EPS-QM87 Fanless Intel® 4th Generation Core™ i7/i5/i3 Rugged Embedded System with Intel® QM87 Chipset Quick Reference Guide 1st Ed –17 October 2014 Copyright Notice Copyright 2014 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No.
EPS-QM87 FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
Quick Reference Guide Content 1. Getting Started ............................................................................................................ 5 1.1 1.2 1.3 1.4 Safety Precautions ................................................................................................ 5 Packing List ........................................................................................................... 5 System Specifications ......................................................................
EPS-QM87 2.4.15 Intel Front Panel connector (INTBTN1) ................................................................................. 29 2.4.16 Chassis Intrusion connector (CASEOPEN1) ......................................................................... 29 2.4.17 Serial port 1-4 connector (COM1-4) ...................................................................................... 30 2.4.18 Serial port 5-8 connector (COM5-8) ....................................................................
Quick Reference Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
EPS-QM87 1.3 System Specifications Component Mother Board ESM-QM87 + EAP-CE02 Intel® Core™ i7-4700EQ, 4-Core, 2.4GHz, 6M Cache CPU Intel® Core™ i5-4422E, 2-Core, 1.8GHz, 3M Cache Intel® Core™ i3-4110E, 2-Core, 2.
Quick Reference Guide Fanless Fanless Reliability EMI Test CE FCC Class A Dust and Rain Test IP 30 Vibration Test With SSD/mSATA: 5Grms, IEC 60068-2-64, Random,10 ~ 500Hz, 1hr/axis Mechanical Shock Test With SSD/mSATA: 50G, IEC 60068-2-27, Half Sine, 11ms Drop Test -10 ~ 60°C (w/SSD), Ambient w/Air Flow; i5/i3 -10 ~ 50°C (w/SSD), Ambient w/Air Flow; i7 EPS-QM87 Quick Reference Guide 7
EPS-QM87 1.4 System Overview 1.4.1 Front View 1.4.
Quick Reference Guide Reset Reset button LAN1 RJ-45 Ethernet 1 LAN2 RJ-45 Ethernet 2 Audio Jack MIC IN, LINE OUT and LINE IN LPT LPT connector DP DP connector Power System power switch USB USB 2.0 connector x 4 USB 3.
EPS-QM87 1.5 System Dimensions 1.5.
Quick Reference Guide 2. Hardware Configuration Jumper and Connector Setting, Driver and BIOS Installing For advanced information, please refer to: 1- ESM-QM87 Quick Installation Guide or User’s Manual 2- EAP-CE02 and AUX-036/ AUX-037 (Optional)/ AUX-049 (Optional) included in this manual. Note: If you need more information, please visit our website: http://www.avalue.com.
EPS-QM87 2.1 EPS-QM87 connector mapping 2.1.1 DC power-in connector (DC-IN) + G Note: Phoenix and Lockable DC Jack can’t be used at the same time. 2.1.2 External Serial Port 1/2/3/4/5/6/7/8 connector (COM1/2/3/4/5/6/7/8) In RS-232 Mode Signal PIN PIN Signal DCD 1 6 DSR RxDD 2 7 RTS TxDD 3 8 CTS DTR 4 9 RI GND 5 In RS-422 Mode Signal Note: COM5, 6, 7, 8 can be changed to RS-422 and 485 through the BIOS setup.
Quick Reference Guide 2.1.3 External LPT connector (LPT1) Signal PIN PIN Signal STB1 14 LPT_AFD# PD0 2 15 LPT_ERR# PD1 3 16 LPT_INIT# PD2 4 17 LPT_SLIN# PD3 5 18 GND PD4 6 19 GND PD5 7 20 GND PD6 8 21 GND PD7 9 22 GND LPT_ACK# 10 23 GND LPT_BUSY 11 24 GND LPT_PE 12 25 GND LPT_SLCT 13 2.1.
EPS-QM87 2.1.5 Digital I/O connector (GPO1) Signal GPO0 GPO1 GPO2 GPO3 GPO4 GPO5 GPO6 GPO7 GND 2.1.
Quick Reference Guide 2.2 EAP-CE02 Overviews 2.2.
EPS-QM87 2.3 EAP-CE02 Jumper & Connector list Jumpers Label JBAT1 SW1 Function Clear CMOS AT/ATX mode selector Note 3 x 1 header, pitch 2.54mm JRI1~8 Serial port 1~8 pin9 signal selector 3 x 2 header, pitch 2.00mm J1218SEL1 SIO ADDRESS selector 3 x 1 header, pitch 2.
Quick Reference Guide 2.4 EAP-CE02 Jumpers & Connectors settings 2.4.1 Clear CMOS (JBAT1) Protect* Clear CMOS *Default 2.4.
EPS-QM87 2.4.3 JRI8 JRI7 JRI6 2 JRI5 JRI1 Serial port 1~8 pin9 signal selector (JRI1~8) Ring* JRI2 JRI3 +12V JRI4 +5V * Default 2.4.
Quick Reference Guide 2.4.
EPS-QM87 Signal PIN PIN Signal Signal PIN PIN Signal GND B31 A31 GND PCIE_RX2+ B61 A61 PCIE_TX2+ SPKR B32 A32 AC/HDA_BITCLK PCIE_RX2- B62 A62 PCIE_TX2- I2C_CK B33 A33 AC/HDA_SDOUT GPO3 B63 A63 NC I2C_DAT B34 A34 NC PCIE_RX1+ B64 A64 PCIE_TX1+ THRM# B35 A35 THRMTRIP# PCIE_RX1- B65 A65 PCIE_TX1- USB7- B36 A36 USB6- WAKE0# B66 A66 GND USB7+ B37 A37 USB6+ WAKE1# B67 A67 NC USB_4_5_OC# B38 A38 USB_6_7_OC# PCIE_RX0+ B68 A68 PCIE_TX0+ USB5- B39 A39 USB4- PCIE
Quick Reference Guide Signal PIN PIN Signal VGA_GRN B91 A91 NC VGA_BLU B92 A92 NC VGA_HSYNC B93 A93 NC VGA_VSYNC B94 A94 NC VGA_I2C_CK B95 A95 NC VGA_I2C_DAT B96 A96 NC NC B97 A97 NC NC B98 A98 NC NC B99 A99 NC GND B100 A100 FAN_PWMOUT B101 A101 GND NC FAN_TACHIN B102 A102 NC NC B103 A103 NC VCC_12V B104 A104 VCC_12V VCC_12V B105 A105 VCC_12V VCC_12V B106 A106 VCC_12V VCC_12V B107 A107 VCC_12V VCC_12V B108 A108 VCC_12V VCC_12V B109 A109 VCC
EPS-QM87 2.4.
Quick Reference Guide Signal PIN PIN Signal Signal PIN PIN Signal GND D31 C31 GND PEG_TX3+ D61 C61 PEG_RX3+ DDI1_PAIR2+ D32 C32 DDI2_CTRLCLK_AUX+ PEG_TX3- D62 C62 PEG_RX3- DDI1_PAIR2- D33 C33 DDI2_CTRLDATA_AUX- NC D63 C63 NC D64 C64 NC DDI1_DDC_AUX_SEL D34 C34 DDI2_DDC_AUX_SEL NC- NC D35 C35 NC PEG_TX4+ D65 C65 PEG_RX4+ DDI1_PAIR3+ D36 C36 DDI3_CTRLCLK_AUX+ PEG_TX4- D66 C66 PEG_RX4- DDI1_PAIR3- D37 C37 DDI3_CTRLDATA_AUX- GND D67 C67 NC NC D38 C38 DDI3_DDC_AUX_SEL
EPS-QM87 Signal PIN PIN Signal PEG_TX12+ D91 C91 PEG_RX12+ PEG_TX12- D92 C92 PEG_RX12- GND D93 C93 GND PEG_TX13+ D94 C94 PEG_RX13+ PEG_TX13- D95 C95 PEG_RX13- GND D96 C96 GND NC D97 C97 NC PEG_TX14+ D98 C98 PEG_RX14+ PEG_TX14- D99 C99 PEG_RX14- GND 24 D100 C100 GND PEG_TX15+ D101 C101 PEG_RX15+ PEG_TX15- D102 C102 PEG_RX15- GND D103 C103 GND VCC_12V D104 C104 VCC_12V VCC_12V D105 C105 VCC_12V VCC_12V D106 C106 VCC_12V VCC_12V D107 C107 VCC_12V
Quick Reference Guide 2.4.7 SATA Power connector 1/2/3/4 (SATAPWR1/2/3/4) SATAPWR4 SATAPWR3 Signal PIN GND 1 +5V 2 SATAPWR1 SATAPWR2 2.4.
EPS-QM87 2.4.9 2.4.
Quick Reference Guide 2.4.11 2.4.
EPS-QM87 2.4.13 2.4.
Quick Reference Guide 2.4.15 2.4.16 Intel Front Panel connector (INTBTN1) Signal PIN PIN Signal GND 1 2 EXT_PWRBTN# GND 3 4 SYS_RERST# Chassis Intrusion connector (CASEOPEN1) Signal PIN GND 1 +3.
EPS-QM87 2.4.
Quick Reference Guide 2.4.
EPS-QM87 2.5 Daughter Boards (AUX-036 – AUX-037 – AUX-049) 2.5.1 AUX-036 Connectors Label Function PCI1/2 PCI connector 1/2 2.5.2 Note AUX-037 (optional) Connectors Label Function PCI PCI connector 1 PCIe PCI Express X16 connector 2.5.
Quick Reference Guide 2.6 Chassis Intrusion Sensor BIOS Installing (EPS-QM87) Item Option Case open Disabled Enabled Description Enable: Showing message on the screen that “Alert! Cover was previously removed.”When the system is turn on next time. 2.7 Installing Mounting Brackets (EPS-QM87) Step 1. Locate brackets on both sides, matching the holes on the system. Step 2. Insert and fasten 4 screws on each side of the system to secure Mounting brackets.
EPS-QM87 2.8 Installing Hard Disk & Memory (EPS-QM87) Step 1. Step 2. Remove 9 screws from the bottom of your system. Remove the chassis cover. Step 1. Step 2. Step 3. Step 4. Step 5. properly. Remove 8 screws to release the HDD bracket. Slide HDD into its bracket until properly seated. Secure HDD by means of 8 screws. Connect necessary cables to the HDD.
Quick Reference Guide 2.9 Installing PCI devices (EPS-QM87) Step1. Remove 2 screws to release the retention clip Step2. Remove one screw to release the retention clip. Step3. The retention clip can now be removed to open slot cover for PCI installation.