Installation Manual

ManualsBrandsAuto Ventshade ManualsAutomotiveAuto Ventshade 194381 in-Channel Ventvisor Side Window Deflector, 4-Piece Set for 2017-2018 Ford F-250, F-350, F-450 Super Duty with SuperCrew Cab

Installation Instructions

Ventvisor® Deflector

Contents - 2 Piece Set

Page 1 of 2

Contents - 4 Piece Set

Alcohol Pad x4

Alcohol Pad x2

Front Driver

Side Visor

Front Passenger

Side Visor

Front Driver

Side Visor

Front Passenger

Side Visor

Rear Driver

Side Visor

Rear Passenger

Side Visor

I - Sheet Number VV140 Rev.A

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

• CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

Tools Required

Car Wash Supplies Clean Towel

Preparation Before Painting / Installation

• A trial fit is recommended to ensure proper positioning and fit.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash and dry your vehicle to remove any debris and/or dirt from the installation area.

NOTE: Actual product may vary from illustration.

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

1 2

Clean the window channel

with an alcohol pad.

Peel back 2” (5 cm) of tape line from each end of

top flange.

free end

top flange

rear

flange

front

flange

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number VV140 Rev.A Ventvisor® Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Insert visor into window channel. Front and rear flanges insert between the rubber trim and the mirror cap / door frame. Top flange slides into the window channel. 3 Remove tape liner by pulling on free ends. Raise window slowly and leave up for 24 hours to secure visor to window channel. 4 4 Piece Set Install the rear visors using the same preparation and installation methods as the front visor.
PAGE 3
Instructions d’installation I – Feuille numéro VV140 Rév.A Ventvisor® Deflector Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1-800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que la visière est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Insérer la visière dans la glissière de glace. Les rebords avant et arrière s’insèrent entre la garniture en caoutchouc et le couvercle du rétroviseur / cadre de portière. Le rebord supérieur s’engage dans la glissière de glace. 3 Retirer la protection d’adhésif en tirant sur ses extrémités libres.
PAGE 5
Instrucciones de instalación Hoja informativa N.° VV140 Rev. A Ventvisor® Deflector Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la visera esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación AVISO: La colocación real puede variar con respecto a las ilustraciones. Inserte la visera en el canal de la ventanilla. El reborde frontal y el reborde trasero se insertan entre la banda de goma y la cubierta del espejo o el marco de la puerta. El reborde superior se desliza por el canal de la ventanilla. 3 Retire la cinta protectora tirando de los extremos libres.