Installation Manual

ManualsBrandsAuto Ventshade ManualsAutomotiveAuto Ventshade 94155 Original Ventvisor Side Window Deflector Dark Smoke, 4-Piece Set for 2009-2014 Ford F-150 SuperCrew | Also fits 2010-2014 Raptor SuperCrew

Installation Instructions

Ventvisor® Deflector

Page 1 of 2

Alcohol Pad x2Driver Side

Visor

Passenger Side

Visor

I - Sheet Number VV57 Rev.B

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

• CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

Car Wash Supplies Clean Towel

Preparation Before Painting / Installation

• A trial fit is recommended to ensure proper positioning and fit.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash and dry your vehicle to remove any debris and/or dirt from the installation area.

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

1 2

Clean the painted surface where the visor will

mount with an alcohol pad.

Remove the tape liner from the rear flange. Peel back

2” (5cm) of tape liner from each end of top flange.

rear

flange

top flange

free end

front flange

free end

Note: Visors mount on the outside painted

surface of the door frame.

Contents - 2 Piece Set

Contents - 4 Piece Set

Tools Required

Alcohol Pad x4Driver Side

Visor

Passenger Side

Visor

Rear Passenger

Side Visor

Rear Driver

Side Visor

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number VV57 Rev.B Ventvisor® Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Carefully lift the mirror cap cover to create a 1/4” gap. While lifting mirror cap, insert front flange of visor underneath it. Release mirror cap. 1/4” gap 3 4 Align the passenger side visor with the previously cleaned surface. 5 With the visor in its final position, remove the remaining tape liner by pulling on free ends. 6 Press along visor flanges to ensure proper adhesion.
PAGE 3
Instructions d’installation I – Feuille numéro VV57 Rév.B Ventvisor® Deflector Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1-800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que la visière est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Soulever délicatement le couvercle du rétroviseur pour obtenir un espace de 6 mm (1/4 po). Tout en tenant le couvercle du rétroviseur soulevé, insérer le rebord de la visière dans l’espace créé. Relâcher le couvercle du rétroviseur. Espace de 6 mm (1/4 po) 3 4 Placer la visière côté passager sur l’endroit préalablement nettoyé.
PAGE 5
Instrucciones de instalación Hoja informativa N.° VV57 Rev. B Ventvisor® Deflector Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la visera esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación AVISO: La colocación real puede variar con respecto a las ilustraciones. Levante cuidadosamente la cubierta plástica del espejo para crear un espacio de 1/4”. Mientras levanta la cubierta del espejo, coloque el reborde frontal de la visera debajo de la cubierta. Suelte la cubierta del espejo. espacio de 1/4” 3 4 Alinee la visera del acompañante con la superficie que limpió anteriormente.