EEV-Q702 Qseven Carrier Board Quick Installation Guide 1st Ed – 26 March 2014 Part No.
EEV-Q702 FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
Quick Installation Guide these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. Avalue Technology Inc. makes no representation or warranty that such application will be suitable for the specified use without further testing or modification.
EEV-Q702 Contents 1. Getting Started ........................................................................................................... 5 1.1 Safety Precautions ................................................................................................ 5 1.2 Packing List ........................................................................................................... 5 2. Hardware Configuration .......................................................................................
Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EEV-Q702 2.
Quick Installation Guide 2.
EEV-Q702 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
Quick Installation Guide Connectors Label Function Note SD SD card slot JCPUFAN CPU fan connector 4 x 1 wafer, pitch 2.54mm HD_PWR1/2 HD Power connector 1/2 4 x 1 wafer, pitch 2.50mm BAT-1 Battery connector JFP Miscellaneous setting connector 5 x 2 wafer, pitch 2.00mm JBKLT LCD inverter connector 5 x 1 wafer, pitch 2.00mm EDP eDP connector DIN 44-pin wafer, pitch 0.50mm COM1 Serial Port 1 connector D Sub 9 pin male JDIO General purpose I/O connector 10 x 2 header, pitch 2.
EEV-Q702 2.3 Setting Jumpers & Connectors 2.3.1 PCIE signal selector (JPCIESEL) PCIE 1* PCIE 2 *Default 2.3.
Quick Installation Guide 2.3.3 USB power selector (JUSB_PW) Standby power to USB* USB power when main power ok *Default 2.3.4 USB Port selector (JUSBSEL) Port 6, 7 to JUSB1 (USB3.0)* Port 6, 7 to JUSB3 (USB2.
EEV-Q702 2.3.5 AT/ ATX Input power select (JAT_ATX) AT MODE* ATX MODE *Default 2.3.
Quick Installation Guide 2.3.7 eDP/ LVDS selector (JEDPLVDS) HI, LVDS port OUTPUT* LOW, eDP port OUTPUT *Default 2.3.8 JDPQVER selector (JQ7_VER) Q7 2.0* Q7 1.
EEV-Q702 2.3.9 2.3.
Quick Installation Guide 2.3.11 2.3.
EEV-Q702 2.3.13 2.3.14 ATX1 Power connector (PWR1) Signal PIN PIN +3.3V 12 24 GND +12V 11 23 +5V +12V 10 22 +5V +5V 9 21 +5V ATX_POK 8 20 NC GND 7 19 GND +5V 6 18 GND GND 5 17 GND +5V 4 16 PS_ON# GND 3 15 GND +3.3V 2 14 NC +3.3V 1 13 +3.3V ATX2 Power connector (PWR2) Signal .
Quick Installation Guide 2.3.15 Carrier board SPI FLASH programming (JSPIC) Signal 2.3.16 PIN PIN Signal +3.3V 1 2 GND SPI_CS# 3 4 SPI_CLK SPI_SO 5 6 SPI_SI SPI_WP#_PRG 7 8 NC LPC port Connector (JLPC) Signal PIN PIN Signal LPC_AD0 1 2 +3.
EEV-Q702 2.3.17 LCD Inverter connector (JBKLT) Signal +5V (max 400mA) 4 +5V 3 GND 2 (max 300mA) 2.3.17.1 Signal Description – LCD Inverter connector (JBKLT) Signal Description LVDS_BKLTCTL LVDS backlight PWM control LVDS_BPEN LCD backlight Enable/Disable control signal LVDS_EN level selectable resistor - 5V or 3.3V (Default 5V level) 18 EEV-Q702 Quick Installation Guide 5 +3.
Quick Installation Guide 2.3.18 General Purpose I/O connector (JDIO) Signal Signal DI0 1 2 DO0 DI1 3 4 DO1 DI2 5 6 DO2 DI3 7 8 DO3 DI4 9 10 DO4 DI5 11 12 DO5 DI6 13 14 DO6 DI7 15 16 DO7 SMB_CLK 17 18 SMB_DATA GND 2.3.
EEV-Q702 2.3.
