ECM-CX700 3.5" VIA CX700M Eden V4 ULV 1GHz Micro Module Quick Installation Guide 5th Ed – 9 November 2011 To receive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.com.tw Copyright Notice Copyright 2011 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No.
ECM-CX700 Series Disclaimer Avalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance.
Quick Installation Guide Technical Support We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult the user’s manual first. To receive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.com.
ECM-CX700 Series Contents 1. Getting Started ............................................................................................................ 5 1.1 Safety Precautions .................................................................................................... 5 1.2 Packing List ............................................................................................................... 5 2. Hardware Configuration ........................................................................
Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Always note that improper disassembling action could cause damage to the motherboard.
ECM-CX700 Series 2. Hardware Configuration Note: For further product information, please visit our website: http://www.avalue.com.tw For further update information, please visit our technical support site: http://www.avalue.com.tw/support For further sales issue, please e-mail us: sales@avalue.com.
Quick Installation Guide 2.
ECM-CX700 Series 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
Quick Installation Guide Connectors Label Function Note JAUD1 Audio connector 6 x 2 header, pitch 2.0mm JCD1 CD-ROM audio input connector 4 x 1 wafer, pitch 2.0mm JCF1 Compact Flash card connector JCOM1 Serial port 1 connector 5 x 2 header, pitch 2.0mm JCOM2 Serial port 2 connector 5 x 2 header, pitch 2.0mm JDIMM1 DDR2 SODIMM 1.8V 200-pin DDR2 SODIMM socket JDIO1 General purpose I/O connector 5 x 2 header, pitch 2.0mm JFAN1&2 CPU fan connector 2 x 1 wafer, pitch 2.
ECM-CX700 Series 2.3 Setting Jumpers & Connectors 2.3.1 AT/ATX Power Select (JAT1, JSUS1) JAT1 AT* ATX * Default JSUS1 Signal PIN PWR_ON 1 +5V 2 VCCSB 3 Note: The default sets 2-3 closed for AT power used.
Quick Installation Guide 2.3.2 Clear CMOS (JCMOS1) Protect * Clear CMOS * Default 2.3.3 PCI-104 Voltage Select (JVIO1) +5V* +3.
ECM-CX700 Series 2.3.4 Audio connector (JAUD1) Signal PIN PIN Signal LINEOUT_R 1 2 LINEOUT _L GND 3 4 LFE-OUT LIN_R 5 6 LIN_L MIC-IN 7 8 CEN-OUT SURR-OUT-L 9 10 SURR-OUT-R SPDIF OUT 11 12 GND * Default 2.3.
Quick Installation Guide 2.3.
ECM-CX700 Series 2.3.7 2.3.
Quick Installation Guide 2.3.9 LCD Inverter Connector (JINV1) Signal PIN +12V 1 GND 2 ENBKL 3 VR 4 +5V 5 Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by VR1. Please see the VR1 section for detailed circuitry information. 2.3.9.1 Signal Description – LCD Inverter Connector (JINV1) Signal Signal Description VR Vadj = 0.75V ~ 4.25V (Recommended: 4.
ECM-CX700 Series 2.3.
Quick Installation Guide 2.3.11 LVDS Connector (JLVDS1) Signal PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 2 +3.
ECM-CX700 Series 2.3.12 2.3.
Quick Installation Guide 2.3.14 2.3.
ECM-CX700 Series 2.3.16 LCD Backlight Brightness Adjustment Connector (JVR1) Signal PIN GND 1 VR 2 +5V 3 VCC JVR1 3 JINV1 pin 4 2 1 Variation Resistor (Recommended: 4.
