Installation Manual

ManualsBrandsAuto Ventshade ManualsAutomotiveAuto Ventshade 12071 Ventshade with Stainless Steel Finish, 2-Piece Set for 1983-1992 Ford Ranger, 1984-1990 Bronco II

Installation Instructions

Ventshade® Deflector

Page 1 of 2

Front Driver

Side Visor

Front Passenger

Side Visor

I - Sheet Number VS08 Rev.B

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

• CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

Car Wash Supplies Clean Towel

• A trial fit is recommended to ensure proper positioning and fit.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash and dry your vehicle to remove any debris and/or dirt from the installation area.

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

Clip x10

Lower window. Use a putty knife to grasp rubber

window channel and pull down to the extent shown.

Contents - 2 Piece Set

Tools Required

Preparation Before Painting / Installation

rubber window channel

Putty Knife

Look up into the window channel and note the position of several

metal tabs. These tabs are where the clips which hold the deflec-

tor in place will be attached.

cross

section of

window

channel

metal tab

Drill

Screw x10

Phillips Screwdriver

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number VS08 Rev.B Ventshade® Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Center a clip on one of the metal tabs, as shown. Drill a 5/64” diameter hole, using the hole in the clip as a guide. NOTE: make sure the hole goes THROUGH the metal tab. Start one screw into the clip, then place the clip on the tab where the hole was drilled. Do NOT tighten! Leave the clip loose. Repeat Steps 1-3 for the 2nd, 3rd, and 4th clips. Set the 5th clip aside for now.
PAGE 3
Instructions d’installation I – Feuille numéro VS08 Rév.B Ventshade® Deflector Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1-800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que la visière est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Start one screw into the clip, then place the clip on the tab where the hole was drilled. NE PAS serrer! Conserver le clip dégagé. Répéter les étapes 1 à 3 pour le 2e, le 3e et le 4e clips. Mettre le 5e clip de côté pour l’instant. Centrer un clip sur l’une des languettes métalliques, comme illustré.
PAGE 5
Instrucciones de instalación Hoja informativa N.° VS08 Rev. B Ventshade® Deflector Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la visera esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación AVISO: La colocación real puede variar con respecto a las ilustraciones. Comience por colocar un tornillo en la presilla, luego ubique la presilla en el orificio de la lengüeta. NO la ajuste Deje la presilla suelta. Repita los pasos 1 al 3 para la 2da, 3ra y 4ta presilla. Por ahora, deje la 5ta presilla a un lado. Centre una presilla en una de las lengüetas metálicas, como se indica. Perfore un orificio de 5/64” de diámetro utilizando como guía el orificio de la presilla.