ECM-KA AMD G-Series SoC Platform 3.5” Micro Module Quick Installation Guide 2nd Ed – 01 September 2013 Part No.
ECM-KA Quick Installation Guide FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
ECM-KA Quick Installation Guide If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the support you need to get the most from your Avalue’s products. In fact, most problems reported are minor and are able to be easily solved over the phone. In addition, free technical support is available from Avalue’s engineers every business day.
ECM-KA Quick Installation Guide Content 1. Getting Started ............................................................................................................ 5 1.1 Safety Precautions ......................................................................................... 5 1.2 Packing List .................................................................................................... 5 2. Hardware Configuration .............................................................................
ECM-KA Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
ECM-KA Quick Installation Guide 2.
ECM-KA Quick Installation Guide 2.
ECM-KA Quick Installation Guide 8 ECM-KA Quick Installation Guide
ECM-KA Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
ECM-KA Quick Installation Guide HDMI1 HDMI connector J422/1 COM 1 RS-422-485 mode 2 x 3 wafer, pitch 2.00 mm JAUDIO1 Audio connector 2 x 6 wafer, pitch 2.00 mm JBKL1 LCD inverter connector 5 x 1 wafer, pitch 2.00 mm COM1 Serial port 1 connector D-sub 9-pin, male JCOM2 Serial port 2 connector 2 x 5 wafer, pitch 2.00 mm DIO1 General purpose I/O connector 2 x 6 wafer, pitch 2.00 mm JFP1 Miscellaneous setting connector 2 x 5 wafer, pitch 2.
ECM-KA Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JPCMOS1) Normal* CMOS Clear * Default 2.3.
ECM-KA Quick Installation Guide 2.3.3 LCD backlight brightness adjustment (JVR1) PWM mode* DC mode * Default 2.3.
ECM-KA Quick Installation Guide 2.3.5 COM 1 pin 9 signal select (JRI1) +5V Ring* +12V * Default 2.3.
ECM-KA Quick Installation Guide 2.3.7 Battery connector (BAT1) Signal PIN GND 2 +3.3V 1 2.3.
ECM-KA Quick Installation Guide 2.3.9 System fan connector (SYS_FAN1) 2.3.10 Signal PIN GND 1 +12V 2 EC_TACH1 3 FAN_PWM1 4 COM 1 RS-422-485 mode (J422/1) Signal PIN PIN Signal 485TX.RX-/422TX- 2 1 422RX+ 485TX.
ECM-KA Quick Installation Guide 2.3.11 LCD inverter connector (JBKL1) Signal PIN +12V 1 GND 2 BKLEN 3 BRIADJ 4 +5V 5 2.3.12 Low pin count connector (JLPC1) Signal 16 ECM-KA Quick Installation Guide PIN PIN Signal LPC_AD0 1 2 +3.
ECM-KA Quick Installation Guide 2.3.13 Audio connector (JAUDIO1) Signal PIN PIN Signal FRONT-L-OUT 1 2 FRONT-R-OUT GND 3 4 GND LINE1-L-IN 5 6 LINE1-R-IN MIC1-L-IN 7 8 MIC1-R-IN LINE1-JD 9 10 FRONT-JD GND 11 12 MIC1-JD 2.3.13.
ECM-KA Quick Installation Guide 2.3.14 Serial port 2 connector (JCOM2) Signal 2.3.
ECM-KA Quick Installation Guide 2.3.16 Miscellaneous setting connector (JFP1) Signal PIN 1 PWBT 2 3 RST# 4 PWR-LED- 5 PWR-LED+ 6 HDD-LED+ 7 HDD-LED- 8 9 COPEN# 10 2.3.17 SPI connector (JSPI1) Signal PIN PIN Signal +3.
ECM-KA Quick Installation Guide 2.3.18 EC_Program (EC_SPI1) Signal PIN PIN Signal +VSPI_EC 1 2 GND EC_FSCE# 3 4 EC_FSCK EC_FMISO 5 6 EC_FMOSI EC_HOLD# 7 2.3.
ECM-KA Quick Installation Guide 2.3.20 HDD power connector (HD_PWR1) Signal PIN +5V 4 +5V 3 GND 2 GND 1 2.3.
ECM-KA Quick Installation Guide 2.3.
ECM-KA Quick Installation Guide 2.3.23 On-board box header for USB2.0 (JUSB1) Signal PIN PIN Signal +5V 1 2 +5V USB_PN_Z_1 3 4 USB_PN_Z_0 USB_PP_Z_1 5 6 USB_PP_Z_0 GND 7 8 GND GND 9 10 GND 2.3.24 On-board box header for USB2.
ECM-KA Quick Installation Guide 2.3.25 On-board box header for USB2.0 (JUSB3) Signal PIN PIN Signal +5V 1 2 +5V USB_PN_Z_4 3 4 USB_PN_Z_5 USB_PP_Z_4 5 6 USB_PP_Z_5 GND 7 8 GND GND 9 10 GND 2.3.
