EPI-QM77 Intel Chief River QM77 EPIC Module Quick Installation Guide 3rd Ed – 8 January 2013 Copyright Notice Copyright 2013 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No.
EPI-QM77 FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
Quick Installation Guide Content 1. Getting Started ........................................................................................................... 4 1.1 Safety Precautions ................................................................................................ 4 1.2 Packing List ........................................................................................................... 4 2. Hardware Configuration ........................................................................
EPI-QM77 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges.
Quick Installation Guide 2.
EPI-QM77 2.
Quick Installation Guide EPI-QM77 Quick Installation Guide 7
EPI-QM77 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
Quick Installation Guide Connectors Label Function Note BAT1 Battery connector 2 x 1 wafer, pitch 1.25mm CN2 DVI connector CN4 204-pin DDR3 SODIMM CN7 Audio out connector Audio jack CPU_FAN1 CPU Fan connector 4 x 1 wafer, pitch 2.54mm HDMI HDMI connector HD_PWR1 HD power connector 4 x 1 wafer, pitch 2.50mm J422/1 Serial Port 1 connector 3 x 2 header, pitch 2.00mm JAUDIO1 Audio Connector 6 x 2 header, pitch 2.00mm JBKL1 LCD Inverter connector 1 5 x 1 wafer, pitch 2.
EPI-QM77 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT1) Protect* Clear CMOS *Default 2.3.
Quick Installation Guide 2.3.3 AT/ATX mode selector, Front panel & LED settings (JFP1) AT* ATX *Default Signal PIN PWBT 1, 2 RST# 3, 4 PWR-LED 5, 6 HDD-LED 7, 8 Short: AT MODE Open: ATX MODE COPEN# 2.3.
EPI-QM77 2.3.5 Battery connector (BAT1) 2.3.6 Signal PIN GND 2 VBAT 1 Audio connector (JAUDIO1) Signal PIN PIN Signal GND 12 11 MIC_JD LINE1_JD 10 9 LINE2_JD MIC_LIN 8 7 MIC_RIN LINE1_LIN 6 5 LINE1_RIN GND 4 3 GND LINE2_LOUT 2 1 LINE2_ROUT 2.3.6.
Quick Installation Guide 2.3.7 2.3.
EPI-QM77 2.3.9 PS/2 keyboard & mouse connector (JKB/MS1) Signal 2.3.
Quick Installation Guide 2.3.11 Serial Port 1 connector (J422/1) Signal PIN PIN Signal GND 6 5 +5V RX+ 4 3 TX+ RX- 2 1 TX- Note: J422/1 is available after modifying the mode of COM1 in BIOS setting. 2.3.
EPI-QM77 2.3.13 LCD Inverter Connector 1 (JBKL1) JBKL1 Signal PIN +5V 5 BRIGHT 4 BLK_ON 3 GND 2 +12V 1 2.3.13.1 Signal Description – LCD Inverter Connector (JBKL1) Signal Signal Description BRIGHT Vadj = 0.75V ~ 4.25V (Recommended: 4.7KΩ, >1/16W) BLK_ON LCD backlight ON/OFF control signal 2.3.
Quick Installation Guide 2.3.15 2.3.
EPI-QM77 2.3.
Quick Installation Guide 2.3.
EPI-QM77 2.3.19 General purpose I/O connector (JDIO1) Signal 2.3.
Quick Installation Guide 2.3.21 SPI connector (JSPI1) Signal 2.3.22 PIN PIN Signal 7 HOLD# SPI_SI 6 5 SPI_SO SPI_CLK 4 3 SPI_CS0# GND 2 1 +V3.3M_SPI Signal PIN PIN Signal USBVCC4 1 2 GND USB_PN_Z_4 3 4 GND USB_PP_Z_4 5 6 USB_PP_Z_5 GND 7 8 USB_PN_Z_5 GND 9 10 USBVCC4 USB connector 4&5 (JUSB1_1) Note: Wrong USB cable configuration with USB devices might damage USB devices.
EPI-QM77 2.4 Installing the CPU 2.4.1 Locate the CPU socket on the board. Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left.
Quick Installation Guide 2.4.2 Separate CPU cooler and its base first by screw drawer 1.
EPI-QM77 2. turn the CPU lock clockwise to lock CPU The CPU fits in only one correct orientation.
