CHIRP INDICATORS: Chirp Function 1 chirp Arm 2 chirps Disarm 3 chirps Defective Reminder 4 chirps Disarm / Triggered 6 chirps Car Locator Function Zone 1 / Warn-Away Trigger 2 flashes... pause 3 flashes... pause 4 flashes... pause 5 flashes...
System Arm Trunk / Hood Ajar Door Ajar Clear The Flash Icon: button 3 Press the times within 3 seconds will clear the flash icon on the LCD screen transmitter. DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hoodlid ajar. SILENT ARMING / DISARMING: Press the transmitter and button at the same time will arm or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only.
System Disarm Shock SensorTrgr Doors Trigger Ignition Trunk/HoodTrgr Warn away Trigger Trigger Clear The Flash Icon: Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transmitter. TAMPER DISARMING: If alarm is triggered upon disarm, the systems siren will chirp 4 times, and parking light flash 3 times. PATHWAY ILLUMINATION: This feature turns the parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal.
4. Within 15 seconds, enter your chosen of the second digit code by pressing and releasing the Valet Switch. 5. Turn the ignition switch “OFF” position. 4] Chirps form siren/horn, [3] flash from parking light to indicate the system was disarmed. Note 1: You must override the alarm within 60 seconds. If not, the system will automatically re-arm. EXAMPLE: To Override The System With The Password Code 83, 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2.
1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter and buttons can be used to lock and unlock the door (if the option is installed), however once the button is pressed, the vehicle’s starter disable device, (where installed) will be disengaged allowing the vehicle to start. 3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3 seconds.
Circuit” will interpret this pattern of triggers as false alarm. After the third trigger, “Noise Abatement Circuit” ignores, or bypasses, that sensor or switch until the other sensor or switch is trigger. “Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trigger ceases. O.
P. SYSTEM’S TRIGGER CHECK first, within 3 seconds press Press the transmitter (C) button. It responds with one melody sound and all trigger’s records will immediately displayed on the LCD screen. Q. SYSTEM’S STATUS CHECK When you want to check the system’s present status through the LCD screen, Press the transmitter button twice, within 3 seconds press It responds with one melody sound. (C) button. R. DRIVER PAGING It is useful the event that someone wants to page the driver of the parked vehicle.
S. DOME LIGHT CONVENIENCE DELAY & SUPERVISION The alarm with a unique feature which will turn on your vehicle dome light as following: 1. Upon disarming, the interior light will remain on for 30 seconds. 2. If the vehicle is intruded, the interior light will flash for the same duration as the siren. Note: Turn on the ignition switch or arm the alarm will turn off the dome light. T. IGNITION CONTROL DOOR LOCK/UNLOCK.
Y. SECOND VEHICLE SECURITY OPERATION: Your 5-button remote transmitter can be utilized to control a second vehicle security system, To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. nd Programming the Transmitter to 2 Car Enter: 1. Turn the ignition key ON 3 times. (Finishing in the ON position) nd 2. Press valet switch 2 times, holding in on the 2 push, you will hear a long siren chirp. (Release the valet switch) 3.
REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, 1. Press button once on the transmitter. 2. The parking light will activate to indicate the remote start received the signal. 3. The engine will start approximately 5 seconds. 4. Once the engine is running, after couple seconds the parking light will turn on again and climate controls will activate and adjust the vehicles interior temperature to your preset setting.
Turbo charge mode keeps the engine running after arriving at your destination for a programmable period of 1, 3 or 5 minutes, This allows the vehicle’s engine time to conveniently cool down the turbo after you have left the vehicle. To activate: 1. While the engine is running, pull up the hand brake and place the transmission gear in the park position. and buttons at the 2. Before turning off the engine, press and release same time.
light will flash (3) times. The siren or horn chirps (3) times. The vehicle is now programmed to start every (3) hours. 3-b. Daily Timer Start: Depress the transmitter button ( ) button. The parking light will flash (6) times. The siren chirps (6) times. The vehicle is now programmed to start at the real time of the next day. Your set time for the next day engine start flashes for approx. 3 seconds on the LCD screen. After 3 seconds the icon stays displayed on the LCD screen.
4. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed. 5. Press button once on the remote transmitter under remote start mode. 6. Move the optional remote start enable toggle switch to OFF position. (If installed) 7. The vehicle refused to start running after {3} unsuccessful attempts. I. DISABLING THE REMOTE START SYSTEM: (If installed) This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally.
1. Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery. Your Auto Page equipment is guaranteed for “life” to the original purchaser/user of the equipment and the original vehicle in which it was installed by an authorized installer under the following conditions: If the product proves defective (according to Auto Page's testing) within the first year, the defective unit may be exchanged or repaired free of charge.
This WARRANTY CARD is for your record. However, Autopage reserves the right to request you to submit this WARRANTY CARD, which must have complete information to receive warranty service. Please keep this card in a secured place. AUTOPAGE WARRANTY SERVICE CARD Model: _______________ Serial # _______________ CUSTOMER TO COMPLETE DEALER TO COMPLETE Mr./Mrs./Ms.
960 Knox Street Unit B Torrance, California 90502 Main Office: 310-323-1800 Customer Service: 800-262-2527 Ext. 462 www.autopageusa.
