Installation Manual

ManualsBrandsAuto Ventshade ManualsAutomotiveAuto Ventshade 25627 Bugflector II Dark Smoke Hood Shield for 2003-2006 Ford Expedition

Bugﬂector - Bugﬂector II - Carﬂector

Page 1 of 2

Installation Instructions

Tools Required

Contents

Car Wash Supplies

Phillips ScrewdriverClean Towel

Bump On x4Bugflector Fastner x4

I - Sheet Number BF18 Rev.A

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

• CAUTION - Before driving, ensure that the hood shield is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

NOTE: Actual product may vary from illustration.

Preparation Before Painting / Installation

• A trial fit is recommended to ensure proper positioning and fit.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash and dry your vehicle to remove any debris and/or dirt from the installation area.

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

Raise hood. Locate 4 holes on underside of hood that align with the holes in hood

shield and clean to remove any dust or debris.

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number BF18 Rev.A Bugﬂector - Bugﬂector II - Carﬂector For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the hood shield is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from drawings. Install fasteners by either pushing or screwing. Align holes in hood shield with holes in underside of hood and position in place. Hood Hood Shield Fastener 3 4 Close hood. Do not overtighten Install (4) bumpons on painted hood/fender surface. 6 5 X4 X4 Care and Cleaning • Wash only with mild soap & dry with a clean cloth.
PAGE 3
Instructions d’installation I- Feuille numéro BF18 Rév.A Bugﬂector - Bugﬂector II - Carﬂector Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que le pare-insectes est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Installer les fixations en les poussant ou en les vissant. Aligner les trous du pare-insectes et ceux du dessous du capot et mettre le pare-insectes en place. Capot Pareinsectes Fixation 3 4 Fermer le capot. Ne pas trop serrer Installer (4) butoirs sur la surface peinte du capot / de l’aile.
PAGE 5
Instrucciones de instalación Hoja informativa N.° BF18 Rev. A Bugﬂector - Bugﬂector II - Carﬂector Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la visera deflectora esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación NOTA: El uso real puede variar levemente de ilustraciones. Instale los sujetadores empujando o atornillando. Alinee los orificios de la cubierta para capó con los orificios de la parte inferior del capó y coloque la cubierta en su lugar. Capó Cubierta para capó Sujetador 3 4 Cierre el capó. Do not overtighten X4 Instale (4) soportes en el capó pintado / la superficie del guardabarros.