User's Manual

ManualsBrandsAvalan Wireless Systems ManualsElectronics5.8GHz Wireless Ethernet Bridge Module

AW5800m-SR Module Integrator’s Kit

User’s Manual

Thank you for your purchase of the AW5800m-SR Module.

If you have any questions when configuring your AvaLAN

module

please send us an email: support@avalanwireless.com

Kit Contents:

2 AW5800m-SR RF Modules (RPSMA female)

2 AWP12 12in Pigtails (RPSMA inline male to RPTNC bulkhead

female)

Quick Setup for systems using the AW5800m Module:

1. Attach a 5800MHz antenna to each module. (see AW5-5800, AW23-5800)

2. Apply power to the AW5800m module.

3. Connect an Ethernet cable from each AW5800m to a network device.

4. Send Ethernet traffic. For troubleshooting see page 2.

Each AW5800m radio automatically selects the best radio channel, encrypts the Ethernet

traffic and transports the data wirelessly to its mate.

Any Ethernet device can be

connected to the AW5800m. The

AW5800m functions in place of an

Ethernet cable and provides a

transparent wireless point to point

Ethernet cable replacement. Cross-

over cables are not necessary as the

AW5800m automatically senses the

device (client or switch).

AW5800m-S

Ethernet

RJ45

Power

5.8GHz

Radio

Ethernet

Bridge

AW5800

Ethernet

RJ45

Power

Summary of content (7 pages)

PAGE 1
AW5800m-SR Module Integrator’s Kit User’s Manual Thank you for your purchase of the AW5800m-SR Module. If you have any questions when configuring your AvaLAN module please send us an email: support@avalanwireless.com Kit Contents: 2 AW5800m-SR RF Modules (RPSMA female) 2 AWP12 12in Pigtails (RPSMA inline male to RPTNC bulkhead female) Quick Setup for systems using the AW5800m Module: 1. 2. 3. 4. Attach a 5800MHz antenna to each module. (see AW5-5800, AW23-5800) Apply power to the AW5800m module.
PAGE 2
Application diagram: 40 Mile wireless network surveillance camera 1.536 Mb/sec System Diagram: Antenna Up to 50 Miles Antenna RF RF AW5800m-SR AW5800m-SR Power Power Ethernet 10BT Ethernet 10BT Power, Data, DIPs, LEDs and RF Interfaces: DIP Switch 8 Pin DIP LED Display 16 LEDs Power Jack P5/2.1mm Center Positive 4.
PAGE 3
LED display: The AW5800m has a 16 LED display to display the status of the device. LED 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Name Power RF TX RF RX Eth Link 1 (channel) 2 (channel) 4 (channel) 8 (channel) 16 (channel) 32 (channel) Function Unit has power and has successfully booted. Radio transmission is occurring. Radio reception is occurring. The Ethernet Port has a valid Ethernet connection By adding the values that are lit, the user can determine the current radio channel.
PAGE 4
Advanced Settings: Automatic frequency selection mode (DIP switches – all OFF for automatic mode) The AW5800m is designed to automatically select and continuously optimize the performance of its radio channel. The radio channel is monitored to ensure it is providing low error rates necessary for successful radio transmission. In the event that the error rate rises, the AW5800m will autonomously change to a new channel. There are 58 non-overlapping channels.
PAGE 5
Technical Specifications: (typical) Characteristic Specification - description RF transmission rate: 1.536 Mb/s Ethernet Throughput: 1.
PAGE 6
Appendix A: Agency Certifications FCC Certification The AW5800m OEM RF Module complies with Part 15 of the FCC rules and regulations. Compliance with labeling requirements, FCC notices and antenna regulations is required. Labeling Requirements In order to inherit AvaLAN’s FCC Certification, compliance requires the following be stated on the device: Contains FCC ID: R4N-AW5800M The enclosed device complies with Part 15 of the FCC Rules.
PAGE 7
FCC-Approved Antennas (5800MHz) Fixed Base Station and Mobile Applications AvaLAN Modules are pre-FCC approved for use in fixed base station and mobile applications. When the antenna is mounted at least 20 cm (8”) from nearby persons, the application is considered a mobile application. Portable Applications and SAR Testing When the antenna is mounted closer than 20 cm to nearby persons, then the application is considered “portable” and requires an additional test be performed on the final product.