EBM-PNV (B.2) Intel® Atom™ Dual-Core 5.25” Mini Module with Intel® ICH8-M Chipset Quick Installation Guide 3rd Ed – 20 December 2011 Part No.
EBM-PNV (B.2) Quick Installation Guide Content 1. Getting Started ............................................................................................................ 3 1.1 Safety Precautions .................................................................................................... 3 1.2 Packing List ............................................................................................................... 3 2. Hardware Configuration ...................................................
Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EBM-PNV (B.2) Quick Installation Guide 2. Hardware Configuration 2.1 Product Overview 4 EBM-PNV (B.
Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
EBM-PNV (B.2) Quick Installation Guide Connectors Label BAT CFCARD COM1 CPU_FAN DIMM JAUDIO JBKL1 JBKL2 JCOM2 Function Battery connector Compact Flash card connector Serial Port 1 connector CPU fan connector 204-pin DDR3 SODIMM socket Audio connector LCD Inverter connector LCD Inverter connector Serial Port 2 connector Note 2 x 1 wafer, pitch 1.
Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT) Protect* Clear CMOS * Default 2.3.2 Multi-function select (SW1) ON OFF 1 AT SEL ATX SEL 2 CF Master CF Slave 3 Touch Off Touch On 4 Touch: 4W Touch: 5W 5 GPIO32:L GPIO32:H 6 GPIO33:L GPIO33:H EBM-PNV (B.
EBM-PNV (B.2) Quick Installation Guide 2.3.3 Serial port 1/ 2 - RS-232/ 422/ 485 mode select (SW2) In Serial Port 1 mode RS-232 RS-422 RS-485 1 ON OFF OFF 2 OFF ON OFF 3 OFF OFF ON In Serial Port 2 mode 2.3.4 RS-232 RS-422 RS-485 4 ON OFF OFF 5 OFF ON OFF 6 OFF OFF ON Serial port 1/ 2 pin9 signal select (JRI1/ JRI2) Ring* JRI2 JRI1 +12V +5V * Default 8 EBM-PNV (B.
Quick Installation Guide 2.3.5 Serial port 1/ 2 RS-232/ 422/ 485 mode select (JP1/ JP2) RS-232* JP2 JP1 RS-422/ 485 * Default 2.3.6 SATA DOM Pin 7 Power mode selector (JP4) Clear* Power Signal PIN SATA_PWR 1 GND#7_1 2 GND 3 * Default EBM-PNV (B.
EBM-PNV (B.2) Quick Installation Guide 2.3.7 2.3.8 Handset speaker Mode selector (JHS) Signal PIN PIN Signal HS_MIC+ 1 2 HS_MIC- HS_OUT+ 3 4 GND HOOK 5 6 GND Battery connector (BAT) 10 EBM-PNV (B.
Quick Installation Guide 2.3.9 LCD backlight brightness adjustment (JVR1) Mode1: VR type Mode 2: DC type* * Default Signal PIN PIN Signal +5V 1 2 DC VR 3 4 VR GND 5 6 PWM Note: DC: 0V ~5V Mode 3: Pulse-Width Modulated type Variation Resistor (Recommended: 4.7KΩ, >1/16W) Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by JBKL1. Please see the JBKL1 section for detailed circuitry information.
EBM-PNV (B.2) Quick Installation Guide 2.3.10 LCD backlight brightness adjustment (JVR2) Mode1: VR type Mode 2: DC type* * Default Note: DC: 0V ~5V Signal PIN PIN Signal +5V 1 2 DC2 VR 3 4 VR GND 5 6 PWM2 Mode 3: Pulse-Width Modulated type Variation Resistor (Recommended: 4.7KΩ, >1/16W) Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by JBKL2.
Quick Installation Guide 2.3.11 2.3.12 Power connector (PWR2) Signal PIN PIN Signal VIN 4 3 VIN GND 2 1 GND Serial ATA power connector (S_PWR1) Signal PIN SATA_PWR 2 GND 1 EBM-PNV (B.
EBM-PNV (B.2) Quick Installation Guide 2.3.13 LCD Inverter connector (JBKL1/ JBKL2) Signal PIN +5V 5 BRIGHT 4 BLK_ON 3 GND 2 +12V 1 JBKL1 JBKL2 Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by JVR1/ JVR2. Please see the JVR1/ JVR2 section for detailed circuitry information. 2.3.13.1 Signal Description – LCD Inverter Connector (JBKL1/ JBKL2) Signal Signal Description BRIGHT Vadj = 0.75V ~ 4.
Quick Installation Guide 2.3.14 Optional LPT connector (PRINT) PRINT (Rear side) Signal PIN GND 20 GND 19 GND 18 SLIN# 17 PAR_INIT# 16 ERR# 15 AFD# 14 SLCT 13 PE 12 BUSY 11 ACK# 10 PTD7 9 PTD6 8 PTD5 7 PTD4 6 PTD3 5 PTD2 4 PTD1 3 PTD0 2 STB- 1 EBM-PNV (B.
EBM-PNV (B.2) Quick Installation Guide 2.3.15 Serial port 1 connector (COM1) In RS-232 Mode Signal PIN PIN Signal DCD1 1 2 RxD1 TxD1 3 4 DTR1 GND 5 6 DSR1 RTS1 7 8 CTS1 RI1 9 NC In RS-422 Mode Signal PIN PIN Signal TxD1- 1 2 RxD1+ TxD1+ 3 4 RxD1- GND 5 6 NC NC 7 8 NC NC 9 NC In RS-485 Mode Signal 16 EBM-PNV (B.
Quick Installation Guide 2.3.16 2.3.17 CPU fan connector (CPU_FAN) Signal PIN FAN_TAC1 3 +12V 2 GND 1 Audio connector (JAUDIO) Signal PIN PIN Signal APM_LOUT_R 1 2 APM_LOUT_L GND 3 4 GND LINEIN_R 5 6 LINEIN_L MIC-R 7 8 MIC-L FRONT-JD 9 10 LINE1-JD MIC1-JD 11 12 GND EBM-PNV (B.
EBM-PNV (B.2) Quick Installation Guide 2.3.18 Serial port 2 connector (JCOM2) In RS-232 Mode Signal PIN PIN Signal DCD2 1 2 RxD2 TxD2 3 4 DTR2 GND 5 6 DSR2 RTS2 7 8 CTS2 RI2 9 10 NC In RS-422 Mode Signal PIN PIN Signal TxD2- 1 2 RxD2+ TxD2+ 3 4 RxD2- GND 5 6 NC NC 7 8 NC NC 9 10 NC In RS-485 Mode Signal 18 EBM-PNV (B.
Quick Installation Guide 2.3.19 Serial port 3/ 4/ 5/ 6 connector (JCOM3/ JCOM4/ JCOM5/ JCOM6) JCOM3 JCOM4 JCOM5 JCOM3 JCOM6 Signal 2.3.
EBM-PNV (B.2) Quick Installation Guide 2.3.21 LED indicator connector (JLED) Signal 20 EBM-PNV (B.2) Quick Installation Guide PIN PIN Signal GND 1 2 +3.3V HD_ACT# 3 4 +3.3V LAN1_ACT 5 6 3.3V_SB LAN2_ACT 7 8 3.
Quick Installation Guide 2.3.22 LVDS connector (JLVDS1) Signal PIN PIN +5V 2 1 +5V 4 3 2 Signal +3.3V +3.3V 2 I C_DAT 6 5 I C_CLK GND 8 7 GND Txout0 10 9 Txout1 Txout0# 12 11 Txout1# GND 14 13 GND Txout2 16 15 NC Txout2# 18 17 NC GND 20 19 GND NC 22 21 NC NC 24 23 NC GND 26 25 GND NC 28 27 NC NC 30 29 NC GND 32 31 GND Txclk 34 33 NC Txclk# 36 35 NC GND 38 37 GND +12V 40 39 +12V 2.3.22.
EBM-PNV (B.2) Quick Installation Guide 2.3.23 LVDS connector (JLVDS2) Signal PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 +3.
Quick Installation Guide 2.3.24 Touch panel connector (JTOUCH) Signal PIN UL 1 UR 2 PROBE 3 LR 4 LL 5 NOTE: Under 4W situation UL=X+, UR=Y+, LR=Y-, LL=X- 2.3.25 USB connector 4&5, 2&3 (JUSB1/ JUSB2) JUSB2 JUSB1 Signal PIN PIN Signal +5V 1 2 GND D- 3 4 GND D+ 5 6 D+ GND 7 8 D- GND 9 10 +5V EBM-PNV (B.
EBM-PNV (B.2) Quick Installation Guide 2.3.26 2.3.27 USB connector 9 (JUSB4) Signal PIN +5V 1 D- 2 D+ 3 GND 4 GND 5 +3.3V 6 OSD for front panel key (JKEY) 24 EBM-PNV (B.
