EBM-CDV 5.25” Intel Cedarview Atom Mini Module User’s Manual 4th Ed – 09 July 2014 Part No.
EBM-CDV User’s Manual FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
User’s Manual Content 1. Getting Started ............................................................................................................ 6 1.1 Safety Precautions .................................................................................................... 6 1.2 Packing List ............................................................................................................... 6 1.3 Document Amendment History .......................................................................
EBM-CDV User’s Manual 2.3.27 AMPLIFIER_L1 (AMP_L1) ......................................................................................................... 34 2.3.28 VGA connector (JVGA1) ............................................................................................................ 34 2.3.29 LPC connector (JLPC1) ............................................................................................................. 35 2.3.30 SPI connector (JSPI1) .................................
User’s Manual 3.6.6.2 Discard Changes and Exit ..................................................................................................... 71 3.6.6.3 Save Changes and Reset ...................................................................................................... 72 3.6.6.4 Discard Changes and Reset .................................................................................................. 72 3.6.6.5 Save Changes ...........................................................
EBM-CDV User’s Manual 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
User’s Manual 1.
EBM-CDV User’s Manual 1.4 Manual Objectives This manual describes in details Avalue Technology EBM-CDV Single Board. We have tried to include as much information as possible but we have not duplicated information that is provided in the standard IBM Technical References, unless it proved to be necessary to aid in the understanding of this board. We strongly recommend that you study this manual carefully before attempting to set up EBM-CDV series or change the standard configurations.
User’s Manual 1.5 System Specifications System CPU Onboard Intel Cedarview-M / Cedarview-D DC (Co-layout) N2800/D2550 BIOS AMI 16M-bit SPI BIOS System Chipset Intel NM10 Express Chipset I/O Chip E/C IT8518E System Memory one 204-pin DDR3 800/1066 SODIMM supports up to 4GB (Single channel) SSD Watchdog Timer One CompactFlash Type I/II socket Reset: 1 ~255 min. and 1 sec. or 1 min./step H/W Status Monitor Monitoring system temperature, voltage, and cooling fan status.
EBM-CDV User’s Manual Realtek ALC892 supports 5.1 CH Audio HD Codec Audio Interface Line out, Speak out (2W) connector & pin Jaudio 2x6 header (Line in, Line out & Mic in), headset 3x2 pin header Ethernet LAN Chip Dual Intel 82574L PCI-E Gigabit LAN Ethernet Interface 10/100/1000 Base-Tx Fast Ethernet compatible Touch Chipset Touch Interface EETI ETP-CP-S458XRU support 4, 5 wire USB (4), With 5-pin 2.
User’s Manual Cedarview-D 1920 x 1200 60 Hz Edge placement must be the same as EBM-PNV except VGA is placed by HDMI.
EBM-CDV User’s Manual 1.6 Architecture Overview—Block Diagram The following block diagram shows the architecture and main components of EBM-CDV.
User’s Manual 2.
EBM-CDV User’s Manual 2.
User’s Manual 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
EBM-CDV User’s Manual USB_PWR_SEL1 USB Power select 3 x 1 header, pitch 2.00mm Connectors Label CF1 COM1 CPU_FAN SODIMM1 AUD1 JBKL1 JBKL2 Function Compact Flash card connector Serial Port 1 connector CPU fan connector 204-pin DDR3 SODIMM socket Audio connector LCD Inverter connector LCD Inverter connector Note COM2 COM3 COM4 COM5 COM6 DIO1 JLED1 LED2 JLVDS1 JLVDS2 Serial Port 2 connector Serial Port 3 connector Serial Port 4 connector Serial Port 5 connector 5 x 2 wafer, pitch 2.
User’s Manual SATA2 Serial ATA connector 2 SIM1 HDMI1 HP_OUT1 JVGA1 SIM card slot HDMI connector Handphone_out connector VGA connector 8 x 2 wafer, pitch 2.
EBM-CDV User’s Manual 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* Clear CMOS * Default 2.3.
User’s Manual 2.3.3 SATA Power select (JP3) * Default 2.3.
EBM-CDV User’s Manual 2.3.5 Multi-function select (SW2) 2.3.
User’s Manual 2.3.7 LCD backlight brightness adjustment (JVR1) Signal PIN +5V 1 VBRIGHT 2 GND 3 * Default Variation Resistor (Recommended: 4.7KΩ, >1/16W) Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by JBKL1. Please see the JBKL1 section for detailed circuitry information.
EBM-CDV User’s Manual 2.3.8 Handset Speaker Out selector (JHS1) * Default 2.3.
User’s Manual 2.3.10 Power connector (PWR2) 2.3.
EBM-CDV User’s Manual 2.3.12 LCD Inverter connector (JBKL1) Signal PIN +5V 5 VBRIGHT 4 BKLEN 3 GND 2 +12V 1 Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by JVR1. Please see the JVR1 section for detailed circuitry information.
User’s Manual 2.3.13 LCD Inverter connector (JBKL2) 2.3.
EBM-CDV User’s Manual 2.3.15 Serial port 2 connector (COM2) Signal 2.3.
User’s Manual 2.3.
EBM-CDV User’s Manual 2.3.
User’s Manual 2.3.
EBM-CDV User’s Manual 2.3.
User’s Manual 2.3.21 Touch panel connector (JTOUCH) Signal PIN UL 1 UR 2 PROBE 3 LR 4 LL 5 NOTE: Under 4W situation UL=X+, UR=Y+, LR=Y-, LL=X- 2.3.
EBM-CDV User’s Manual 2.3.23 2.3.
User’s Manual 2.3.25 Audio connector (AUD1) Signal 2.3.
EBM-CDV User’s Manual 2.3.27 2.3.
User’s Manual 2.3.29 LPC connector (JLPC1) Signal 2.3.
EBM-CDV User’s Manual 2.3.31 EC_Program (EC_SPI1) Signal 2.3.
User’s Manual 3.
EBM-CDV User’s Manual 3.1 Introduction The BIOS setup program allows users to modify the basic system configuration. In this following chapter will describe how to access the BIOS setup program and the configuration options that may be changed. 3.2 Starting Setup The AMI BIOS™ is immediately activated when you first power on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it.
User’s Manual 3.3 Using Setup In general, you use the arrow keys to highlight items, press to select, use the PageUp and PageDown keys to change entries, press for help and press to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard.
EBM-CDV User’s Manual 3.4 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press or the F1 key again. 3.5 In Case of Problems If, after making and saving system changes with Setup, you discover that your computer no longer is able to boot, the AMI BIOS supports an override to the CMOS settings which resets your system to its defaults.
User’s Manual 3.6 BIOS setup Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and exit choices. Use the arrow keys to select among the items and press to accept and enter the sub-menu. 3.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock. 3.6.1.1 System Language Use this option to select system language 3.6.1.
EBM-CDV User’s Manual 3.6.2 Advanced BIOS settings This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus. Item Launch PXE OpROM Launch Storage OpROM Options Disabled, Enabled[Default] Disabled, Enabled[Default] 3.6.2.1 PCI Subsystem Settings 42 EBM-CDV User’s Manual Description Enable or disable Boot Option for Legacy Network Devices Enable or disable Boot Option for Legacy Mass storage devices With Option ROM.
User’s Manual Item PCI Latency Timer VGA Palette Snoop PERR# Generation SERR# Generation Options 32 PCI Bus Clocks[Default] 64 PCI Bus Clocks 96 PCI Bus Clocks 128 PCI Bus Clocks 160 PCI Bus Clocks 192 PCI Bus Clocks 224 PCI Bus Clocks 248 PCI Bus Clocks Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Description Value to be programmed into PCI Latency Timer Register. Enables or Disables VGA Palette registers Snooping.
EBM-CDV User’s Manual Disabled[Default] Enabled Disabled[Default], Enabled S3 video Repost DeepS5 Enable or Disable S3 video repost Enter DeepS5. 3.6.2.3 S5 RTC Wake settings Item Options Wake system with Fixed Time Disabled[Default], Enabled Wake system with Dynamic Disabled[Default], Time 44 EBM-CDV User’s Manual Enabled Description Enables or Disables wake on alarm event. When enabled, System will wake on the hr::min::sec specified. Enables or Disables wake on alarm event.
User’s Manual 3.6.2.4 CPU Configuration Use the CPU configuration menu to view detailed CPU specification and configure the CPU. Item Options Description Hyper-Threading Disabled[Default], Enabled This item allows you to enable or disable Execute Disable Bit Disabled[Default], Enabled This item allows you to enable or disable the Limit CPUID Maximum Disabled[Default], Enabled This item allows you to limit CPUID maximum Intel® Hyper Threading technology. No-Execution page protection technology.
EBM-CDV User’s Manual 3.6.2.5 Thermal Configuration 3.6.2.5.1 CPU Thermal Configuration Item DTS SMM Options Enabled Disabled[Default] Critical Temp reporting (Out of Spec) 46 EBM-CDV User’s Manual Description Disabled: ACPI thermal management uses EC reported temperature values. Enabled: ACPI thermal management uses DTS SMM mechanism to obtain CPU temperature values. Out of spec: ACPI thermal management uses EC reported temperature values and DTS SMM is used to handle Out of spec condition.
User’s Manual 3.6.2.5.2 Platform Thermal Configuration Item Critical Trip Point Active Trip Point Lo Fan Speed Active Trip Point Hi Fan Speed Passive Trip Point Options POR[Default] 15C 23C 31C 39C 47C 55C 63C 71C 79C 87C 95C 103C 111C 119C 127C Disabled 15C 23C 31C 39C 47C 55C 63C 71C 79C 87C 95C 103C 111C 119C Description This value controls the temperature of the ACPI Critical Trip Point – the point in which the OS will shut the sytem off.
EBM-CDV User’s Manual Passive TC1 Value 1 – 16 This value sets the TC1 -2 value for the ACPI Passive Cooling Formula. Range 1 - 16 2 - 32 This item sets the TSP value for the ACPI Passive Cooling Formula. It represents in tenths of a second how often the OS will read the temperature when passive cooling is enabled Range 2- 32 Options Description Passive TC2 Value Passive TSP Value 3.6.2.
User’s Manual 3.6.2.7 Intel Fast Flash Standby Item Options iFFS Support Enabled Disabled[Default] Description Enable or Disable iFFS 3.6.2.8 USB Configuration The USB configuration menu is used to read USB configuration information and configure USB.
EBM-CDV User’s Manual Item Options Legacy USB support Enabled[Default] Disabled Auto ECHI Hand-off Enabled Disabled[Default] USB transfer time-out Device reset time-out Device power-up delay Generic STORAGE DEVICE 9407 3.6.2.9 1sec / 5sec 10sec / 20sec[Default] 10sec / 20sec[Default] 30sec / 40sec Auto[Default] Manual Auto Floppy Forced FDD Hard Disk CD-ROM Description Enables Legacy USB support. AUTO disables legacy support if no USB devices are connected.
User’s Manual 3.6.2.9.1 Smart Fan Mode Configuration Item CPU Smart Fan Mode Fan PWM Option Manual Mode[Default] Mode 01-20 0 - 255 Description CPU Smart Fan Mode Select Fan PWM duty 3.6.2.10 Smart settings Item Options SMART Self Test Enabled[Default] Disabled Description Run SMART Self Test on all HDDs during POST.
EBM-CDV User’s Manual 3.6.2.11 Second Super IO Configuration You can use this item to set up or change the Second Super IO configuration for FDD controllers, parallel ports and serial ports. Please refer to 3.6.2.9.1-4 for more information.
User’s Manual 3.6.2.11.1 Serial Port 1 Configuration Item Serial Port Change Settings Option Enabled, Disabled[Default] Auto[Default] IO=3F8h; IRQ=3, IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12 Description Enable or Disable Serial Port (COM) Select an optimal setting for Super IO device. 3.6.2.11.
EBM-CDV User’s Manual Item Serial Port Change Settings Option Enabled, Disabled[Default] Auto[Default] IO=2F8h; IRQ=3, IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12 Description Enable or Disable Serial Port (COM) Select an optimal setting for Super IO device. 3.6.2.11.
User’s Manual 3.6.2.11.4 Serial Port 4 Configuration Item Serial Port Change Settings Option Enabled, Disabled[Default] Auto[Default] IO=2E8h; IRQ=3, IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2F0h; IRQ=3,4,5,6,7,9,10,11,12 IO=2E0h; IRQ=3,4,5,6,7,9,10,11,12 Description Enable or Disable Serial Port (COM) Select an optimal setting for Super IO device.
EBM-CDV User’s Manual 3.6.2.12 Super IO Configuration You can use this item to set up or change the Super IO configuration for FDD controllers, parallel ports and serial ports. Please refer to 3.6.2.10.1 and 3.6.2.10.2 for more information. Item Watch Dog PWRON After PWR-Fail 56 EBM-CDV User’s Manual Option Disabled[Default] 30sec 40sec 50sec 1min 2min 10min 30min Off[Default] On Former-Sts Description Select WatchDog. Select PWRON After PWR-Fail.
User’s Manual 3.6.2.12.1 Serial Port 0 Configuration Item Serial Port Change Settings Device Mode Option Disabled[Default] Enabled, Auto[Default] IO=3F8h; IRQ=4, IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12 Normal[Default] High Speed Description Enable or Disable Serial Port (COM) Select an optimal setting for Super IO device. Change the Serial Port mode.
EBM-CDV User’s Manual 3.6.2.12.2 Serial Port 1 Configuration Item Serial Port Change Settings Option Disabled[Default] Enabled, Auto[Default] IO=2F8h; IRQ=3, IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12 IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12 IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12 Device Mode 58 EBM-CDV User’s Manual Normal[Default] High Speed Description Enable or Disable Serial Port (COM) Select an optimal setting for Super IO device. Change the Serial Port mode.
User’s Manual 3.6.2.13 PPM configuration Item EIST CPU C state Report Enhanced C state CPU Hard C4E CPU C6 state Option Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled C4 Exit Timing Default[Default] Fast Slow C-state POPDOWN Disabled[Default] Enabled C-state POPUP Disabled[Default] Enabled Description Enable/Disable Intel SpeedStep. Enable/Disable CPU C state report to OS. Enable/Disable Enhanced CPU C state.
EBM-CDV User’s Manual 3.6.3 Advanced Chipset Features Item Description Host Bridge Host Bridge Parameters South Bridge South Bridge Parameters 3.6.3.
User’s Manual 3.6.3.1.1 Host Bridge Item Memory Frequency and Timing Intel IGD Configuration 3.6.3.1.1.1 Description Config Memory Frequency and Timing Settings. Config Intel IGD Settings.
EBM-CDV User’s Manual Item VBIOS Version IGFX – Boot Type Panel Scaling Active LFP CH7511 EDID Panel Option LVDS Back Light PWM LVDS Back Light PWM Frequency IGD Clock Source 62 EBM-CDV User’s Manual Option 1053 1059 1071[Default] VBIOS Default[Default] CRT CRT + LVDS CRS + HDMI (Twin) LVDS LVDS + CRT HDMI HDMI + LVDS Auto[Default] Force Scaling Off Maintain Aspect Ratio No LVDS LVDS[Default] 1024x768 24/1 [Default] 800x600 18/1 1024x768 18/1 1366x768 18/1 1024x600 18/1 1280x800 18/1 1920x1200 24
User’s Manual Fixed Graphics Memory Size 128MB[Default] 256MB ALS Support Disabled[Default] Enabled 3.6.3.1.1.2 Configure Fixed Graphics Memory Size Valid only for ACPI. Legacy=ALS Support through the IGD INT10 function. ACPI=ALS support through an ACPI ALS driver. Memory Frequency and Timing Item MRC Fast Boot Max TOLUD Option Disabled Enabled[Default] Dynamic[Default] 1GB 1.25GB 1.5GB 1.75GB 2GB 2.25GB 2.5GB 2.75GB 3GB 3.25GB Description Enalbe or disable MRC fast boot. Maximum Value of TOLUD.
EBM-CDV User’s Manual 3.6.3.2 South bridge 3.6.3.2.1 PCI Express Root Port 0 Item PCI Express Port 0 Port 0 IOxAPIC Automatic ASPM 64 EBM-CDV User’s Manual Option Disabled Enabled[Default] Disabled[Default] Enabled Manual[Default] Auto Description Enable / Disable PCI Express Root Port 0.
User’s Manual ASPM L0s ASPM L1 Disabled[Default] Root Port Only End point Port Only Both Root And Endpoint Ports Disabled[Default] Enabled URR FER NFER CER CTO SEFE SENFE SECE PME SCI Hot Plug Extra Bus Reserved Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled Enabled[Default] Disabled[Default] Enabled 0-7 Reserved Memory 1 – 20MB Rese
EBM-CDV User’s Manual 66 EBM-CDV User’s Manual
User’s Manual Item PCI Express Port 0 Port 0 IOxAPIC Automatic ASPM ASPM L0s ASPM L1 URR Option Auto[Default] Enabled Disabled Enabled Disabled[Default] Manual[Default] Auto Disabled[Default] Root Port Only Endpoint Port Only Both Root And Endpoint Ports Enabled Disabled[Default] Enabled Disabled[Default] SENFE Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] Enabled Disabled[Default] SECE Enabled Disabled[Default] FER
EBM-CDV User’s Manual Extra Bus Reserved 0-7 Reserved Memory 1 – 20MB Reserved I/O 4K/8K/12K/16K/20K Extra Bus Reserved (0 -7)for bridges behind this Root Bridge. Reserved Memory and Prefetchable Memory (1-20MB) Range for this Root Bridge. Reserved I/O (4K/8K/12K/16K/20K) Range for this Root Bridge. 3.6.3.2.3 TPT Devices Item Azalia Controller Select USB Mode UHCI #1 (ports 0 and 1) UHCI #2 (ports 2 and 3) UHCI #3 (ports 4 and 5) UHCI #4 (ports 6 and 7) USB 2.
User’s Manual 3.6.4 Boot settings Item Setup Prompt Timeout Bootup NumLock State Quiet Boot Fast Boot Option 1~65535 On Off[Default] Enabled Disabled[Default] Enables or Disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options UPON REQUEST –GA20 can be disabled using BIOS services.
EBM-CDV User’s Manual 3.6.5 Security Use the Security menu to set system and user password. 3.6.5.1 Administrator Password This setting specifies a password that must be entered to access the BIOS Setup Utility. If only the Administrator's password is set, then this only limits access to the BIOS setup program and is only asked for when entering the BIOS setup program. By default, no password is specified. 3.6.5.
User’s Manual 3.6.6 Save & Exit 3.6.6.1 Save Changes and Exit Use the save changes and reset option to save the changes made to the BIOS options and to exit the BIOS configuration setup program. 3.6.6.2 Discard Changes and Exit Use the Discard changes and Exit option to exit the system without saving the changes made to the BIOS configuration setup program.
EBM-CDV User’s Manual 3.6.6.3 Save Changes and Reset Any changes made to BIOS settings are stored in NVRAM. The setup program then exits and reboots the controller. 3.6.6.4 Discard Changes and Reset Any changes made to BIOS settings during this session of the BIOS setup program are discarded. The setup program then exits and reboots the controller. 3.6.6.5 Save Changes Changes made to BIOS settings during this session are committed to NVRAM. The setup program remains active, allowing further changes. 3.
User’s Manual 4. Drivers Installation Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen.
EBM-CDV User’s Manual 4.1 Install VGA Driver Insert the Supporting DVD-ROM to DVD-ROM drive, click on “start” icon and it should show the index page of Avalue’s products automatically. If not, locate the folder HTML and choose the product from the targeted folder. Note: The installation procedures and screen shots in this section are based on W7 operating system. Step 1. Locate 「\VGA\EBM-CDV_VGA」. Step 4. Select Next to continue installation. Step 5. Select Install to continue installation. Step 2.
User’s Manual Step 7.
EBM-CDV User’s Manual 4.2 Install Chipset Driver (Cedarview) Insert the Supporting DVD-ROM to DVD-ROM drive, click on “start” icon and it should show the index page of Avalue’s products automatically. If not, locate the folder HTML and choose the product from the targeted folder. Note: The installation procedures and screen shots in this section are based on W7 operating system. Step 1. Locate 「\Driver_Chipset\Intel\EBM-C DV-INF」. Step 4. Select Next to continue installation. Step 2.
User’s Manual 4.3 Install Audio Driver (For Realtek ALC892) Insert the Supporting DVD-ROM to DVD-ROM drive, click on “start” icon and it should show the index page of Avalue’s products automatically. If not, locate the folder HTML and choose the product from the targeted folder. Note: The installation procedures and screen shots in this section are based on W7 operating system. Step 2. Select Next to the next step. Step 1. Locate 「\Driver_Audio\Realtek\ALC892\EBM-CDV-audio」. Step 3. Installing.
EBM-CDV User’s Manual 4.4 Install Ethernet Driver (For Realtek 82574L) Insert the Supporting DVD-ROM to DVD-ROM drive, click on “start” icon and it should show the index page of Avalue’s products automatically. If not, locate the folder HTML and choose the product from the targeted folder. Note: The installation procedures and screen shots in this section are based on W7 operating system. Step 3. Click Next. Step 1. Locate 「\Driver_Gigabit\Intel\82574L\EBM-CDV-LAN」 Step 4.
User’s Manual Step 6. Click Install to begin installation Step 8. Click Finish to complete installation Step 7. Wait while installing.
EBM-CDV User’s Manual 5.
User’s Manual Unit: mm EBM-CDV User’s Manual 81
EBM-CDV User’s Manual Unit: mm 82 EBM-CDV User’s Manual
