ECM-PNV (for Rev. C1 – Onboard 18bit LVDS) Intel® Atom™ D525 Dual-Core 3.5” Micro Module with Intel® ICH8-M Chipset Quick Installation Guide 2nd Ed – 22 April 2014 Part No.
ECM-PNV Quick Installation Guide FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
ECM-PNV Quick Installation Guide Life Support Policy Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL OF Avalue Technology Inc. As used herein: 1.
ECM-PNV Quick Installation Guide Content 1. Getting Started ............................................................................................................ 5 1.1 Safety Precautions .......................................................................................... 5 1.1 Packing List .................................................................................................... 5 2. Hardware Configuration ...........................................................................
ECM-PNV Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
ECM-PNV Quick Installation Guide 2.
ECM-PNV Quick Installation Guide 2.
ECM-PNV Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
ECM-PNV Quick Installation Guide Connectors Label Function Note BAT Battery connector 2 x 1 wafer, pitch 1.25 mm COM1 Serial port 1 connector D-sub 9-pin, male CPU_FAN CPU fan connector 3 x 1 wafer, pitch 2.54 mm J422/485_1 Serial port 2 in RS-422/485 mode 3 x 2 header, pitch 2.0 mm JTOUCH Touch panel connector 9 x 1 header, pitch 2.0 mm JAUDIO Audio connector 6 x 2 header, pitch 2.0 mm JCOM2 Serial port 2 connector 5 x 2 header, pitch 2.
ECM-PNV Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT) Protect* Clear CMOS * Default 2.3.
ECM-PNV Quick Installation Guide 2.3.3 Touch panel mode select (JTOUCH_SEL) 4/ 8W 5W* * Default 2.3.
ECM-PNV Quick Installation Guide 2.3.5 LCD backlight brightness adjustment (JVR) * Signal PIN PIN Signal +5V 1 2 DA1 BRIGHT 3 4 BRIGHT GND 5 6 PWM1 *Default 2.3.
ECM-PNV Quick Installation Guide 2.3.6.1 Signal Description –AT/ ATX mode & Input power type Input power type Power-ON Mode Description AT Mode (PWR MSEL) Use AT type power input, and set the board in AT mode. AT Type ATX Mode (PWR MSEL) Use AT type power input, and set the board in ATX mode. AT Mode (PWR MSEL) Use ATX type power input, and set the board in AT mode. ATX Type (PWR_SB) ATX Mode (PWR MSEL) Use ATX type power input, and set the board in ATX mode.
ECM-PNV Quick Installation Guide 2.3.7 2.3.
ECM-PNV Quick Installation Guide 2.3.9 Serial port 2 in RS-422/485 mode (J422/485_1) J422/485_1 J422/485_1 Signal PIN PIN Signal TX- 1 2 RX- TX+ 3 4 RX+ +5V 5 6 GND Note: J422/485 is available after modifying the mode of COM2 in BIOS setting. And the wiring must changed to E1701150300R and Connecting it to this J422/485_1 connector.
ECM-PNV Quick Installation Guide 2.3.10 Audio connector (JAUDIO) Signal PIN PIN Signal LINEOUT_R 1 2 LINEOUT_L GND 3 4 GND LINEIN_R 5 6 LINEIN_L MIC-R 7 8 MIC-L FRONT-JD 9 10 LINE1-JD MIC1-JD 11 12 GND 2.3.
ECM-PNV Quick Installation Guide 2.3.
ECM-PNV Quick Installation Guide 2.3.13 Touch panel connector (JTOUCH) PIN 4-WIRE 5-WIRE 8-WIRE 1 N/A N/A Right Sense 2 N/A N/A Left Sense 3 N/A N/A Bottom Sense 4 N/A Sense Top Sense 5 Right LR Right Excite 6 Left LL Left Excite 7 Bottom UR Bottom Excite 8 Top UL Top Excite 9 GND GND GND PIN PIN Signal 2.3.
ECM-PNV Quick Installation Guide 2.3.
ECM-PNV Quick Installation Guide 2.3.
ECM-PNV Quick Installation Guide 2.3.17 LCD Inverter Connector (JBKL) JBKL Signal PIN +12V 1 GND 2 BLK_ON 3 BRIGHT 4 +5V 5 Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by JVR. Please see the JVR section for detailed circuitry information. 2.3.17.1 Signal Description – LCD Inverter Connector (JBKL) Signal Signal Description BRIGHT Vadj = 0.75V ~ 4.25V (Recommended: 4.
ECM-PNV Quick Installation Guide 2.3.18 Power connector (PWR) Signal PIN PIN Signal GND 2 4 VIN GND 1 3 VIN 2.3.
ECM-PNV Quick Installation Guide 2.4 Audio / USB Daughter Board User’s Guide 2.4.1 Jumper and Connector Layout 2.4.2 Jumper and Connector List Connectors Label Function Note CN1, CN2 USB connector CN4 Line out connector Phone Jack CN5 Line in connector Phone Jack CN6 Mic in connector Phone Jack JAUDIO Audio connector 6 x 2 header, pitch 2.0mm JP1 2.54mm USB connector 5 x 2 header, pitch 2.54mm JP2 2.54mm USB connector 5 x 2 header, pitch 2.54mm JP4 2.
ECM-PNV Quick Installation Guide 2.4.3 Setting Jumper and Connector Audio Connector (JAUDIO) Signal PIN PIN 2.54mm USB Connector (JP1) Signal Signal PIN PIN Signal OUTR 1 2 OUTL +5V 1 2 GND GND 3 4 GND D1- 3 4 GND INR1 5 6 INL1 D1+ 5 6 D2+ MICIN1 7 8 AREF GND 7 8 D2- FRONT-JD1 9 10 LINE1-JD1 GND 9 10 +5V MIC1-JD1 11 12 GND 2.54mm USB Connector (JP2) Signal PIN PIN Note: Wrong USB cable configuration with your USB devices might damage your USB devices.
