EMX-CDD Intel® Atom™ D2550 Process + NM10 Chipset Mini ITX Motherboard User’s Manual 1st Ed – 30 September 2013 Part No.
EMX-CDD User’s Manual FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
EMX-CDD User’s Manual Content 1. Getting Started ............................................................................................................ 6 1.1 Safety Precautions .......................................................................................... 6 1.2 Packing List .................................................................................................... 6 1.3 Document Amendment History....................................................................... 7 1.
EMX-CDD User’s Manual 2.4.25 CPU Fan connector (CFAN1) ................................................................ 29 3.BIOS Setup .................................................................................................................... 30 3.1 Introduction................................................................................................... 31 3.2 Starting Setup............................................................................................... 31 3.3 Using Setup ....
EMX-CDD User’s Manual 4. Drivers Installation....................................................................................................... 56 4.1 Install Chipset Driver .................................................................................... 57 4.2 4.3 4.4 Install VGA Driver ......................................................................................... 59 Install LAN Driver (For Realtek 8111E Gigabit Ethernet) .............................
EMX-CDD User’s Manual 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EMX-CDD User’s Manual 1.
EMX-CDD User’s Manual 1.4 Manual Objectives This manual describes in details Avalue Technology EMX-CDD Single Board. We have tried to include as much information as possible but we have not duplicated information that is provided in the standard IBM Technical References, unless it proved to be necessary to aid in the understanding of this board. We strongly recommend that you study this manual carefully before attempting to set up EMX-CDD series or change the standard configurations.
EMX-CDD User’s Manual 1.5 Specifications System CPU Intel® Atom™ processor D2550 Processor BIOS AMI uEFI BIOS, 16Mbit SPI Flash ROM System Chipset Intel® NM10 I/O Chip Winbond W83627UHG System Memory 1 x 204-pin DDR3 1066/1333 MHz SODIMMs, up to 4GB H/W Reset, 1sec. – 65535sec./min 1sec. or 1min.
EMX-CDD User’s Manual 1 x 5 pin, pitch 2.54mm connector for Inverter 1 x 2 x 5 pin, pitch 2.54mm connector for Audio 1 x 3 pin, pitch 2.54mm connector for LVDS PWR selection 1 x 2 x 12 pin, pitch 2.54mm connector for printer port 1 x 2 x 5 pin, pitch 2.54mm connector for VGA 1 x 2 x 5 pin, pitch 2.54mm connector for Keyboard & Mouse 1 x 1 x 4 pin, pitch 2.
EMX-CDD User’s Manual 1.6 Architecture Overview—Block Diagram The following block diagram shows the architecture and main components of EMX-CDD.
EMX-CDD User’s Manual 2.
EMX-CDD User’s Manual 2.
EMX-CDD User’s Manual 2.2 Installation Procedure This chapter explains you the instructions of how to setup your system. 1. Turn off the power supply. 2. Insert the DIMM module (be careful with the orientation). 3. Insert all external cables for hard disk, floppy, keyboard, mouse, USB etc. except for flat panel. A CRT monitor must be connected in order to change BIOS settings to support flat panel. 4. Connect power supply to the board via the AC/DC Adapter. 5. Turn on the power. 6.
EMX-CDD User’s Manual 2.3 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
EMX-CDD User’s Manual Connectors Label Function Note FPANEL1 Front Panel Switches 2 x 8 header, pitch 2.54 mm MPCIE_WIFI_SATA PCIE signal selector HDMI1 HDMI connector J1 ATX power connector for DC 12V input JSPK Speaker connector 1 x 4 wafer, pitch 2.00 mm J14 DC power-in connector 2 x 2 header, pitch 4.20 mm JCOM1~6 Serial port 1~6 connector 2 x 5 header, pitch 2.00 mm GPIO General Purpose I/O 2 x 6 header, pitch 2.54 mm JLVDS1 LVDS connector 2 x 20 wafer, pitch 1.
EMX-CDD User’s Manual 2.4 Setting Jumpers & Connectors 2.4.1 Clear CMOS (JBAT1) Normal* Clear CMOS * Default 2.4.
EMX-CDD User’s Manual 2.4.3 Jumper for COM2, IR selection (JIR1~2) IR* COM JIR2 JIR1 * Default Pin Define 1-2 COM 2-3 IR Note: IR is not functional. 2.4.
EMX-CDD User’s Manual 2.4.5 Jumper for MPCIE_WIFI_SATA (JP1~4) SATA2* MINIPCIE JP4 JP3 JP2 JP1 M-SATA PIN Define * Default 1-2 MINIPCIE Note: SATA 2 bond together with M-SATA, it can only 2-3 M-SATA work either way at one time. 3-4 SATA2 2.4.6 Jumper for LVDS power (LVDS_PWR1) 5V* 3.3V * Default Pin Define Max current 1-2 5V 1A 2-3 3.
EMX-CDD User’s Manual 2.4.7 Jumper for inverter power (ADJ_PWR1) 5V* 0 5V * Default 2.4.
EMX-CDD User’s Manual 2.4.9 Jumper for Serial port 1~6 selection (JC1~6) +5V JC6 JC5 JC4 JC3 JC2 JC1 2.4.
EMX-CDD User’s Manual 2.4.11 General Purpose I/O (GPIO) Signal 2.4.
EMX-CDD User’s Manual 2.4.13 LVDS connector (JLVDS1) Signal Note: Mapping connector DF13-40DS-1.25C (1.0mm).
EMX-CDD User’s Manual 2.4.14 Printer (JLPT) Signal 2.4.15 PIN PIN Signal 25 SLCT GND 24 23 PE GND 22 21 BUSY GND 20 19 ACK GND 18 17 PD7 GND 16 15 PD6 GND 14 13 PD5 GND 12 11 PD4 GND 10 9 PD3 SLIN 8 7 PD2 INIT 6 5 PD1 ERR 4 3 PD0 AFD 2 1 STB VGA connector (JVGA) Signal Note: It can only use either D-SUB connector or Pin Header.
EMX-CDD User’s Manual 2.4.16 2.4.17 Inverter connector (JINVERT1) PIN Signal Max current 1 12V 1A 2 GND 3 BLEN 4 PWM 5 5V 1A USB Connector 1~3 - USB2.
EMX-CDD User’s Manual 2.4.18 2.4.
EMX-CDD User’s Manual 2.4.20 2.4.
EMX-CDD User’s Manual 2.4.22 SATA Power connector 1~2 (SATA1~2_PWR) SATA1_PWR SATA2_PWR P P 2.4.23 PIN Signal Max current 4 5V 1A 3 GND 2 GND 1 12V 1A Speaker Headers (JSPK) PIN Signal 4 INTSPR- 3 INTSPR+ 2 INTSPL- 1 INTSPL+ Note: Support 3W X 2 speaker.
EMX-CDD User’s Manual 2.4.24 2.4.
EMX-CDD User’s Manual 3.
EMX-CDD User’s Manual 3.1 Introduction The BIOS setup program allows users to modify the basic system configuration. In this following chapter will describe how to access the BIOS setup program and the configuration options that may be changed. 3.2 Starting Setup The BIOS is immediately activated when you first power on the computer. The BIOS reads the system information contained in the NVRAM and begins the process of checking out the system and configuring it.
EMX-CDD User’s Manual 3.3 Using Setup In general, you use the arrow keys to highlight items, press to select, use the PageUp and PageDown keys to change entries, press for help and press to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard.
EMX-CDD User’s Manual 3.4 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press or the F1 key again. 3.5 In Case of Problems If, after making and saving system changes with Setup, you discover that your computer no longer is able to boot, the BIOS supports an override to the NVRAM settings which resets your system to its defaults.
EMX-CDD User’s Manual 3.6 BIOS setup Once you enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and exit choices. Use the arrow keys to select among the items and press to accept and enter the sub-menu. 3.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock. 3.6.1.1 System Language Use this option to select system language 3.6.1.
EMX-CDD User’s Manual 3.6.2 Advanced BIOS settings This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus. Item Options Launch PXE OpROM Disable[Default] Enable Description Controls the execution of UEFI and Legacy PXE OpROM. 3.6.2.
EMX-CDD User’s Manual Item Options Enable ACPI Auto Disabled Enabled[Default] Enable or Disable BIOS ACPI Auto Configuration. Disabled Enabled[Default] Enable or Disable System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS.
EMX-CDD User’s Manual 3.6.2.3 CPU Configuration Use the CPU configuration menu to view detailed CPU specification and configure the CPU. Item Options CPU C1E Support Disabled[Default] Enabled Hyper-Threading Disabled[Default] Enabled Execute Disable Bit Disabled[Default] Enabled Limit CPUID Maximum Disabled[Default] Enabled Description Enable/Disable CPU C1E state.
EMX-CDD User’s Manual 3.6.2.4 IDE Configuration Item SATA Controller(s) Configure SATA as Options Disabled Enabled[Default] IDE[Default] AHCI 3.6.2.5 USB Configuration 38 EMX-CDD User’s Manual Description SATA Ports (0-3) Device Names if Present and Enabled. Select a configuration for SATA Controller.
EMX-CDD User’s Manual Item Options Legacy USB Support Enabled[Default] Disabled Auto EHCI Hand-off Enabled Disabled[Default] USB transfer time-out Device reset time-out 1 sec 5 sec 10 sec 20 sec[Default] 10 sec 20 sec[Default] 30 sec 40 sec Auto[Default] Manual Device power-up delay Description Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
EMX-CDD User’s Manual 3.6.2.7 W83627UHG Super IO Configuration Item Serial Port 1/2/3/4/5/6 Configuration Parallel Port Configuration 3.6.2.7.1 Description Set Parameters of Serial Port 1/2/3/4/5/6 (COMA/B/C/D/E/F). Set Parameters of Parallel Port (LPT/LPTE).
EMX-CDD User’s Manual Item Serial Port Change Settings 3.6.2.7.2 Option Disabled Enabled[Default] Auto[Default] IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Description Enable or Disable Serial Port (COM). Select an optimal setting for Super IO device.
EMX-CDD User’s Manual 3.6.2.7.3 Serial Port 3 Configuration Item Serial Port Change Settings Option Disabled Enabled[Default] Auto[Default] IO=3E8h; IRQ=7; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; IO=2F0h; IRQ=3,4,5,6,7,10,11,12; IO=2E0h; IRQ=3,4,5,6,7,10,11,12; 42 EMX-CDD User’s Manual Description Enable or Disable Serial Port (COM). Select an optimal setting for Super IO device.
EMX-CDD User’s Manual 3.6.2.7.4 Serial Port 4 Configuration Item Serial Port Change Settings Option Disabled Enabled[Default] Auto[Default] IO=2E8h; IRQ=7; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; IO=2F0h; IRQ=3,4,5,6,7,10,11,12; IO=2E0h; IRQ=3,4,5,6,7,10,11,12; Description Enable or Disable Serial Port (COM). Select an optimal setting for Super IO device.
EMX-CDD User’s Manual 3.6.2.7.5 Serial Port 5 Configuration Item Serial Port Change Settings Option Disabled Enabled[Default] Auto[Default] IO=2F0h; IRQ=7; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; IO=2F0h; IRQ=3,4,5,6,7,10,11,12; IO=2E0h; IRQ=3,4,5,6,7,10,11,12; 44 EMX-CDD User’s Manual Description Enable or Disable Serial Port (COM). Select an optimal setting for Super IO device.
EMX-CDD User’s Manual 3.6.2.7.6 Serial Port 6 Configuration Item Serial Port Change Settings Option Disabled Enabled[Default] Auto[Default] IO=2E0h; IRQ=7; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; IO=2F0h; IRQ=3,4,5,6,7,10,11,12; IO=2E0h; IRQ=3,4,5,6,7,10,11,12; Description Enable or Disable Serial Port (COM). Select an optimal setting for Super IO device.
EMX-CDD User’s Manual 3.6.2.7.7 Parallel Port Configuration Item Parallel Port Change Settings Device Mode 46 EMX-CDD User’s Manual Option Disabled Enabled[Default] Auto[Default] IO=378h; IRQ=5; IO=378h; IRQ=5,6,7,11,12; None use None use STD Printer Mode[Default] SPP Mode EPP -1.9 and SPP Mode EPP -1.7 and SPP Mode ECP Mode ECP and EPP 1.9 Mode ECP and EPP 1.7 Mode Description Enable or Disable Parallel Port (LPT/LPTE). Select an optimal setting for Super IO device. Change the Serial Port mode.
EMX-CDD User’s Manual 3.6.2.8 WatchDogTimer Settings Item Options WatchDogTimer Disabled[Default] Enabled Description WatchDogTimer Setting. 3.6.2.9 W83627UHG HW Monitor The H/W Monitor shows the operating temperature, fan speeds and system voltages.
EMX-CDD User’s Manual 3.6.3 Chipset Item Description Host Bridge Host Bridge Parameters. South Bridge South Bridge Parameters. 3.6.3.1 Host Bridge Item Intel IGD Configuration Options Config Intel IGD Settings.
EMX-CDD User’s Manual 3.6.3.1.
EMX-CDD User’s Manual Port-A:LFP Driven by Int-Display Port encoder from Port-A. eDP Port-D:LFP Driven by Int-DisplayPort encoder from Port-D(through PCH). Fixed Graphics Memory 128 MB[Default] 256 MB Size Configure Fixed Graphics Memory Size. 3.6.3.
EMX-CDD User’s Manual 3.6.3.2.
EMX-CDD User’s Manual PME SCI Hot Plug Enabled Disabled Enabled[Default] Disabled[Default] Enabled Extra Bus Reserved 0-7 Reserved Memory 1-20 Reserved I/O 4-20 3.6.4 Correctable Error Enable/Disable. PCI Express PME SCI Enable/Disable. PCI Express Hot Plug Enable/Disable. Extra Bus Reserved (0-7) for bridges behind this Root Bridge. Reserved Memory and Prefetchable Memory (1-20MB) Range for this Root Bridge. Reserved I/O (4K/8K/12K/16K/20K) Range for this Bridge.
EMX-CDD User’s Manual 3.6.5 Security Use the Security menu to set system and user password. 3.6.5.1 Administrator Password This setting specifies a password that must be entered to access the BIOS Setup Utility. If only the Administrator's password is set, then this only limits access to the BIOS setup program and is only asked for when entering the BIOS setup program. By default, no password is specified. 3.6.5.
EMX-CDD User’s Manual 3.6.6 Save & Exit 3.6.6.1 Save Changes and Exit Exit system setup after saving the changes. 3.6.6.2 Discard Changes and Exit Exit system setup without saving any changes.
EMX-CDD User’s Manual 3.6.6.3 Save Changes and Reset Reset the system after saving the changes. 3.6.6.4 Discard Changes and Reset Any changes made to BIOS settings during this session of the BIOS setup program are discarded. The setup program then exits and reboots the controller. 3.6.6.5 Save Changes Save Changes done so far to any of the setup options. 3.6.6.6 Discard Changes Discard Changes done so far to any of the setup options. 3.6.6.
EMX-CDD User’s Manual 4. Drivers Installation Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen.
EMX-CDD User’s Manual 4.1 Install Chipset Driver Insert the Supporting DVD-ROM to DVD-ROM drive, click on “start” icon and it should show the index page of Avalue’s products automatically. If not, locate the folder HTML and choose the product from the targeted folder. Note: The installation procedures and screen shots in this section are based on Windows 7 operating system. Step 1. Locate 「\Driver_Chipset\Intel\EMX-CDD_Chipset」. Step 2. Start setup. Step 3. Select Next to continue installation. Step 4.
EMX-CDD User’s Manual Step 7. Select Next to the next step. 58 EMX-CDD User’s Manual Step 8. Select Finish to complete Installation.
EMX-CDD User’s Manual 4.2 Install VGA Driver Insert the Supporting DVD-ROM to DVD-ROM drive, click on “start” icon and it should show the index page of Avalue’s products automatically. If not, locate the folder HTML and choose the product from the targeted folder. Note: The installation procedures and screen shots in this section are based on Windows 7 operating system. Step 1. Locate 「\VGA\EMX-CDD_Video」. Step 4. Select YES to continue installation. Step 2. Select Next to start setup. Step 5.
EMX-CDD User’s Manual Step 7. Select Next to the next step. 60 EMX-CDD User’s Manual Step 8. Select Finish to complete Installation.
EMX-CDD User’s Manual 4.3 Install LAN Driver (For Realtek 8111E Gigabit Ethernet) Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Gigabit\Realtek\RTL8111E\EMX-CD D_LAN. Note: The installation procedures and screen shots in this section are based on Windows 7 operation system. Step 1. Click Next to Install. Step 2.
EMX-CDD User’s Manual 4.4 Install Audio Driver (For Realtek ALC661 HD Audio) Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to \Driver_Audio\Realtek\ALC661\EMX-CDD_Audio. Note: The installation procedures and screen shots in this section are based on Windows 7 operation system.
EMX-CDD User’s Manual 5.
EMX-CDD User’s Manual Unit: mm 64 EMX-CDD User’s Manual
EMX-CDD User’s Manual Unit: mm EMX-CDD User’s Manual 65
