Owners manual

ManualsBrandsAutoVentshade ManualsAutomotiveAuto Ventshade 94782 Ventvisor Deflector 4 pc. Fits 17-19 Rogue Sport

Installation Instructions

Ventvisor® Deflector

Contents - 2 Piece Set

Page 1 of 2

Contents - 4 Piece Set

Alcohol Pad x4

Alcohol Pad x2

Front Driver

Side Visor

Front Passenger

Side Visor

Front Driver

Side Visor

Front Passenger

Side Visor

Rear Driver

Side Visor

Rear Passenger

Side Visor

I - Sheet Number VV127 Rev.B

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

• CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

Tools Required

Car Wash Supplies Clean Towel

Preparation Before Painting / Installation

• A trial fit is recommended to ensure proper positioning and fit.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash and dry your vehicle to remove any debris and/or dirt from the installation area.

NOTE: Actual product may vary from illustration.

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

1 2

Lower drivers side window and clean window frame

and chrome trim with an alcohol pad.

NOTE: Visors mount on the OUTSIDE door trim.

chrome trim

lateral flange

free end

rear flange

Peel back 2” (5 cm) of tape liner from each end of lateral flange.

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number VV127 Rev.B Ventvisor® Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the vent visor is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Align the visor with the previously cleaned surface. The flanges of the visor attach to the surface of the window’s chrome trim. Verify proper positioning. With the visor in its final position, remove remaining tape liner by pulling on free ends. 4 3 Apply pressure along all flanges to ensure adhesion of tape to the trim surfaces.
PAGE 3
Instructions d’installation I – Feuille numéro VV127 Rév.B Ventvisor® Deflector Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1-800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que la visière est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Aligner la visière et la portière. Les brides de la visière fixer à la surface de chrome de la fenêtre trim. Vérifier le positionnement. Une fois la visière en position finale, retirer le reste de la protection d’adhésif en tirant sur les extrémités libres. 4 3 Appuyer le long de tous les rebords pour assurer la bonne adhésion du ruban sur les surfaces de la garniture.
PAGE 5
Instrucciones de instalación Hoja informativa N.° VV127 Rev. B Ventvisor® Deflector Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la visera esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación AVISO: La colocación real puede variar con respecto a las ilustraciones. Alinee la visera con la puerta. Los rebordes de la visera adhieren a la superficie de cromo de la ventana de corte. Verifique que esté correctamente colocada. Una vez que la visera se encuentre en su posición definitiva, quite la cinta protectora restante tirando de los extremos libres. 4 3 Presione todos los rebordes para asegurarse de que la cinta se adhiera a las superficies de la banda.