Avalue Intelligent Display & System AID-173SHR All-In-One Bedside Terminal Quick Reference Guide 1st Ed- 07 December 2011 Copyright © 2011 Avalue Technology Inc., All Rights Reserved .
AID-173SHR Quick Reference Guide Federal Communication Commission Interference Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules.
AID-173SHR Quick Reference Guide FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
AID-173SHR Quick Reference Guide CONTENT 1. AID-173SHR Bedside Terminal Features ....................................................... 5 1.1 Front view .......................................................................................... 6 1.2 Rear & Bottom view .......................................................................... 7 1.3 Handset.............................................................................................. 8 2. Setting-up AID-173SHR Bedside Terminals .............
AID-173SHR Quick Reference Guide 1. AID-173SHR Bedside Terminal Features ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ In this chapter, you will get to know all features of our AID-173SHR bedside terminal. 1.1 Front view 1.2 Rear & Bottom view 1.
AID-173SHR Quick Reference Guide 1.1 Front view Magnetic Stripe Reader 17.
AID-173SHR Quick Reference Guide 1.
AID-173SHR Quick Reference Guide 1.3 Handset Barcode Scanner Scan button Volume Key Descriptions Activate the phone software (i.e.
AID-173SHR Quick Reference Guide 2. Setting-up AID-173SHR Bedside Terminals ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ This chapter gives instructions on how to set up AID-173SHR bedside terminal hardware and how to connect different cables. Furthermore, with provided Internet ISP setting information, you will be able to connect AID-173SHR bedside terminal to the Internet. 2.1 Mounting 2.2 Cabling 2.3 System Activation & Registration 2.
AID-173SHR Quick Reference Guide 2.
AID-173SHR Quick Reference Guide 2.2 Cabling 1. Power Cable 2. Ethernet (RJ-45) Cable (Optional) 3. TV (Coaxial) Cable (Optional) Coaxial connector Ethernet (RJ-45) Connector Power Jack Please follow below steps to connect power cable to system.
AID-173SHR Quick Reference Guide 2.3 System Activation & Registration 1. Upon receiving your product, a system activation and software registration needs be performed before you start using this system. 2. Please consult your local service providers for more details.
AID-173SHR Quick Reference Guide 2.4 Connecting to the Internet 1. Use built-in wireless LAN to connect to the Internet. 2. Use Ethernet (RJ-45) to connect to the Internet. 3. Consult your Internet Service Provider (ISP) for software settings. Note: ISP, IP, (wireless) router, Access Point, DSL modem, Access ID & Password, and so on, are needed for Internet access.
AID-173SHR Quick Reference Guide 3. Using AID-173SHR Bedside Terminals ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ This chapter describes in detail all features of AID-173SHR bedside terminal. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.
AID-173SHR Quick Reference Guide 3.1. Turn ON/OFF the System ON/OFF Touch Button 3.1.1 Turn ON the System 1. 2. 3. 4. Check if the Power ON/OFF LED light is red. Move your finger to touch the Power ON/OFF icon. The Power ON/OFF LED turns green. Your system is turned ON. 3.1.2 Turn OFF the System 1. Move your finger to touch the Power ON/OFF icon for about 4 seconds. 2. The Power ON/OFF LED turns red. 3. Your system is turned OFF.
AID-173SHR Quick Reference Guide 3.2 Using LCD Display and Touch Screen Control Buttons 3.2.1 Adjust System Volume 1. Move your finger on the top of the Volume Up or Volume Down icon. 2. The volume will be adjusted accordingly. 3.2.2 Adjust LCD Display Brightness 1. Move your finger on the top of the Brightness Up or Brightness Down icon. 2. The brightness of the LCD display will be adjusted accordingly. 3.2.3 Using Touch Screen 1. To select the item on the touch screen, press the item once. 2.
AID-173SHR Quick Reference Guide 3.3 Using Earphone and Microphone 1. Open the rubber cover on the right side of the system. 2. Insert the earphone phone or microphone into the jacks.
AID-173SHR Quick Reference Guide 3.4 Using the Smart Card Reader 1. Have the IC card face up. 2. Insert the IC card into the Smart Card Reader slot.
AID-173SHR Quick Reference Guide 3.5 Using Magnetic Stripe Reader 1. Have your card with the magnetic stripe facing outside. 2. Slide the card from top to the bottom.
AID-173SHR Quick Reference Guide 3.6 Using RFID Reader/Writer 1. Place the card onto the RFID Reader/Writer. Keep card close to the reader no greater than 5cm. 2. The RFID will beep if the card is read or written successfully. Note: The RFID Reader/Writer accepts ISO 14443A standard cards ONLY. Optional RFID Reader/Writer accepts ISO 14443A/14443B/15693 cards.
AID-173SHR Quick Reference Guide 3.7 Using Handset Pick up the Handset 1. Lift the handset from the cradle to start usage. Hang up the Handset 2. Return the handset back to the handset cradle with keypad facing inside.
AID-173SHR Quick Reference Guide Start and End a Phone Conversation 1. To make a phone call, enter the numbers by keying the numbers on the keypad and press “Dial” icon. 2. To end a phone conversation, press the “Hang Up” icon. 3. Use the volume control to adjust the volume of the handset. Note: Phone application software and Internet connection are required.
AID-173SHR Quick Reference Guide 3.8 Using Barcode Scanner 1. Pick up the handset and directed to the object with the Scan button facing up. 2. Aim to the barcode and maintain an appropriate distance between barcode and scanner. 3. Press SCAN button. 4. The Barcode Scanner will “Beep” when the barcode is successfully read.
AID-173SHR Quick Reference Guide 4. Upgrading AID-173S Bedside Terminals ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ In this chapter, you will learn several peripherals upgrade or replacement. Please perform these steps with care. ▲ WARNING: Turn OFF the system and disconnect the power cable before performing the following tasks. ▲CAUTION: Only a certified service technician is authorized to remove the cover and access system components. 4.1 4.2 4.3 4.4 4.
AID-173SHR Quick Reference Guide 4.1 Adding/Removing/Replacing Memory 1. Remove the two screws from the service door. 2. Open the service door. 1. Press the two latches of the retaining clips locking the memory module. 2. The memory module will pop up at an angle. 3. Lift the memory module from the memory socket. 1. Properly align the memory module to the connector edge. 2. Slide the memory module into the memory socket. 3. Push the memory module down until locked by the clip latches 4.
AID-173SHR Quick Reference Guide 4.2 Adding/Removing/Replacing TV Tuner 1. Remove the two screws from the service door. 2. Open the service door. 1. 2. 3. Unplug the TV signal cable. Unlock the mini-PCIe socket. Pull the TV module out of the socket. 1. Place the TV module into the mini-PCIe socket. 2. Lock the mini-PCIe socket. 3. Connect the TV signal cable to the TV module. 4. Close the service door. 5. Lock the service door by means of two screws.
AID-173SHR Quick Reference Guide 4.3 Removing and Replacing the Wireless Card 1. Remove the two screws from the service door. 2. Open the service door. 1. Unplug the two antennas from the wireless module. 2. Unlock the mini-PCIe socket. 3. Pull the wireless module out of the socket. 1. Place the wireless module into the mini-PCIe socket. 2. Lock the mini-PCIe socket. 3. Connect the two antennas to the wireless module. 4. Close the service door. 5. Lock the service door by means of two screws.
AID-173SHR Quick Reference Guide 4.4 Adding 3rd Party Mini-PCIe Cards 1. Remove the two screws from the service door. 2. Open the service door. 1. Insert the 3rd party mini-PCIe card into the empty mini-PCIe expansion socket. 2. Lock the mini-PCIe socket. Close the service door by means of two screws.
AID-173SHR Quick Reference Guide 4.5 Removing and Replacing the Hard Disk Drive 1. Remove the two screws from the service door. 2. Open the service door. 1. Remove two screws from the hard disk slot to release hard disk. 2. Disconnect power and data cables from the hard disk drive. 3. Pull the top of the hard disk bracket and remove the hard disk drive from the slot. Remove the two screws from the hard disk bracket.
AID-173SHR Quick Reference Guide 1. Attach hard disk to bracket by means of two screws. 2. Place the hard disk drive into the slot. 3. Attach hard disk bracket to slot by means of two screws. 4. Connect the power and data cable to the hard disk drive. 5. Close the service door by means of two screws.
AID-173SHR Quick Reference Guide Thank you for purchasing and using AID-173SHR Bedside Terminals. We hope you have a joyful experience with our products and services.
