EEV-EX14 EEV-EX14 COM Express Type 6 Evaluation Carrier Board Quick Installation Guide 1st Ed – 13 March 2012 Part No.
EEV-EX14 Contents 1. Getting Started ............................................................................................... 4 1.1 1.2 Safety Precautions ................................................................................................ 4 Packing List ........................................................................................................... 4 Hardware Configuration ................................................................................ 5 2.1 2.2 2.
Quick Installation Guide 2.3.28 7.1ch Audio connector (JAUDIO1) .......................................................................................... 25 2.3.29 Front Audio connector (JAUDIO2) .......................................................................................... 25 2.4 EEV-EX14 Expansion Boards ............................................................................. 26 2.4.1 Product Overview .................................................................................
EEV-EX14 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges.
Quick Installation Guide 2.
EEV-EX14 2.
Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
EEV-EX14 Connectors Label Function AUDIO1 Audio connector ATX1 ATX1 Power connector 12 x 2 wafer, pitch 4.2mm ATX2 ATX2 Power connector 2 x 2 wafer, pitch 4.2mm COM1 Serial port 1 connector D-Sub 9 pin CFAN1 CPU fan connector 1 4 x 1 wafer CFAN2 CPU fan connector 2 4 x 1 wafer DP1 Display port connector EXPRESS1 Express card connector FDC1 Floppy connector 1 HDMI1 HDMI connector 1 JAUDIO1 7.1ch Audio connector 6 x 2 header, pitch 2.
JVR1 LCD backlight brightness adjustment Quick Installation Guide 3 x 1 header, pitch 2.54mm connector PCIE1 PCI Express x16 connector PCIEXPRESS_164V PCIE2 Digital Display Interfaces (DDI) slot PCIEXPRESS_164V PCIE3 PCI Express x4 connector PCIEXPRESS_64V PCIE4 PCI Express x1 connector PCIEXPRESS_36V JCD1 CD-ROM Audio Input connector 4 x 1 wafer, pitch 2.54mm SATA 1/2/3/4 Serial ATA connector JAUDIO2 Front Audio connector 5 x 2 wafer, pitch 2.
EEV-EX14 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* Clear CMOS * Default 2.3.
Quick Installation Guide 2.3.3 PCIE signal selector (JPCIE1) Default* Signal PIN GND 1 SEL 2 +3.3V 3 PCI Express Differential Transmit Pairs JPCIE1 PCIE [0] SEL=LOW PCIE3 SEL=HIGH LAN2 2.3.4 PCIE [1] PCIE [2] PCIE [3] PCIE LAN2 PCIE4 MIIN-PCIE1 EXPRESS1 X [4] PCIE [5] PCIE [6] PCIE [7] PCIE4 MIIN-PCIE1 EXPRESS1 X X X PCIE2 (DDI) signal selector (JHDMI1) HDMI/SDVO* Display Port Signal PIN +3.
EEV-EX14 2.3.5 COM1 Pin 9 signal select (JRI1) Ring* +5V +12V *Default 2.3.
Quick Installation Guide 2.3.7 ATX1 Power connector (ATX1) Signal 2.3.
EEV-EX14 2.3.
Quick Installation Guide 2.3.
EEV-EX14 2.3.11 2.3.
Quick Installation Guide 2.3.13 Serial Port 2 RS422/485 connector (J422/485) 422 Mode Signal PIN PIN Signal TX- 1 2 RX- TX+ 3 4 RX+ +5V 5 6 GND 485 Mode 2.3.
EEV-EX14 2.3.15 General Purpose I/O connector (JDIO1) 2.3.
Quick Installation Guide 2.3.17 Pin Signal 2.3.
EEV-EX14 2.3.19 Carrier board SPI FLASH programming (JSPI2) 2.3.20 Signal PIN PIN Signal +3VSB 1 2 GND SPI_CS# 3 4 SPI_CLK SPI_MOSI 5 6 SPI_MISO SPI_HOLD# 7 LCD backlight brightness adjustment connector (JVR1) Signal PIN +5V 1 LVDS_BKLT_CTRL 2 GND 3 Variation Resistor (Recommended: 4.
Quick Installation Guide 2.3.21 LCD Inverter connector (JBKL1) Signal PIN +12V_BKL 1 GND 2 BKLEN 3 LVDS_BKLT_CTRL/PWM 4 +5V 5 Note: For inverter with brightness control function through LVDS_BKLT_CTRL/PWM signal (Pin-4) , it is possible to control the brightness level by carrier board's JVR1 pin2. In this case, R179 would be removed to disconnect the PWM control signal from COMExpress module (CN1A Pin-B84). 2.3.21.
EEV-EX14 2.3.22 LVDS connector (LVDS1) 2.3.23 Signal PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 +3.
Quick Installation Guide 2.3.24 2.3.25 LPC port connector (JLPC1) Signal PIN PIN Signal AD0 1 2 +3.
EEV-EX14 2.3.26 2.3.27 SPDIF connector (JSPDIF1) Signal PIN +3.
Quick Installation Guide 2.3.28 7.1ch Audio connector (JAUDIO1) Signal Note： PIN PIN Signal LFE-OUT 1 2 CEN-OUT GND 3 4 GND SURR-R-OUT 5 6 SURR-L-OUT SIDESURR-R-OUT 7 8 SIDESURR-L-OUT CEN-JD 9 10 SURR-JD SIDESURR-JD 11 12 GND Pin to pin to the Audio Expansion Card KJAUDIO2 connector 2.3.
EEV-EX14 2.4 EEV-EX14 Expansion Boards 2.4.
Quick Installation Guide AUDIO Expansion Card(7.1channel & Front audio) 2.4.
EEV-EX14 2.5 EEV-EX14 Expansion Boards Setting 2.5.1 Audio Expansion Card for Front Audio (KJAUDIO1) Signal AUDIO Expansion Card (7.1channel & Front audio) 2.5.2 PIN PIN Signal MIC2-L-IN 1 2 GND MIC2-R-IN 3 4 ACZ_DET# LINE2-R-OUT 5 6 MIC2_JD GND 7 LINE2-L-OUT 9 10 LINE2-JD Audio Expansion Card for 7.1ch Audio (KJAUDIO2) Signal AUDIO Expansion Card (7.
