Owners manual

ManualsBrandsAutoVentshade ManualsAutomotiveAuto Ventshade 1774036 Ventvisor Low Profile Deflector 4 pc. Fits 16-19 Tacoma

Installation Instructions

Contents - 2 Piece Set

Page 1 of 2

Contents - 4 Piece Set

Alcohol

Pad x4

Front Driver

Side Visor

Front Passenger

Side Visor

Front Driver

Side Visor

Front Passenger

Side Visor

Rear Driver

Side Visor

Rear Passenger

Side Visor

I - Sheet Number VV139 Rev.B

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

• CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

Tools Required

Car Wash Supplies Clean Towel

Preparation Before Painting / Installation

NOTE: Actual product may vary from illustration.

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

1 2

top flange

Alcohol Pad x2

Scotch Brite

Pad

Scotch Brite

Pad

Roll down window. Buff the inside felt surface

with scotch brite pad. Then clean with alcohol

pad.

clean

inside of vehicle

NOTE: visors mount on the inside of the window

channel.

Ventvisor® Deflector

• A trial fit is recommended to ensure proper positioning and fit. Note that the visors are stamped with an

L or R following the part number, indicating Left or Right side placement.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash your vehicle to remove any debris and/or dirt.

• Dry with a clean towel.

free end

remove remove

free end

Remove the tape liner from the front & rear flanges.

Peel back 2” of tape liner from each end of top flange.

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number VV139 Rev.B Ventvisor® Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Insert visor into window channel, front flange first. 3 Apply pressure to all flange edges to ensure proper adhesion. Remove tape liner by pulling on free ends. 4 NOTE: It is necessary to both hold the visor up into the window channel AND pull the bottom of the visor slightly outward while raising the glass to seat visor properly.
PAGE 3
Instructions d’installation I – Feuille numéro VV139 Rév.B Ventvisor® Deflector Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1-800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que la visière est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Exercez une pression sur tous les bords des brides afin de vous assurer que la pièce colle bien. Retirer la protection d’adhésif en tirant sur les extrémités libres. Insérer le rebord avant de la visière dans la glissière de glace en premier.
PAGE 5
Instrucciones de instalación Hoja informativa N.° VV139 Rev.B Ventvisor® Deflector Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la visera esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación AVISO: La colocación real puede variar con respecto a las ilustraciones. Inserte la visera en el canal de la ventanilla comenzando con el reborde frontal. Ejerza presión en todos los bordes del reborde para que se adhiera correctamente. Retire la cinta protectora tirando de los extremos libres.