EPI-QM57 Intel® Calpella EPIC Module with Intel® QM57 Quick Installation Guide 2nd Ed – 14 March 2012 Part No.
EPI-QM57 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges.
Quick Installation Guide 2.
EPI-QM57 2.
Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
EPI-QM57 Connectors Label Function Note BBAT1 Battery connector 2 x 1 wafer, pitch 1.25mm CN1 Audio connector 4 x 1 header, pitch 2.0mm CPU_FAN1 CPU Fan connector 3 x 1 wafer, pitch 2.54mm HD_PWR HD power connector 4 x 1 wafer, pitch 2.50mm IDE1 Primary IDE connector 22 x 2 header, pitch 2.0mm J422/485 Serial port 2 in RS-422/485 mode 3 x 2 header, pitch 2.54mm JBKL1 LCD Inverter connector 1 2 x 1 wafer, pitch 2.0mm JBKL2 LCD Inverter connector 2 5 x 1 wafer, pitch 2.
Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* COMS *Default 2.3.
EPI-QM57 2.3.3 Miscellaneous setting connector (JFP1) Master Slave* *Default Signal PIN PWBT 1, 2 RST# 3, 4 PWR-LED 5, 6 HDD-LED 7, 8 CF SEL Short Master COPEN# 2.3.
Quick Installation Guide 2.3.5 AT/ATX mode select (PWR_MSEL1) AT* ATX * Default 2.3.
EPI-QM57 2.3.7 Audio connector (CN1) 2.3.
Quick Installation Guide 2.3.
EPI-QM57 2.3.
Quick Installation Guide 2.3.11 Serial port 2 in RS-422/485 mode connector (J422/485) Signal PIN PIN Signal GND 6 5 +5V RX+ 4 3 TX+ RX- 2 1 TX- Note: J422/485 is available after modifying the mode of COM2 in BIOS setting. 2.3.
EPI-QM57 2.3.13 LCD Inverter Connector 1/ 2 (JBKL1/ JBKL2) JBKL2 JBKL2 JBKL1 JBKL1 Signal PIN Signal PIN GND 2 +5V 5 +12V 1 BRIGHT 4 BLK_ON 3 GND 2 +12V 1 2.3.13.1 Signal Description – LCD Inverter Connector (JBKL1) Signal Signal Description BRIGHT Vadj = 0.75V ~ 4.25V (Recommended: 4.7KΩ, >1/16W) BLK_ON LCD backlight ON/OFF control signal 2.3.
Quick Installation Guide 2.3.15 Serial port 1/ 2 connector (JCOM1/ JCOM2) JCOM2 JCOM1 2.3.
EPI-QM57 2.3.
Quick Installation Guide 2.3.18 General purpose I/O connector (JDIO1) Signal 2.3.
EPI-QM57 2.3.20 Power connector (PWRCON1) 2.3.21 Signal PIN PIN Signal VIN 4 3 VIN GND 2 1 GND Signal PIN PIN Signal 7 HOLD#_R SPI connector (JSPI1) 18 EPI-QM57 Quick Installation Guide SPI_SI 6 5 SPISO SPI_CLK 4 3 SPI_CS#0 GND 2 1 +3.
Quick Installation Guide 2.3.22 USB connector 4&5/ 6&7 (JUSB1/ JUSB2) JUSB2 JUSB1 Signal PIN PIN Signal +5V 1 2 GND USB_DN4/ 6 3 4 GND USB_DP4/ 6 5 6 USB_DP5/ 7 GND 7 8 USB_DN5/ 7 GND 9 10 +5V Note: Wrong USB cable configuration with your USB devices might cause your USB devices damaged. 2.3.
EPI-QM57 20 EPI-QM57 Quick Installation Guide YA3M 17 18 YA2M YA3P 15 16 YA2P GND 13 14 GND YA1M 11 12 YA0M YA1P 9 10 YA0P GND 7 8 GND SPCLK 5 6 SPDATA +3.3V 3 4 +5V +3.
