User Manual

ManualsBrandsAuto Ventshade ManualsAutomotiveAuto Ventshade 194361 in-Channel Ventvisor Side Window Deflector, 4-Piece Set for 2015-2018 Hyundai Sonata

Installation Instructions

Contents - 2 Piece Set

Page 1 of 2

Contents - 4 Piece Set

Alcohol Pad x4

Alcohol Pad x2Front Driver

Side Visor

Front Passenger

Side Visor

Front Driver

Side Visor

Front Passenger

Side Visor

Rear Driver

Side Visor

Rear Passenger

Side Visor

I - Sheet Number VV148 Rev.B

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

• CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

Tools Required

Car Wash Supplies Clean Towel

Preparation Before Painting / Installation

• A trial fit is recommended to ensure proper positioning and fit.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash and dry your vehicle to remove any debris and/or dirt from the installation area.

NOTE: Actual product may vary from illustration.

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

1 2

free end

top flange

rear

flange

front

flange

free end

Remove tape liner from front flange. Peel back

2” of tape liner from each end of top flange.

Ventvisor

Deflector

Scotch Brite Pad

Roll down window. Buff the inside felt surface

with scotch brite pad. Then clean with alcohol

pad.

clean

inside of vehicle

NOTE: visors mount on the inside of the window

channel.

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number VV148 Rev.B Ventvisor® Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Apply pressure to all flange edges to ensure proper adhesion. Remove tape liner by pulling on free ends. Insert visor rear flange first. Rear flange inserts between the trim and the exterior surface. The front & top flange slides into the window channel.
PAGE 3
Instructions d’installation I – Feuille numéro VV148 Rév.B Ventvisor® Deflector Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1-800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que la visière est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Insérez la bride arrière de la visière première. Le rebord arrière s’insère entre la garniture de glace et la surface extérieure. Les rebords avant et supérieur s’engagent dans la glissière de glace. 3 Exercez une pression sur tous les bords des brides afin de vous assurer que la pièce colle bien. Retirer la protection d’adhésif en tirant sur les extrémités libres.
PAGE 5
Instrucciones de instalación Hoja informativa N.° VV148 Rev.B Ventvisor® Deflector Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la visera esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación AVISO: La colocación real puede variar con respecto a las ilustraciones. Ejerza presión en todos los bordes del reborde para que se adhiera correctamente. Retire la cinta protectora tirando de los extremos libres. Insertar pestaña trasera visera primero. El reborde trasero se introduce entre la banda lateral y la superficie exterior. El reborde superior frontal se desliza por el canal de la ventanilla.