User guide

Quick Installation Guide http://www.autostart.ca/ P. 7
Supplementary Information
Fifth Relay Output (2nd IGN, ACC or CRANK)
Remote car starters of this series are equipped with an on-board
high-current programmable 5
th
relay that can be used to power a
second ignition, accessory or crank wire. The unit uses 3 sets of
pins; each set corresponds to a specific function of the output. In
order to activate one of the three possible functions, you must
place the jumper (supplied) on one of the three sets of pins and
connect the 14 AWG wire to the second IGN. / ACC. / CRANK
wire of the vehicle.
Caution!
Only one set of pins can be used at one time. Using more than one jumper may result in serious damage to the vehicle. The
relay output rating on this unit is 25a at most. Defective oem solenoid switches can sometimes draw up to 50 or 60a, causing
the 30a fuse to blow. Always verify your circuit with an appropriate measuring device.
Tach jumper settings
Some new vehicles have a higher TACH voltage threshold,
which would fall out of the normal TACH trigger circuit of the
remote car starter. Changing the jumper to TACH Threshold
HIGH will allow the module to properly detect the TACH signal.
Testing
Before putting back the vehicle together, it is recommended to
check that the system operates properly. The following testing
procedures should be used to verify proper installation and
operation of the system. Before testing, make sure that all
connections are soldered and that the unit is plugged in.
 If installed on a MANUAL transmission, make sure the
system properly enters and exits ready mode:
Ready mode is a sequence of steps that must be followed in order to allow manual transmission vehicles to be remote
started. To get into ready mode:
If Ready Mode is enabled by remote If Ready Mode is enabled by handbrake
1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the neutral position.
2. With the engine already running, apply the
parking brake once and release the brake pedal.
2. With the engine already running, apply the parking
brake twice within 10sec.
Make sure to release the brake pedal.
The parking lights will flash 3 times quickly and
remain lit.
Skip to step 4.
3. Within 20 sec. of engaging the parking brake,
press and hold , or on the
transmitter.
The parking lights will flash 3 times quickly and
remain lit.
-
4. Remove the key: the engine will continue running.
5. Exit the vehicle and close all doors, hood and trunk.
6. Press for approx. 1 second either:
x to lock the doors and shut down the engine;
x to unlock the doors and shut down the engine;
x to shut down the engine without affecting the doors.
7. The parking lights will flash twice to confirm ready mode activation.
P. 2 http://www.autostart.ca Quick Installation Guide
x When learning the transmitter, the parking lights will flash 5 times quickly.
x Upon the first successful remote start, the system will lock the transmission settings to manual mode.
To install this unit in a vehicle with an automatic transmission:
1. Cut the loop on the pc board (Yellow wire).
2. Make sure the Orange handbrake wire is not
connected to any of the vehicle circuits.
3. Make all the regular connections.
4. Power up the unit. The parking lights will flash 4 times.
5. When learning the first transmitter, the parking lights will flash 5 times quickly then give 2 slow flashes.
6. Upon the first successful remote start once the yellow loop has been cut, the system will lock the transmission
settings to automatic mode.
Note: If upon pressing the START button, the parking lights give 3 slow flashes, make sure that the Orange handbrake wire is
not connected and that the yellow loop is cut and isolated.
Resetting the Module
WARNING! By resetting the module, all programmed values are erased  i.e.: tach, transmitter as well as
programming options. The programming options are returned to their default values.
x Enter programming Mode (see p. 1).
x Once having reached the programming mode, quickly press and release the brake pedal until the parking lights flash 8
times.
Transmitter Programming Procedure
1. Enter programming Mode (see p. 1).

the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position.
3. Press and hold the LOCK button and keep it down until the siren or horn chirps twice and the parking lights flash 5 times
quickly.
4. The transmitter has been stored in memory.
5. To exit: close the hood. Note: Each unit can store 4 remotes in its memory.
To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button (instead of LOCK or
UNLOCK) in step 3 of the transmitter programming procedure.
Entering Programming Options
1. Enter programming Mode (see p. 1)

the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons. Note: For vehicles that
require the ignition to be turned ON to activate the brake, follow these steps:
a. Turn the ignition ON; The parking lights will turn OFF
b. After 4 seconds the parking lights will turn ON and then press the brake.
LOCK .............................to access mode 1;
UNLOCK ........................to access mode 2;
TRUNK……………… ……to access mode 3;
START/STOP…………….to access mode 4.
The parking lights will flash and the horn or siren will chirp (if programmed) once, twice, three or four times to confirm entry into
a mode.
3. Release the brake pedal.
4. Once the desired mode has been selected, the unit will fall (by default) into function #1 of that mode; you can now select the
option you want in function 1. Once this option has been chosen, the unit will move on to function 2 of the mode selected, and so
on.
LOCK ............................ for Option 1;
UNLOCK ....................... for Option 2;
TRUNK .......................... for Option 3;
START/STOP ................. for Option 4.
Programming Options
MODE 1
* INDICATES DEFAULT SETTING
FUNCTION 1 – Ignition-controlled door locks
OPTION 1* Ignition lock DISABLED
OPTION 2 Ignition lock ENABLED
OPTION 3 Ignition unlock only
OPTION 4 Ignition lock only
FUNCTION 2 – Secure Lock
OPTION 1* Secure lock DISABLED
OPTION 2 Standard secure lock ENABLED
OPTION 3 Smart secure lock ENABLED
FUNCTION 3 – Starter Kill arming mode
OPTION 1* Passive arming (60 sec.)
OPTION 2 Active arming
OPTION 3 Passive arming (3 min.)
FUNCTION 4 – Door lock/unlock pulse timing
OPTION 1* 7/10-sec. lock/unlock pulses
OPTION 2 4-sec. lock/unlock pulses