EMX-PNV Intel® Atom™ PNV-D525 Mini ITX Motherboard with Intel® ICH8-M Chipset Quick Installation Guide 1st Ed –27 June , 2011 Part No.
EMX-PNV Quick Installation Guide FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
EMX-PNV Quick Installation Guide easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult the user’s manual first. To receive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.com.tw/ If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer.
EMX-PNV Quick Installation Guide CONTENT 1. Getting Started ............................................................................................................ 5 1.1 Safety Precautions ......................................................................................... 5 1.2 Packing List .................................................................................................... 5 2. Hardware Configuration ............................................................................
EMX-PNV Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surge. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EMX-PNV Quick Installation Guide 2.
EMX-PNV Quick Installation Guide 2.
EMX-PNV Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
EMX-PNV Quick Installation Guide Connectors Label Function Note BT1 Battery slot connector CF1 CF card slot connector CN1 Speaker out connector 4 x 1 wafer, pitch 2.0mm CN2 USB connector 4 & 5 5 x 2 header, pitch 2.54 mm CN3 USB connector 6 & 7 5 x 2 header, pitch 2.54 mm CN4 SPI connector 3 x 2 header, pitch 2.0 mm CN5 Serial port 4 connector 5 x 2 header, pitch 2.54 mm CN6 LCD inverter connector 5 x 1 wafer, pitch 2.0mm CN7 Serial port 3 connector 5 x 2 header, pitch 2.
EMX-PNV Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* Clear CMOS * Default 2.3.2 Multi-purpose connector (JFTP1) Signal PIN PIN Signal 1 2 SB_LED+ 3 4 GND +3.
EMX-PNV Quick Installation Guide 2.3.3 Serial port 3/ 4/ 2/ 1 pin 9 signal select (JP1/ JP2/ JP3/ JP4) JP2/ 3/ 4 JP1 JP3 JP4 Ring* Ring* JP1 JP2 +5V +5V +12V * Default 2.3.
EMX-PNV Quick Installation Guide 2.3.5 Serial Port 2 Connector in RS232/422/485 (JP6) RS-232* *Default Note: COM2 is available in RS-232 mode by RS-422 RS-485 Signal PIN PIN Signal DCD#B 1 2 RXDB CM2-1 3 4 CM2-2 485TX- 5 6 422RX+ TXDB 7 8 DTR#B CM2-3 9 10 CM2-4 485TX+ 11 12 422RX- default setting. For using COM2 in 422/485 Mode, please adjust both JP5 and JP6 with corresponding Jumper settings. 2.3.
EMX-PNV Quick Installation Guide 2.3.7 2.3.
EMX-PNV Quick Installation Guide 2.3.9 SPI connector (CN4) Signal 2.3.10 PIN PIN Signal +3.
EMX-PNV Quick Installation Guide 2.3.11 LCD backlight brightness adjustment (VR1) Signal PIN +5V 1 BRIGHT 2 GND 3 Variation Resistor (Recommended: 4.7KΩ, >1/16W) 2.3.12 LCD Inverter Connector (CN6) Signal PIN +5V 5 BRIGHT 4 LBKLT_EN 3 GND 2 +12V 1 Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal controlled by VR1. Please see the VR1 section for detailed circuitry information.
EMX-PNV Quick Installation Guide 2.3.12.1 Signal Description – LCD Inverter Connector (CN6) Signal Signal Description BRIGHT Vadj = 0.75V ~ 4.25V (Recommended: 4.7KΩ, >1/16W) LBKLT_EN LCD backlight ON/OFF control signal 2.3.13 2.3.14 CD-ROM Audio Connector (CN8) Signal PIN R 4 GND 3 L 2 GND 1 Front audio connector (CN9) Signal 16 EMX-PNV Quick Installation Guide PIN PIN Signa MIC2_L 1 2 GND MIC2_R 3 4 +3.
EMX-PNV Quick Installation Guide 2.3.
EMX-PNV Quick Installation Guide 2.3.16 CPU/System fan connector (FAN1/FAN2) FAN1 (CPU_FAN) FAN2 (SYS_FAN) FAN1 FAN2 2.3.17 Signal PIN GND 1 +12V 2 FANIN 3 VGA power connector (JVGA1) 18 EMX-PNV Quick Installation Guide Signal PIN PIN Signal GND 10 9 GND +12V 8 7 +12V +12V 6 5 +12V +3.3V 4 3 +3.
EMX-PNV Quick Installation Guide 2.3.18 2.3.
EMX-PNV Quick Installation Guide 2.3.20 LVDS connector (LVDS1) Signal 20 EMX-PNV Quick Installation Guide PIN PIN Signal NC 39 40 NC GND 37 38 GND NC 35 36 LVDSA_CLK- NC 33 34 LVDSA_CLK+ GND 31 32 GND NC 29 30 NC NC 27 28 NC GND 25 26 GND NC 23 24 NC NC 21 22 NC GND 19 20 GND NC 17 18 LVDSA_D2- NC 15 16 LVDSA_D2+ GND 13 14 GND LVDSA_D1- 11 12 LVDSA_D0- LVDSA_D1+ 9 10 LVDSA_D0+ GND 7 8 GND LCDSA_DDC_SC 5 6 LCDSA_DDC_SD +3.
