Owners manual

ManualsBrandsAutoVentshade ManualsAutomotiveAuto Ventshade 97130 Aeroshade Rear Side Truck Window Cover Fits 04-08 F-150

Aeroshade

Preparation Before Painting / Installation

• A trial fit is recommended to ensure proper positioning and fit.

• Check fit of parts before painting as we will not accept the return of modified or painted parts.

• Wash your vehicle to remove any debris and/or dirt from installation area.

• Dry the installation area with a clean towel.

Page 1 of 3

Installation Instructions

I - Sheet Number AS01 Rev.A

Important Safety Information

• CAUTION - Before driving, ensure that the window cover is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Contents

NOTE: Actual product may vary from illustration.

Alcohol Pad x2

Tools Required

Car Wash Supplies

Drivers side window

cover

Clean Towel

Passenger side

window cover

Installation Steps

NOTE: Actual application may vary slightly from illustrations.

Installation Steps

Clean the installation area with alcohol pad. Peel back 2” (5 cm) of tape liner.

Summary of content (6 pages)

PAGE 1
Installation Instructions I - Sheet Number AS01 Rev.A Aeroshade® For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the window cover is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Align window cover with the previously cleaned window trim. Press on exposed tape area to adhere to vehicle. Remove remainder of tape liner by pulling on free ends. 4 3 Press firmly along flanges to ensure proper adhesion to vehicle. Repeat Steps 1- 5 for passenger side window cover. 5 Care and Cleaning • Wash only with mild soap & dry with a clean cloth.
PAGE 3
Instructions d’installation I- Feuille numéro AS01 Rév.A Aeroshade® Pour obtenir une installation correcte et le meilleur ajustement possible, lire toutes les instructions AVANT de commencer. Pour toute assistance technique ou obtention de pièces manquantes, appeler le service des relations avec la clientèle au 1-800-241-7219. Informations importantes concernant la sécurité • ATTENTION – Avant de conduire, s’assurer que couverture de fenêtre est solidement assujettie sur le véhicule.
PAGE 4
Étapes d’installation REMARQUE : La méthode d’application peut être légèrement différente de celle représentée par les illustrations. Aligner le cache-glace et la garniture de glace préalablement nettoyée. Appuyer sur la partie exposée du ruban adhésif pour le faire adhérer au véhicule. Retirer le reste de la protection d’adhésif en tirant sur les extrémités libres. 3 4 Appuyer fermement tout le long des rebords, pour assurer une bonne adhésion au véhicule.
PAGE 5
Installation Instructions Hoja informativa N.° AS01 Rev. A Aeroshade® Para una instalación adecuada y el mejor ajuste posible, lea todas las instrucciones ANTES de comenzar. Si desea recibir asistencia técnica u obtener piezas faltantes, llame al Servicio al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN - Antes de conducir, asegúrese de que la cubierta de la ventana esté correctamente anclada al vehículo.
PAGE 6
Pasos de instalación AVISO: La colocación real puede variar con respecto a las ilustraciones. Presione sobre la cinta expuesta para fijar al vehículo. Retire la cinta protectora restante tirando de los extremos libres. Alinee la cubierta de la ventanilla con la banda lateral que limpió anteriormente. 3 4 Presione firmemente sobre los rebordes para asegurarse de que se adhieran correctamente al vehículo. Repita los pasos 1 al 5 para colocar la cubierta de la ventanilla del acompañante.