ECM-QM57 Intel® Core™ i7/i5/Celeron 3.5” Micro Module with Intel® QM57 Chipset Quick Installation Guide 1st Ed – 30 August 2010 Part No.
ECM-QM57 Quick Installation Guide FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
ECM-QM57 Quick Installation Guide detailed than the ones we can give over the phone. So please consult the user’s manual first. To receive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.com.tw/ If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the support you need to get the most from your Avalue’s products.
ECM-QM57 Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
ECM-QM57 Quick Installation Guide 2.
ECM-QM57 Quick Installation Guide 2.
ECM-QM57 Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
ECM-QM57 Quick Installation Guide Connectors Label Function Note BBAT1 Battery connector 2 x 1 wafer, pitch 1.25 mm BLED1 CFAST LED connector 1 2 x 1 header, pitch 2.0 mm BLED2 CFAST LED connector 2 2 x 1 header, pitch 2.0 mm COM1 Serial port 1 connector D-sub 9-pin, male CPU_FAN1 CPU fan connector 3 x 1 wafer, pitch 2.54 mm FPC_PCIE1 PCIE slot HDMI1 HDMI connector J422/485 Serial port 1 in RS-422/485 mode 3 x 2 header, pitch 2.0 mm JAUDIO1 Audio connector 7 x 2 header, pitch 2.
ECM-QM57 Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* Clear CMOS * Default 2.3.
ECM-QM57 Quick Installation Guide 2.3.3 AT/ ATX Input power select (PWR_MSEL1) AT* ATX * Default 2.3.
ECM-QM57 Quick Installation Guide 2.3.4.1 Signal Description –AT/ATX mode & Input power type Input power type Power-ON Mode Description AT Mode (PWR_MSEL1) Use AT type power input, and set the board in AT mode. AT Type ATX Mode (PWR_MSEL1) Use AT type power input, and set the board in ATX mode. AT Mode (PWR_MSEL1) Use ATX type power input, and set the board in AT mode. ATX Type (PWR_SB) ATX Mode (PWR_MSEL1) Use ATX type power input, and set the board in ATX mode.
ECM-QM57 Quick Installation Guide 2.3.5 2.3.
ECM-QM57 Quick Installation Guide 2.3.7 CPU fan connector (CPU_FAN1/ SYS_FAN1) CPU_FAN1 SYS_FAN1 2.3.
ECM-QM57 Quick Installation Guide 2.3.9 Audio connector (JAUDIO1) Signal PIN PIN Signal GND 12 11 MIC1_JD LIN1_JD 10 9 FRONT_JD MIC1_L 8 7 MIC1_R LIN1_L 6 5 LIN1_R GND 4 3 GND FRONT_L 2 1 FRONT_R 2.3.
ECM-QM57 Quick Installation Guide 2.3.11 LCD backlight brightness adjustment (JVR1) Signal PIN +5V 1 BRIGHT 2 GND 3 Variation Resistor (Recommended: 4.7KΩ, >1/16W) 2.3.12 Low pin count connector (JLPC1) Signal PIN PIN Signal GND 14 13 +5V GND 12 11 +5V GND 10 9 INT_SERIRQ CLK_LPC 8 7 LPC_AD3 LPC_FRAME# 6 5 LPC_AD2 PLT_RST# 4 3 LPC_AD1 +3.
ECM-QM57 Quick Installation Guide 2.3.13 LCD Inverter Connector (JBKL2) Signal PIN +12V 1 GND 2 BLEN 3 L_BKLT_CTRL_R 4 +5V 5 Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by JVR1. Please see the JVR1 section for detailed circuitry information. 2.3.13.1 Signal Description – LCD Inverter Connector (JBKL2) Signal Signal Description L_BKLT_CTRL_R Vadj = 0.75V ~ 4.25V (Recommended: 4.
ECM-QM57 Quick Installation Guide 2.3.14 LED backlight adjustment connector (JBKL3/ JBKL4) Signal PIN GPIO7/ DGPU_HPD_INTR# 1 GND 2 JBKL3 JBKL4 2.3.
ECM-QM57 Quick Installation Guide 2.3.
ECM-QM57 Quick Installation Guide 2.3.17 Miscellaneous setting connector (JFP) Signal PIN 1 PEBT 2 3 RST# 4 5 PWR-LED 6 7 HDD-LED 8 9 COPEN# 10 2.3.18 SPI connector (JSPI1) Signal PIN PIN Signal +3.
ECM-QM57 Quick Installation Guide 2.3.19 LVDS connector (JLVDS1) Signal 20 ECM-QM57 Quick Installation Guide PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 +3.
ECM-QM57 Quick Installation Guide 2.3.20 USB connector 8 & 9/ 10 & 11 (JUSB45/ JUSB67) Signal JUSB45 PIN PIN Signal +5V 1 2 GND N8/ N10 3 4 GND P8/ P10 5 6 P9/ P11 GND 7 8 N9 N11 GND 9 10 +5V JUSB67 2.3.
ECM-QM57 Quick Installation Guide 2.4 Audio / USB Daughter Board User’s Guide 2.4.1 Jumper and Connector Layout 2.4.2 Jumper and Connector List Connectors Label Function CN1, CN2 USB connector CN4 Line out connector Phone Jack CN5 Line in connector Phone Jack CN6 Mic in connector Phone Jack JAUDIO Audio connector 6 x 2 header, pitch 2.0mm JP1 2.54mm USB connector 5 x 2 header, pitch 2.54mm JP2 2.54mm USB connector 5 x 2 header, pitch 2.54mm JP4 2.
ECM-QM57 Quick Installation Guide 2.4.3 Setting Jumper and Connector Audio Connector (JAUDIO) Signal PIN PIN 2.54mm USB Connector (JP1) Signal Signal PIN PIN Signal OUTR 1 2 OUTL +5V 1 2 GND GND 3 4 GND D1- 3 4 GND INR1 5 6 INL1 D1+ 5 6 D2+ MICIN1 7 8 AREF GND 7 8 D2- FRONT-JD1 9 10 LINE1-JD1 GND 9 10 +5V MIC1-JD1 11 12 GND 2.
ECM-QM57 Quick Installation Guide 24 ECM-QM57 Quick Installation Guide
