Specifications
38
5) DIAL AND MODEM PARAMETERS
Pre-
Dial
Delay
Wait
for
Dial
Tone
Anti-
Jam
Delay
Dial
tone
dete-
ction
Dial
Mode
Tel.
MSG
Time
Inter-
Call
Delay
Re-Dial
Cycles
(max.)
Pulse
Make
Pulse
Break
Inter
Digit
Delay
Rings
qut'y for
modem
Instant
mode
m
answer
Sec's
Sec's
Sec's
00 = No
01 = Yes
0= Pulses
1= DTMF
Sec's
Sec's
XX Cycle
5 mS
5 mS
50 mS
Tel. Rings
00 = No
01 = Yes
080
081
082
083
084
085
086
087
088
089
090
091
092
0
2
0
4
1
0
0
1
0
1
5
0
2
0
0
3
0
8
1
2
2
0
1
0
0
1
Rings
before
Answer
Answer
Now
(Modem)
DTMF
Length
Min.
Ring
Length
Min.
Ring
Cycle
Tel. Line
Test
Intervals
Ring
Time out
Rings
00 = No
01 = Yes
5 m’S
10 m’S
(10-20)
100 m’S
(7-25)
Minutes
(Max 99)
Seconds
(4-35)
091
092
093
094
095
096
097
1
0
0
1
1
9
1
5
1
5
0
0
0
6
Note address 091: The download is ENABLED by default. Enter a value of 21 at address 091 to disable modem (21 rings for
modem not accepted by telephone net). To ENABLE enter 01 to 20 at address 091. To enable Instant Modem Answer function
(Answer Now), hold-down key 6 then hold-down key 1. ‘A’ displayed in confirmation.
6) USER CODES SETTING Address 099 provides setting of user codes 01 to 17
099
USER 01
USER 02
USER 03
USER 04
USER 05
USER 06
USER 07
USER 0 8
1,2,3,4
Installer Code
USER 09
USER 10
USER 11
USER 12
USER 13
USER 14
USER 15
USER 16
USER 17
1,9,9,4
For programming End-User codes 1 to 17 (Arm/Disarm & Programming codes) via installer programming mode; enter to
address No. 099, then program new codes by first entering the code index (01, 02, 03..). User 1 code is the Master code (for
changing codes), user 17 code is the programming code - If changed code 1 or 17 make a note of the new codes.
To erase a code does not enter any digit after the code index number.
To send the Force Opening Code (Ambush) the user should enter the Disarming code in reverse order.
7) FACTORY DEFAULT SETTING: Enter 6 9 in address 200, to revert to factory default programming
8) COMMUNICATOR PARAMETERS
TELEPHONE
Receiver
Format
Handshake
Frequency
Data
Format
Protocol
Type
Check
Sum
Transmit
Rounds
Inter Rnd
Delay
Wait for
Handshake
(Parity)
Time
Time
No. 2
021
023
025
027
029
031
033
035
0
0
0
2
0
0
0
0
0
0
0
0
3
0
2
0
TELEPHONE
Receiver
Format
Handshake
Frequency
Data
Format
Protocol
Type
Sum
Check
Transmit
Rounds
Inter Rnd
Delay
Wait for
Handshake
(Parity)
Time
Time
No. 3
022
024
026
028
030
032
034
036
0
0
0
2
0
0
0
0
0
0
0
0
3
0
2
0
00 - Dialer only (No Communicator)
00=1400 Hz
00=3 X 1
00=Standard
00=None
00=2 Rnd
00=0.1 Sec
XX=Sec's
01 - Ademco, Silent Knight Slow,
Scantronic
01=2300 Hz
01=4 X 1
01=Extend
01=S. Check
01=1 Rnd
30=3 Sec
02 - Radionics Fast
03 - Sescoa, Vertex, DCI, Franklin
02=Hi/Low
02=4 X 2
3 Sec's is
04 - Silent Knight Fast
Default
05 - Radionics, DCI, Franklin Slow
02=Hi/Low
03=3 X 2
06 - Universal High Speed
**
07 - Contact ID/Ademco Fast*
00 - ‘No Communicator,’ is identical to ‘Dialer’ that generates sound upon alarm. ** For Contact ID, program 07 in 021 & 022 address.
* For Ademco Fast Receiver type 685 enter 02 at address 023 & 024.