OPM-CDV Fanless Open Pluggable Module Compliant with Intel® Open Pluggable Specification Quick Reference Guide 1st Ed –16 July 2012 Copyright Notice Copyright 2012 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No.
OPM-CDV CONTENT 1. Getting Started ............................................................................................................ 3 1.1 1.2 1.3 1.4 2. Safety Precautions ................................................................................................ 3 Packing List ........................................................................................................... 3 System Specifications ................................................................................
Quick Reference Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
OPM-CDV 1.3 System Specifications Component Mother Board EQM-CDV with EAP-OPI board CPU Intel Cedarview-M N2600/N2800 Memory Onboard 1GB DDR3 800/1066 Power Supply 12~19V (from monitor) System Fan Fanless Wireless LAN Optional Wireless 802.11 b/g/n (via mPCIe or USB) Operating System Windows/ Linux Storage Hard Disk Drive Support 2.5” SATA HDD Solid State Drive Support 2.5” SATA SSD External I/O Serial Port 1 x COM (RS232) USB Port 2 x USB2.
Quick Reference Guide 1.4 System Overview 1.4.1 Front & Top View 1.4.
OPM-CDV 2. Hardware Configuration Jumper and Connector Setting, Driver and BIOS Installing For advanced information, please refer to: 1- OPM-CDV Quick Reference Guide or User’s Manual 2- EAP-OPI included in this manual. Note: If you need more information, please visit our website: http://www.avalue.com.
Quick Reference Guide 2.
OPM-CDV 2.2 OPM-CDV connector mapping 2.2.
Quick Reference Guide 2.3 EAP-OPI Jumper & Connector list Jumpers Label Function Note JFPT1 Miscellaneous setting connector 8 x 1 header, pitch 1.25mm JCMOS1 Clear CMOS 3 x 1 header, pitch 2.00mm JBIOS3 Module/Carrier BIOS selector 3 x 1 header, pitch 2.00mm JRI1 COM1 Dsub_ 9 signal selector 3 x 2 header, pitch 2.00mm JAT_ATX1 AT/ATX power 3 x 1 header, pitch 2.00mm Connectors Label Function Note JBT1 Battery connector 2 x 1 wafer, pitch 1.
OPM-CDV 2.4 Setting Jumpers & Connectors 2.4.1 AT/ATX power (JAT_ATX1) ATX* AT *Default 2.4.
Quick Reference Guide 2.4.3 Miscellaneous setting connector (JFPT1) Signal PIN GND 8 PWRBTN#_IN 7 GND 6 SYSRST# 5 GND 4 PWR_LED+ 3 QC_SATA_LED# 2 HDD_LED+ 1 *Default 2.4.
OPM-CDV 2.4.5 COM1 Dsub_ 9 signal selector (JRI1) +5V Ring* +12V * Default Signal PIN PIN Signal PS2 6 5 +12V PS2 4 3 +5V NRIA# 2 1 JNRIA# Note: When switched to “Ring”, the signal only works in RS-232 mode.
Quick Reference Guide 2.4.6 2.4.7 Battery connector (JBT1) Signal PIN GND 2 +3.
OPM-CDV 2.4.8 2.4.9 Audio connector (JAUD1) Signal PIN PIN Signal MIC_RIN 1 2 MIC_LIN GND 3 4 MIC1_JD LINE1_RIN 5 6 LINE1_LIN LINE1_JD 7 8 GND LPC Connector (JLPC1) Signal 14 OPM-CDV Quick Reference Guide PIN PIN Signal LPC_AD0 1 2 +3.
Quick Reference Guide 2.4.10 SPI connector (JSPI1) Signal PIN PIN Signal +3.
OPM-CDV 2.4.
Quick Reference Guide Signal PIN PIN Signal Signal PIN PIN Signal NC 105 106 NC NC 171 172 NC NC 107 108 NC NC 173 174 NC NC 109 110 NC NC 175 176 NC NC 111 112 NC NC 113 114 NC PCIE0_TX+ 179 180 PCIE0_RX+ NC 115 116 NC PCIE0_TX- 181 182 PCIE0_RX- GND15 117 118 GND16 GND27 183 184 GND28 NC 119 120 NC LPC_AD0 185 186 LPC_AD1 NC 121 122 NC LPC_AD2 187 188 LPC_AD3 NC 123 124 NC LPC_CLK 189 190 LPC_FRAME# NC 125 126 NC SERIRQ 191 192 LPC_LDRQ#
OPM-CDV 2.4.
Quick Reference Guide 2.5 Installing Hard Disk (OPM-CDV) Step 1. Slide HDD into its bracket until properly seated. Step 2. Secure HDD by means of 2 screws. Step 3. Slide in HDD until it’s fully plugged into onboard HDD connector. Step 4. Fasten HDD bracket by means of 2 screws.
OPM-CDV 2.6 Installing PCIE device (OPM-CDV) Step1. Please install mini PCIe device, and fasten with 2 screws Step2.
