EMX-PNVB Intel® Atom™D525 Processor with ICH8M Chipset Mini ITX Motherboard Quick Installation Guide 1st Ed – 11 September 2013 Part No.
EMX-PNVB Quick Installation Guide FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
EMX-PNVB Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EMX-PNVB Quick Installation Guide 2.
EMX-PNVB Quick Installation Guide 2.
EMX-PNVB Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
EMX-PNVB Quick Installation Guide Connectors Label Function Note FPANEL1 Front Panel Switches 2 x 8 header, pitch 2.54 mm MPCIE1 PCIE signal selector PCI1 PCI slot COM1 Serial port 1 connector COM2~6 Serial port 2~6 connector 2 x 5 header, pitch 2.00 mm JGPIO1 General Purpose I/O 2 x 6 header, pitch 2.54 mm LVDS1 LVDS connector 2 x 20 wafer, pitch 1.25 mm SATA1~2 Serial ATA connector 1~2 USB LAN_A1~2 USB & LAN port 1~2 F_USB1~2 USB connector 1~2 2 x 5 header, pitch 2.
EMX-PNVB Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Normal* Clear CMOS * Default 2.3.
EMX-PNVB Quick Installation Guide 2.3.3 Jumper for COM2 or IR selection (JIR1~2) COM2* JIR2 JIR1 IR Define 1-2 COM2 2-3 IR Note: IR is not functional. * Default 2.3.4 Pin Jumper for LVDS PWR selection (JP1) 3.3V* 5V * Default Pin Define Max current 1-2 3.
EMX-PNVB Quick Installation Guide 2.3.5 Jumper for MPCIE selection (JS1~2) M-SATA* MINIPCIE JS1 JS2 * Default 2.3.6 Pin Pin Define 1-3 2-4 M-SATA 3-5 4-6 MINIPCIE Jumper for MPCIE PWR selection (JS3) 3.3V* GND * Default 10 EMX-PNVB Quick Installation Guide Pin Define 2-3 GND 1-2 3.
EMX-PNVB Quick Installation Guide 2.3.7 Serial port 1~6 or RI, USE JC11/21/31/41/51/61 PIN 9 selector (JC12/22/32/42/52/62) RI* JC22 JC32 JC42 JC52 JC62 USE JC11_JC61 JC12 PIN Option Define CLOSE RI OPEN USE JC11_JC61 * Default 2.3.
EMX-PNVB Quick Installation Guide 2.3.9 General Purpose I/O (JGPIO1) Signal 2.3.
EMX-PNVB Quick Installation Guide 2.3.11 LVDS connector (LVDS1) Signal Note: Mapping connector DF13-40DS-1.25C (1.0mm).
EMX-PNVB Quick Installation Guide 2.3.12 VGA connector (JVGA2) Signal PIN PIN Signal DDC_CLK 10 9 DDC_DATA VSYNC 8 7 HSYNC BLUE 6 5 GND GREEN 4 3 GND RED 2 1 GND Note: It can only use either D-SUB connector or Pin Header 2.3.
EMX-PNVB Quick Installation Guide 2.3.14 Front Panel Audio Connection Header (F_AUDIO) Signal PIN PIN Signal AUD_RET_L 10 9 FRONT_OUT_L 7 NC AUD_RET_R 6 5 FRONT_OUT_R 5V 4 3 VREF_OUT GND 2 1 FRONT_MIC Note: Please use the attached audio cable for front audio daughter board.
EMX-PNVB Quick Installation Guide 2.3.15 Serial port 2~6 connector (COM2~6) COM2 COM3 COM4 COM5 COM6 2.3.
EMX-PNVB Quick Installation Guide 2.3.17 2.3.
EMX-PNVB Quick Installation Guide 2.3.
EMX-PNVB Quick Installation Guide 2.3.20 Keyboard & Mouse connector (JKB_MS) 2.3.
EMX-PNVB Quick Installation Guide 2.3.22 ATX Power connector (ATXPWR1) Signal 20 EMX-PNVB Quick Installation Guide PIN PIN Signal +3.3V 1 11 +3.3V +3.
