User guide

Quick Installation Guide http://www.autostart.ca/ P. 3
OPTION 3 7/10-sec. lock pulse and two ¼ -sec. unlock pulses
OPTION 4 1/10-sec. lock/unlock pulses
FUNCTION 5 – LED flashing
OPTION 1* ENABLED (without starter kill
Æ
will flash only when ignition is OFF)
OPTION 2 DISABLED
OPTION 3 ENABLED (with starter kill Æ will ONLY flash when the starter kill engages.
This option should be selected ONLY if the starter kill is installed.)
MODE 2
* INDICATES DEFAULT SETTING
FUNCTION 1 – Safe Start
OPTION 1 Safe start ENABLED
OPTION 2* Safe start DISABLED
OPTION 3 “Swap Start” – enhanced safe start mode with extended safety:
To start the engine: press the PANIC/AUX then LOCK buttons
To trigger AUX 2: press the START/STOP button
FUNCTION 2 – Engine Run Time
OPTION 1 Run Time = 3 minutes in gas mode / 8 minutes diesel mode
OPTION 2* Run Time = 15 minutes in gas mode / 20 minutes diesel mode
OPTION 3 Run Time = 25 minutes in gas mode / 30 minutes diesel mode
FUNCTION 3 – Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)
OPTION 1 Idle mode & turbo mode DISABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 2* Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 3 Idle mode & turbo mode ENABLED (AUTO) / turbo mode ENABLED (MANUAL)
FUNCTION 4 – Engine type and Cold Weather Mode
OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)
OPTION 2* Gas mode with 3-minute run time in cold weather mode
OPTION 3 Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)
OPTION 4 Diesel mode with 8-minute run time in cold weather mode (7-sec. wait to start delay)
FUNCTION 5 – Ignition valet
OPTION 1 Ignition valet – DISABLED
OPTION 2* Ignition valet – ENABLED
MODE 3
* INDICATES DEFAULT SETTING
FUNCTION 1 – AUX 1 Programming
OPTION 1 Horn confirmation upon the 2
nd
press of the LOCK button.
OPTION 2* Priority door access
OPTION 3 Horn confirmation upon the 1
st
press of the LOCK button.
FUNCTION 2 – AUX 2 Programming
OPTION 1 Constant output by pressing PANIC then LOCK buttons / constant lock or unlock output if
LOCK or UNLOCK button is pressed for more than 3 sec.
OPTION 2* Toggle ON/OFF (with 30-second timeout) by pressing PANIC then LOCK buttons
OPTION 3 4-minute toggle by pressing PANIC then LOCK buttons (active only when running under
remote start)
OPTION 4 Priority door access
FUNCTION 3 – AUX 3 Programming
OPTION 1 1-sec. output when TRUNK button is pressed for 3 sec. with ignition OFF or under
remote run
OPTION 2* Constant output while the TRUNK button is pressed
OPTION 3 Disarm/rearm pulse with TRUNK
FUNCTION 4 – External Trigger
OPTION 1 Zone 3 disarm/rearm (trunk pin: a disarm pulse is sent before the trunk opens, the vehicle
rearms 4 seconds after the trunk is closed)
OPTION 2* Key sense
OPTION 3 Engine start / stop
OPTION 4 Pager
MODE 4
* INDICATES DEFAULT SETTING
FUNCTION 1 – Multi-Level Features
OPTION 1 Multi-car Features, Basic Features, Customized Features
OPTION 2* Basic Features, Multi-car Features, Customized Features
OPTION 3 Customized Features, Multi-car Features, Basic Features
OPTION 4 Basic Features, Customized Features, Multi-car Features
FUNCTION 2 – Alarm Control
OPTION 1 ENABLED (HORN option must be enabled)
OPTION 2* DISABLED
FUNCTION 3 – Ready Mode Option
OPTION 1 Enabled by handbrake
OPTION 2* Enabled by remote
P. 6 http://www.autostart.ca Quick Installation Guide
FUNCTION 3 - Bypass
OPTION 1 ADS
OPTION 2* Xpresskit
OPTION 3 Fortin
FUNCTION 4 – Bypass Type
OPTION 1 One-Way communication
OPTION 2* Two-Way communication (For Xpresskit bypass only)
Bypass
Remote starters of this series have the ability to work in two way mode (D2D) with Xpresskit bypass modules. They also offer
one way communication with Xpresskit , ADS and Fortin brand bypass modules.
Note: For Hardware 5.0 and higher, there can only be one bypass connected to the unit.
Virtual Tach System
* Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to develop. VTS
is able to effectively monitor the engine starting sequence and release the starter at the right time without physically connecting
the tach wire to the remote starter. The VTS constantly monitors the data and readjusts itself automatically in order to maximize
its capability to start the engine properly in any weather or deteriorating battery condition (automatic transmission only).
Optional Time Delay Adjustment in Virtual Tach System
Follow these steps to program crank time adjustment, if needed:
1. Enter programming mode (see p. 1)  the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, press and hold the brake pedal and press the LOCK and UNLOCK buttons simultaneously  the
parking lights will flash 4 times. Do not release the brake pedal. Note: For vehicles that require the ignition to be turned
ON to activate the brake, follow these steps:
a. Turn the ignition ON; The parking lights will turn OFF
b. After 4 seconds the parking lights will turn ON and then press the brake.
3. Press the LOCK button if you wish to increase the time delay or the UNLOCK button if you want to decrease it. The time
delay will be increased or decreased by 50ms. and the parking lights will flash once every time the LOCK or UNLOCK
button is pressed.
4. Press the TRUNK button to save the settings you have entered.
5. Release the brake pedal – the time delay programming is now complete.
Multi-speed Tach Programming
1) Enter programming mode (see p. 1)  the parking lights will stay on for up to 20 seconds.
2) Before the lights go out, press and hold the brake pedal and press the LOCK and UNLOCK buttons simultaneously 
the Parking lights will flash 4 times, and then the siren or horn will chirp 4 times. At that point, release the brake pedal.
Note: For vehicles that require the ignition to be turned ON to activate the brake, follow these steps:
i) Turn the ignition ON; The parking lights will turn OFF
ii) After 4 seconds the parking lights will turn ON and then press the brake.
3) Start up the engine and allow the vehicle to reach regular engine idle speed.
4) Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the parking
lights output click 5 times; the siren will chirp twice.
5) Release the brake pedal the tach programming is now complete.
Horn Honk Timing adjustment
1) Enter programming mode (see p. 1)
2) Press and hold the brake pedal, then simultaneously press the UNLOCK and sTART/STOP buttons  the horn will
chirp 5 times. Note: For vehicles that require the ignition to be turned ON to activate the brake, follow these steps:
i) Turn the ignition ON; The parking lights will turn OFF
ii) After 4 seconds the parking lights will turn ON and then press the brake.
3) Release the brake pedal.
i) To change the timing:
ii) To increase the Horn pulse by 3 ms, press the LOCK button.
iii) To decrease the pulse by 3 ms, press the UNLOCK button.
iv) To increase the pulse by 10 ms, press the sTART/ Stop button.
4) To decrease the pulse by 10 ms, press the TRUNK button.
5) To save the new settings: press LOCK and UNLOCK. If 3 chirps are returned, the new settings have been saved.