EMS-BYT Series Fanless Intel® Celeron®/Atom™ SoC Rugged Embedded System Quick Reference Guide 1st Ed –21 May 2014 Copyright Notice Copyright 2014 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No.
EMS-BYT Series FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
Quick Reference Guide Content 1. Getting Started ............................................................................................................ 5 1.1 1.2 1.3 1.4 2. Safety Precautions ................................................................................................ 5 Packing List ........................................................................................................... 5 System Specifications ..................................................................
EMS-BYT Series 2.4.9 LCD inverter connector (JBKL1) ................................................................................................ 28 2.4.10 SPI connector (SPI1) ............................................................................................................. 28 2.4.11 Front Panel Connector 1 (CN1) ............................................................................................. 29 2.4.12 Front Panel Connector 2 (CN2) .........................................
Quick Reference Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EMS-BYT Series 1.
Quick Reference Guide 1 x VGA, 1 x HDMI (EMS-BYT-HDMI) 1 x VGA, 1 x DVI (EMS-BYT-DVI) Audio Port Mic-in, Line-in, Line-out GPIO 6-bit GPI and 6-bit GPO 3 x USB 2.0 (Rear 2; Front 1) (EMS-BYT) 5 x USB 2.
EMS-BYT Series 1hr/axis Protection Shock Protection With mSATA/SSD: 50G, IEC 60068-2-27, Half Sine, 11ms CE, FCC Class B (EMS-BYT, EMS-BYT-6COM, EMS-BYT-5LAN, Certification Dimension (W x H x EMS-BYT-4COM Isolation, EMS-BYT-HDMI, EMS-BYT-DVI) CE, FCC Class A (EMS-BYT-PoE) 240mm x 170mm x 45mm (EMS-BYT) 240mm x 170mm x 60mm (EMS-BYT-6COM, EMS-BYT-5LAN, D) EMS-BYT-4COM Isolation, EMS-BYT-PoE, EMS-BYT-HDMI, EMS-BYT-DVI) Weight 8 4.
Quick Reference Guide 1.4 System Overview 1.4.
EMS-BYT Series 1.4.2 Front View 1.4.
Quick Reference Guide EMS-BYT-5LAN/PoE EMS-BYT-HDMI EMS-BYT-DVI EMS-BYT Series Quick Reference Guide 11
EMS-BYT Series EMS-BYT Connectors Label Function COM1 Serial port connector 1 DC-IN DC power-in connector LAN1 RJ-45 Ethernet 1 Multi-function port Note Multi-Function Port combined COM2, 2 PS/2, Audio, GPIO and SMBus USB1~3 USB connector 1~3 VGA VGA connector Swappable Drawer 2.
Quick Reference Guide Swappable Drawer 2.5” Driver Bay and SIM Card HDD HDD indicator EMS-BYT-HDMI Connectors Label Function COM1 Serial port connector 1 COM3~4 Serial port connector 3~4 DC-IN DC power-in connector LAN1~3 RJ-45 Ethernet 1~3 Multi-function port Note Multi-Function Port combined COM2, 2 PS/2, Audio, GPIO and SMBus USB1~5 USB connector 1~5 VGA VGA connector Swappable Drawer 2.
EMS-BYT Series 2. Hardware Configuration Jumper and Connector Setting, Driver and BIOS Installing For advanced information, please refer to: 1- EBM-BYTS, AUX-M01, AUX-M02, AUX-M04, AUX-M07, EBM-BYTS DB-A and EBM-CDVS DB-A included in this manual. Note: If you need more information, please visit our website: http://www.avalue.com.
Quick Reference Guide 2.1 EMS-BYT connector mapping 2.1.1 2.1.
EMS-BYT Series 2.1.3 VGA connector (VGA) PIN Signal PIN Signal PIN Signal 1 RED 6 GND 11 NC 2 GREEN 7 GND 12 DDCDAT 3 BLUE 8 GND 13 HSYNC 4 NC 9 +5V 14 VSYNS 5 GND 10 GND 15 DDCCLK 2.1.
Quick Reference Guide 2.1.4.1 GPIO+SMBUS Signal PIN PIN 25 13 24 12 23 11 22 10 SMBUS_DATA 21 9 SMBUS_CLK 20 8 GPI-D5 19 7 GPI-D4 18 6 GPI-D3 17 5 GPI-D2 16 4 GPI-D1 15 3 GPI-D0 14 2 1 Signal GND 5V GPO-D5 GPO-D4 GPO-D3 GPO-D2 GPO-D1 GPO-D0 2.1.4.
EMS-BYT Series 2.2 EBM-BYTS, AUX-M01, AUX-M02, AUX-M04, AUX-M07, EBM-BYTS DB-A and EBM-CDVS DB-A Overviews 2.2.
Quick Reference Guide 2.2.2 AUX-M01 2.2.
EMS-BYT Series 2.2.4 AUX-M04 2.2.
Quick Reference Guide 2.2.6 EBM-BYTS DB-A 2.2.
EMS-BYT Series 2.3 EBM-BYTS Jumper & Connector list Jumpers Label Function Note JCMOS1 Clear CMOS 3 x 1 header, pitch 2.54mm JCMOS2 Clear CMOS (Reserved) 3 x 1 header, pitch 2.54 mm JRI1/2 COM 1/2 pin 9 signal select 3 x 2 header, pitch 2.00 mm JAT1 AT/ ATX Input power select 3 x 1 header, pitch 2.00 mm SW1 Serial port 1/ 2 – RS485 mode select DIP switch 6pin JUIM1 UIM Switch select JVR1 LCD backlight brightness adjustment 3 x 1 header, pitch 2.
Quick Reference Guide SO_DIMM1 DDR3 SODIMM connector MIOE_CB1 IET Expansion slot JLPC1 LPC port connector 7 x 2 header, pitch 2.00 mm SPI1 SPI connector 4 x 2 header, pitch 2.00 mm JBKL1 LCD inverter connector 5 x 1 wafer, pitch 2.00 mm SATA1 Serial ATA connector 1 CN1 Front Panel connector 1 5 x 1 wafer, pitch 2.00 mm CN2 Front Panel connector 2 8 x 1 wafer, pitch 2.00 mm DCOUT_S1 DC Output connector 6 x 1 wafer, pitch 2.00 mm JEC_ROM1 EC Debug connector 5 x 2 header, pitch 2.
EMS-BYT Series 2.4 EBM-CDVS Jumpers & Connectors settings 2.4.1 Clear CMOS (JCMOS1) Protect* Clear CMOS *Default 2.4.
Quick Reference Guide 2.4.3 AT/ ATX Input power select (JAT1) AT* ATX *Default 2.4.
EMS-BYT Series 2.4.5 IET interface DP mode select (JDDI1) Display Port* HDMI/DVI *Default 2.4.
Quick Reference Guide 2.4.7 Serial port 1/ 2 – RS485 mode select (SW1) In Serial Port 1 mode 1 2 3 ON OFF Auto Direction RTS# Control* 485TXP external OPEN* biasing resistor 485TXN external OPEN* biasing resistor In Serial Port 2 mode 4 5 6 2.4.8 ON OFF Auto Direction RTS# Control* 485TXP external OPEN* biasing resistor 485TXN external OPEN* biasing resistor LPC port connector (JLPC1) Signal PIN PIN Signal LPC_AD0 1 2 +3.
EMS-BYT Series 2.4.9 2.4.
Quick Reference Guide 2.4.11 2.4.12 Front Panel Connector 1 (CN1) Signal PIN PWR_BTN_IN# 1 SYSRST# 2 GND 3 +5VSB 4 PWR_LED- 5 Front Panel Connector 2 (CN2) Signal PIN +3.3V 1 SATA_5V_LED# 2 +3.3VSB 3 LAN1_LED_ACT_n 4 +3.3VSB 5 LAN1_LED_100#_n 6 +3.
EMS-BYT Series 2.4.13 2.4.
Quick Reference Guide 2.4.15 2.4.16 On-board header for USB2.0 (JUSB1) Signal PIN USBVCC_HEADER 1 USB_HUB2_DN_1 2 USB_HUB2_DP_1 3 GND 4 GND 5 LVDS connector (JLVDS1) Signal PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 +3.
EMS-BYT Series 2.5 AUX-M01, AUX-M02, AUX-M04, AUX-M07, EBM-BYTS DB-A and EBM-CDVS DB-A Jumper & Connector list 2.5.1 AUX-M01 Jumpers Label Function Note JRI3/4/5/6 COM 3/4/5/6 pin 9 signal select 3 x 2 header, pitch 2.00mm Label Function Note USB1~2 USB connector 1~2 USB3 USB connector 3 5 x 1 wafer, pitch 2.00mm JUSB3 USB connector 3 5 x 1 header, pitch 2.00mm COM3~6 Serial port connector 3~6 PJP1 SMBUS of TCA9555 address setting Connectors 2.5.2 3 x 2 header, pitch 2.
Quick Reference Guide 2.5.4 AUX-M07 Connectors Label Function USB1~2 USB connector 1~2 COM3~6 Serial port connector 3~6 SJP2 SMBUS of TCA9555 address setting 2.5.5 Note 3 x 2 header, pitch 2.00mm EBM-BYTS DB-A Jumpers Label Function Note OJRI3/4 COM 3/4 pin 9 signal select 3 x 2 header, pitch 2.00mm Label Function Note OUSB1~2 USB connector 1~2 LAN2~3 LAN connector 2~3 COM3~4 Serial port connector 3~4 HDMI1 HDMI connector 3 x 2 header, pitch 2.
EMS-BYT Series 2.6 AUX-M01 Jumpers & Connectors settings 2.6.1 COM 3/4/5/6 pin 9 signal select (JRI3/4/5/6) +5V JRI6 Ring* JRI5 +12V JRI4 JRI3 * Default 2.6.
Quick Reference Guide 2.6.3 2.6.
EMS-BYT Series 2.7 AUX-M02 Connectors settings 2.7.1 LAN ACT/LNK/SPD LED (JLANLED) Signal 2.7.2 Signal Z_LAN_LED_1000#_3 15 16 Z_LAN_LED_1000#_1 Z_LAN_LED_100#_3 13 14 Z_LAN_LED_100#_1 Z_LAN_LED_ACT_3 11 12 Z_LAN_LED_ACT_1 +3.3VSB 9 10 +3.3VSB Z_LAN_LED_1000#_4 7 8 Z_LAN_LED_1000#_2 Z_LAN_LED_100#_4 5 6 Z_LAN_LED_100#_2 Z_LAN_LED_ACT_4 3 4 Z_LAN_LED_ACT_2 +3.3VSB 1 2 +3.
Quick Reference Guide 2.8 AUX-M04 Jumpers & Connectors settings 2.8.1 Operating Modes select (ZJP1) Normal Auto* Reset * Default 2.8.
EMS-BYT Series 2.8.3 LAN ACT/LNK/SPD LED (Z_JLANLED) Signal 38 PIN PIN Signal Z_LAN_LED_1000#_3 15 16 Z_LAN_LED_1000#_1 Z_LAN_LED_100#_3 13 14 Z_LAN_LED_100#_1 Z_LAN_LED_ACT_3 11 12 Z_LAN_LED_ACT_1 +3.3VSB 9 10 +3.3VSB Z_LAN_LED_1000#_4 7 8 Z_LAN_LED_1000#_2 Z_LAN_LED_100#_4 5 6 Z_LAN_LED_100#_2 Z_LAN_LED_ACT_4 3 4 Z_LAN_LED_ACT_2 +3.3VSB 1 2 +3.
Quick Reference Guide 2.9 AUX-M07 Connector settings 2.9.
EMS-BYT Series 2.10 EBM-BYTS DB-A Jumpers & Connectors settings 2.10.1 COM 3/4 pin 9 signal select (OJRI3/4) +5V Ring* OJRI4 +12V OJRI3 * Default 2.10.
Quick Reference Guide 2.10.
EMS-BYT Series 2.11 EBM-CDVS DB-A Connector settings 2.11.
Quick Reference Guide 2.12 Installing Hard Disk & Memory, PCI devices (EMS-BYT Series) Step 1. Remove 6 screws from the bottom of your system. Step 2. Remove the chassis cover. Step 1. Remove 5 screws to release the HDD bracket. Step 2.1 Slide HDD into its bracket until properly seated. Step 2.2 Secure HDD by means of 5 screws. Step 3. Slide the DDR3 SODIMM into the memory socket and press it down until properly seated. Step 4.
EMS-BYT Series 2.13 Installing Mounting Brackets (EMS-BYT Series) Step 1. Position brackets on both sides, matching the holes on the system. Step 2. Insert and fasten screw on each side of the system to secure Mounting brackets.
