SEPC-BYT Fanless Intel® Celeron® Processor J1900 Tiny Box PC Quick Reference Guide 1st Ed – 09 February 2015 Copyright Notice Copyright 2015 Avalue Technology Inc., ALL RIGHTS RESERVED. Part No.
SEPC-BYT FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
Quick Reference Guide otherwise specified. Applications that are described in this manual are for illustration purposes only. Avalue Technology Inc. makes no representation or warranty that such application will be suitable for the specified use without further testing or modification. Life Support Policy Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL OF Avalue Technology Inc. As used herein: 1.
SEPC-BYT Content 1. Getting Started ............................................................................................................ 5 1.1 1.2 1.3 1.4 1.4.1 Front View .................................................................................................................................... 8 1.4.2 Rear View..................................................................................................................................... 8 1.5 1.5.1 2. System Dimensions .......
Quick Reference Guide 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
SEPC-BYT 1.3 System Specifications System CPU Onboard Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz) BIOS AMI uEFI BIOS, 64Mbit SPI Flash ROM I/O Chip System Memory Storage Watchdog Timer H/W Status Monitor Expansion iTE 8772E One 204-pin DDR3L 1333MHz SO-DIMM socket, supports up to 8GB Max 1 x 2.5” Driver Bay, Onboard eMMC 32GB Reset: 1sec. ~ 65535sec./min. and 1sec. or 1min.
Quick Reference Guide SIM card SIM card 1 x SIM Card socket SD card socket SD card socket 1 x SD card socket Environment &Mechanical Power Type Operating Temp. Storage Temp.
SEPC-BYT 1.4 System Overview 1.4.1 Front View Connectors Label Function Line-out Line-out jack Mic-in Microphone-in audio jack VGA VGA connector USB USB 2.0 Type A connector HDD LED HDD LED indicator Power LED Power LED indicator Note D-sub 15-pin, female SD Card Socket SD/MS/MMC socket 1.4.
Quick Reference Guide Power Power on button DC-in DC power-in connector HDMI HDMI connector LAN1 Gigabit LAN (RJ-45) connector SMA connector 1 SMA connector (Default) SMA connector 2 SMA connector (Optional) USB 1 X USB 2.0 Type A connector 1 X USB 3.
SEPC-BYT 1.5 System Dimensions 1.5.
Quick Reference Guide 2. Hardware Configuration Please refer to SENX-BYT User’s Manual for advanced information. Note: If you need more information, please visit our website: http://www.avalue.com.
SEPC-BYT 2.1 SEPC-BYT connector mapping 2.1.1 VGA connector (VGA) PIN Signal PIN Signal PIN Signal 1 R 6 GND 11 NC 2 G 7 GND 12 DATA 3 B 8 GND 13 HSYNC 4 NC 9 +5V 14 VSYNC 5 GND 10 GND 15 CLK 2.1.
Quick Reference Guide 2.1.3 Gigabit LAN (RJ-45) connector (LAN) Speed Speed Status Description Speed Speed Status Description Note: This port allows Gigabit connection to a Local OFF No Light OFF Orange Linked Green Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications.
SEPC-BYT 2.2 Installing Hard Disk & Memory Step1. Unfasten 4 screws to remove the back cover.
Quick Reference Guide Step2. Insert the HDD & Memory and fasten 4 screws. Step3. Assemble the back cover back as step 2 to step 1.
