EPM-1712 Vehicle 100Watt Smart DC/ DC Converter Quick Installation Guide 1st Ed – 13 January 2011 Part No.
EPM-1712 Quick Installation Guide FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
Quick Installation Guide A Message to the Customer Avalue Customer Services Each and every Avalue’s product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Avalue device is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Avalue has come to be known.
EPM-1712 Quick Installation Guide Technical Support We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult the user’s manual first. To receive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.
Quick Installation Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EPM-1712 Quick Installation Guide 2.
Quick Installation Guide 2.
EPM-1712 Quick Installation Guide 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3.
Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.
EPM-1712 Quick Installation Guide 2.3.2 Low Battery signal setting (JSET2) *Default 12V* 2.3.3 24V Signal PIN 10.6V 1 COM 2 21.
Quick Installation Guide 2.3.4 2.3.
EPM-1712 Quick Installation Guide 2.3.6 Low Battery LED signal Connector (JLED1) Signal PIN +5V 1 BAT LOW Signal 2 LED Status (See Page 15) 2.3.
Quick Installation Guide 2.3.8 System connector (JPC1) Signal PIN Alarm-OUT for Software 5 Debug 5VSB-OUT 4 PWR-SW-OUT1 to Motherboard power on 3 pin. (PS_ON or GND) PWR-SW-OUT2 to Motherboard power on 2 pin. (PS_ON or GND) 1 GND ALARM-Out / 5VSB-out LED Status (See Page 15) 2.3.
EPM-1712 Quick Installation Guide 2.3.
Quick Installation Guide 2.4 Operation Mode explained Delay mode Condition = Auto on 1) Ignition=OFF. Nothing happens. EPM-1712 is waiting for ignition signals. 2) Ignition=ON. EPM-1712 waits for 10 seconds then turns on the 5VSB rail. After another second EPM-1712 sends an “ON” signal to the motherboard via the 2 wires connected to the motherboard’s ON/OFF pins. The motherboard will turn ON and your system should start booting.
EPM-1712 Quick Installation Guide 16 EPM-1712 Quick Installation Guide
