® THE PE RF O R M A N C E YO U NEED ® Bluetooth® Headset Please read this user’s guide before using your new headset.
Package Contents Bluetooth Headset USB Charging Cable User’s Guide Charge Your Headset When the headset beeps and the indicator repeatedly double-flashes red, charge your headset. If you do not charge your headset, it will turn off automatically. Normal charging takes about 1.5 hours. The fully charged battery provides up to 5 hours of talk time and up to 168 hours of standby.
1. Connect the USB plug of the supplied charging cable to the USB port of your computer or to a USB charger. 2. Connect the cable’s Micro-USB plug to the headset’s USB charging port. The Indicator lights red when charging and turns off when fully charged. 3. Unplug the charging cable when the headset is fully charged. Pairing 1. Press and hold the Multifunction button for 7 seconds to enter pairing mode. The Indicator flashes red and blue. Your headset searches for Bluetooth-enabled devices. 2.
Multifunction Button VOL + VOL - Indicator Microphone 4 4
3. To pair a second Bluetooth-enabled device, press and hold VOL+ for 3 seconds to enter pairing mode. The headset will disconnect from the first Bluetooth-enabled device automatically. Pair and connect with the second device, then manually connect the first device according to its pairing instructions. 4. Press and hold the Multifunction button for 2 seconds to turn off the headset. The Indicator flashes red twice.
Make and Receive Calls Press and hold the Multifunction button for 3 seconds to turn on the headset. The Indicator flashes blue three times. To make a call, use your mobile device as normal when the headset is connected. To redial the number you last called when no call is in progress, press the Multifunction button twice quickly. To activate voice dial when no call is in progress, press and hold VOL for 3 seconds until the phone starts voice dialing.
To mute or unmute the microphone during a call, press and hold VOL for 3 seconds. To toggle a call between your headset and your connected phone, press and hold the Multifunction button for 3 seconds. To switch two calls between two phones, press and hold VOL+ for 3 seconds. n Note: The button function may vary depending on your phone’s protocol. Specifications Battery Charge Time....................... 1.5 hours Operation Time..................................
FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Limited Warranty Ignition L.P.
damage; (e) transportation, shipping or insurance costs; (f) costs of product removal, installation, set-up service, adjustment or reinstallation; and (g) claims by persons other than the original purchaser. Should a problem occur that is covered by this warranty, take the product and the sales receipt as proof of purchase date to the place of purchase. Ignition L.P.
IF APPLICABLE, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, SHALL EXPIRE ON THE EXPIRATION OF THE STATED WARRANTY PERIOD. EXCEPT AS DESCRIBED ABOVE, IGNITION L.P.
You may contact Ignition L.P. at: Ignition L.P., 3102 Maple Ave., Suite 450, Dallas, TX 75201 02/09 For product support, call 1-866-315-0426 Complies with the European Union’s “Restriction of Hazardous Substances Directive,” which protects the environment by restricting specific hazardous materials and products. The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Ignition L.P. is under license.
