User's Manual

Advanced Settings:
Automatic frequency selection mode (DIP switches – all OFF for automatic mode)
The AW5800m is designed to automatically select and continuously optimize the performance of its
radio channel. The radio channel is monitored to ensure it is providing low error rates necessary for
successful radio transmission. In the event that the error rate rises, the AW5800m will autonomously
change to a new channel. There are 58 non-overlapping channels.
Manual frequency selection mode
This mode enables the user to restrict the operation of the AW5800m to a specific channel. This can
be done by setting DIP switches 3-8 as shown in the table below.
DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8
Add 1 Add 2 Add 4 Add 8 Add 16 Add 32
0
1
x
5728.1250 Mhz
2 x 5730.2083 Mhz
3 x x 5732.2917 Mhz
4 x 5734.3750 Mhz
5 x x 5736.4583 Mhz
6 x x 5738.5417 Mhz
7 x x x 5740.6250 Mhz
8 x 5742.7083 Mhz
9 x x 5744.7917 Mhz
10 x x 5746.8750 Mhz
11 x x x 5748.9583 Mhz
12 x x 5751.0417 Mhz
13 x x x 5753.1250 Mhz
14 x x x 5755.2083 Mhz
15 x x x x 5757.2917 Mhz
16 x 5759.3750 Mhz
17 x x 5761.4583 Mhz
18 x x 5763.5417 Mhz
19 x x x 5765.6250 Mhz
20 x x 5767.7083 Mhz
21 x x x 5769.7917 Mhz
22 x x x 5771.8750 Mhz
23 x x x x 5773.9583 Mhz
24 x x 5776.0417 Mhz
25 x x x 5778.1250 Mhz
26 x x x 5780.2083 Mhz
27 x x x x 5782.2917 Mhz
28 x x x 5784.3750 Mhz
29 x x x x 5786.4583 Mhz
30 x x x x 5788.5417 Mhz
31 x x x x x 5790.6250 Mhz
32 x 5792.7083 Mhz
33 x x 5794.7917 Mhz
34 x x 5796.8750 Mhz
35 x x x 5798.9583 Mhz
36 x x 5801.0417 Mhz
37 x x x 5803.1250 Mhz
38 x x x 5805.2083 Mhz
39 x x x x 5807.2917 Mhz
40 x x 5809.3750 Mhz
41 x x x 5811.4583 Mhz
42 x x x 5813.5417 Mhz
43 x x x x 5815.6250 Mhz
44 x x x 5817.7083 Mhz
45 x x x x 5819.7917 Mhz
46 x x x x 5821.8750 Mhz
47 x x x x x 5823.9583 Mhz
48 x x 5826.0417 Mhz
49 x x x 5828.1250 Mhz
50 x x x 5830.2083 Mhz
51 x x x x 5832.2917 Mhz
52 x x x 5834.3750 Mhz
53 x x x x 5836.4583 Mhz
54 x x x x 5838.5417 Mhz
55 x x x x x 5840.6250 Mhz
56 x x x 5842.7083 Mhz
57 x x x x 5844.7917 Mhz
58 x x x x 5846.8750 Mhz
AUTO MODE
Channel # Tx Frequency
Site survey mode (DIP switch 2 - default is OFF for normal operation)
In this mode the AW5800m can perform a site survey. With this mode activated the radios send and
receive at 100% capacity by transceiving self-generated simulated data. The installer can monitor the
Link Quality display to assess channel quality while optimizing antennae orientation. The installer
can manually select each channel to evaluate performance and identify the best channels for
operation. By identifying channels with poor performance it is possible to identify possible interferers
and use “manual frequency selection mode” to avoid portions of the band or select a fixed operating
frequency. Important note: Ethernet traffic does not get transported while the radios are in this
mode.
LED Display mode (DIP switch 1 - default is OFF for normal LED display)
In this mode the display LEDs of the Master unit can be turned off for low power applications (solar).