INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Model Number/ No. De Modelo: BD7000 Beer Dispenser Dispensador / Enfriador de Cerveza BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. La sección en español empieza en la página 23. Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice. Avanti Products, A Division of The Mackle Co., Inc. P.O. Box 520604 - Miami, Florida 33152 www.avantiproducts.
Table of Contents Appliance Safety 3 Important Safeguides 4 Help Us Help You 5 Parts and Features 6–7 Important Safety Instructions 8 Installation Instructions 8 Before Using Your Appliance 8 Installation of Your Appliance 8 Electrical Connection 9 Reversing the Door Swing of Your Appliance 10 Installing and Assembling Your Appliance 10 – 14 Converting Your Beer Dispenser to an ALL-Refrigerator Unit 14 Operating Your Appliance 15 Temperature Control 15 Defrosting Your Appliance
BEER DISPENSER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual for your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words” DANGER”, “WARNING” or “CAUTION”.
IMPORTANT SAFEGUIDES Before the appliance is used, it must be properly positioned and installed as described in this manual,so read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precaution, including the following: Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an extension cord. Replace all panels before operating.
HELP US HELP YOU... Read this guide carefully. Write down the model and serial numbers. It is intended to help you operate and maintain your new Beer Dispenser properly. You'll find them on a plate located on the rear wall of the Beer Dispenser. Keep it handy to answer your questions.
PARTS AND FEATURES 1 2 3 4 5 6 Beer Tower Safety Guard Rail Drip Tray Adjustable Temperature Control Pressure Regulator Evaporator 7 8 9 10 11 12 6 Stainless Steel Door CO2 Tank Holder CO2 Tank Keg Support Plate Leveling Leg Standard Leg
PARTS / ACCESSORIES - DETAILED Accessories 1. Keg Coupler 2. Back Flow Stopper 3. Rubber Washer 4. CO2 Rubber Directional Washer 5. Beer Tower Washer 6. Beer Tower Tap/Beer Hose Assembly 7. CO2 Regulator 8. High Pressure Washer 9. CO2 Tank Valve 10. Guard Rail 11. Drip Pan Top 12. Drip Pan 13. Rubber Foot 14. Keg Support Plate 15. Metal Washer 16. Caster with Brake (Optional – Sold Separately) 17. Casters (Optional – Sold Separately) 18. CO2 Tank Strap 19. Air hose Wing Nut Washer 20. Air Hose 21.
IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electrical shock, or injury when using your Beer Dispenser, follow these basic precautions: Read all instructions before using the unit. DANGER or WARNING: Risk of child entrapment. Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are still dangerous . . . even if they will “just sit in the garage a few days”. Before you throw away your old unit: Take off the door.
questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center. After plugging the appliance into a wall outlet, allow the unit to cool down for 2-3 hours before placing any contents in the Beer Dispenser compartment. ELECTRICAL CONNECTION Warning Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center.
Reversing the Door Swing of Your Appliance This appliance has the capability of the door opening from either the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please call service for reversal instructions. INSTALLING AND ASSEMBLING YOUR APPLIANCE Casters with Brake (OPTIONAL ACCESSORIES) Installation THESE CASTERS ARE NOT INCLUDED WITH YOUR UNIT.
Beer Keg Installation Sketch Installation of CO2 Regulator Attach the CO2 regulator to the cylinder by turning the regulator nut onto cylinder valve, making sure washer is securely inserted into connecting nut. Tighten snug using an adjustable wrench (not supplied) and assure there are no leaks. (See Figure 1) Figure 1 Installation Of CO2 Air Line Hose To Regulator Attach the open end of the red hose to the hose barb connection on the regulator.
Installation Of CO2 Tank Fasterner (see illustriation below) Before install he CO2 Tank to it’s position, make sure to attached the Regulator and the CO2 red hose first, securely tightened. The CO2 tank cushion should also be sticked to the bottom of the tank. First buckle the CO2 tank fasterner to one end of the inner lock piece at the right inner side. Then put the CO2 tank in its position for safety lock. Pull tight the fasterner and buckle the other end into the lock piece.
Connecting the beer tower to coupler Make sure the washer is properly inserted into the wing nut. Place wing nut into the top of the coupler turning until tight. How To Tap A Keg Of Beer Make sure the beer tower faucet is in the closed position. Pull tapping handle out and press downward until it locks into position. (See Figure 8) The keg is now tapped. Opening The CO2 Cylinder Main Valve Before doing that, make sure the secondary shut-off valve is closed, as shown in figure 9.
Spanner Faucet Wrench Spanner faucet wrench provided for either removing or tightening connection Plastic Faucet Lever Attach the black plastic lever (pull handle) provided on the top of the faucet by tighten it by hand clockwise until the end, holding in the process the silver snug underneath so it does not move. If there is still a small drip from the faucet, you may have tightened the plastic lever too much and may need to unscrew silver snug counterclockwise (as shown) one turn.
OPERATING YOUR BEER DISPENSER Setting The Temperature To start, turn the temperature control knob to the maximum setting (6) to achieve coldest position quickly. Allow the unit to run for 3 hours. Temperature range of the thermostat goes from 36°F to 45°F (2ºC to 7ºC). Optimum temperature for serving draught beer is between 36°F – 38°F (2ºC – 3ºC) and that is a key factor to consider in storing and dispensing draught beer. To turn off the Beer Dispenser, turn the control knob to the “OFF” position.
DRAUGHT BEER TROUBLE GUIDE CLOUDY BEER When beer in glass appears hazy, and not clear. Causes Corrections 1 Over chilling beverage cooler and/or beverage lines. Excessive low temperatures may cause hazy, cloudy beer, particularly when beer lies in cold coil for long periods of time. Make certain that lines are thoroughly cleaned, and then raise temperature slightly. 2 3 Cracking, or when partially opening beer faucet. Contaminated air source.
FLAT BEER Foamy head disappears quickly: beer lacks usual zestful brewery fresh flavor. 1 Causes Greasy glass 2 Improper drawing of beer into glass. 3 4 Not enough pressure. Defective Thomas and Tongue Vents. Pressure is shut off. 5 Pre-color, or beer system, too cold. 6 Sluggish pressure regulators. 7 Contaminated air source. Oil or grease fumes. Moisture in Air system. Rapid movement of air.
OFF-TASTE BEER Often bitter and bitey, sometimes completely odor, carrying an unpleasant taste. Beer lines should be flushed after each barrel is empty. Maintain fresh, Clean, sanitary conditions at bar. Smoke, kitchen odors, fly sprays, and disinfectants will harm the tast and flavor of beer, making it unpalatable. These conditions, as described, may come from an air source, or from actual contact with the glass at bar. 1 Causes Improper, or no cleaning of coils, hose, leads, and direct draw system.
WILD BEER Beer, when drawn, is all foam, or too much foam, and not enough liquid beer. Cause Corrections 1 Improper drawing beer into glass. Open faucet quickly and completely. Check and find the correct distance to hold glass from faucet when drawing. Proper foam should be a tight, creamy head, and the collar on the average glass should be ¾ “ to 1” high. 2 Yeast growth, or other obstructions in faucet. Worn faucet parts and worn faucet washers.
11 12 Not enough pressure. No pressure. Old Beer. Check for defective air vents. (see Flat Beer, Corrections #3 and 4.) Always turn pressure on before drawing beer. Rotate stock. The oldest beer should be tapped first; if beer has been allowed to stand in warm temperature beyond 45°F for any excessive length of time, it may begin secondary fermentation. Store beer at 40° all year round.
PROBLEMS WITH YOUR BEER DISPENSER? You can solve many common Beer Dispenser problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. TROUBLESHOOTING GUIDE PROBLEM Beer Dispenser does not operate. Turns on and off frequently. Vibrations. The Beer Dispenser seems to make too much noise. The door will not close properly. POSSIBLE CAUSE Not plugged in. The circuit breaker tripped or blown fuse.
YOUR Avanti Products WARRANTY Staple your sales receipt here. Proof of original purchase date is needed to obtain service under warranty. WHAT IS COVERED LIMITED ONE-YEAR WARRANTY LIMITED SECOND THROUGH FIFTH YEAR WARRANTY For one year from the date of purchase by the original owner, Avanti Products will, at its option, repair or replace any part of the Beer Dispenser which proves to be defective in material or workmanship under normal use.
INSTRUCCIONES EN ESPAÑOL Para reducir el riesgo de incendio, descarga eléctrica, o daño cuando use su PRECAUCIÓN electrodoméstico, siga las siguientes precauciones. Lea todas las instrucciones antes de usar su electrodoméstico. Peligro o Precaución: Existe el riesgo que los niños queden atrapados. Antes de desechar su dispensador de cerveza usado: Retire la puerta. Deje las repisas en su lugar para evitar que los niños queden atrapados dentro.
lados del electrodoméstico, lo cual permitirá la circulación de aire apropiado para enfriar el compresor. Aleje su Dispensador de Cerveza de la luz solar y de fuentes directas de calor (estufa, calentador, radiador, etc.). Los rayos solares directos pueden malograr la capa acrílica, y las fuentes de calor pueden ocasionar un aumento en el consumo eléctrico. Los ambientes extremadamente fríos pueden afectar la eficiencia del enfriamiento de su dispensador.
instalación. Si pasan 5 años y usted no lo utilizó, devuélvalo al surtidor del gas. 9. NUNCA conecte un recipiente del producto a menos que haya 2 seguros en el sistema de presión: a. Uno en el regulador de CO2 (GAS CARBONICO). b. Uno en el acoplador del producto o en la línea de presión del gas. Instalación del Cilindro de CO2 (GAS CARBONICO) Instale el cilindro completamente cargado en el soporte de metal.
Instalación de la manguera de aire CO2 (GAS CARBONICO) o Una el extremo de la manguera roja a la manguera de conexión en el barril acoplador, conectando la llave dispensadora de cerveza al acoplador. o Asegure la manguera usando el broche de presión de plástico que se proveé, usando alicates para ajustar con grampas. (Vea figura 5) o Cerciórese de que la arandela esté insertada correctamente en la tuerca de ala. o Coloque la tuerca de ala en la tapa del acoplador y dele la vuelta firmemente.
1. 2. 3. 4. 5. 6. Convierta su Dispensador de Cerveza en “Todo un Refrigerador” Gire el control a la posición “OFF”. Cierre la válvula principal en el cilindro de CO2 (GAS CARBONICO). Cierre la válvula de desconexión secundaria en el tubo del regulador. Cierre la conexión entre el barril de la cerveza y el acoplador del barril. Drene cualquier tipo de residuo de cerveza en las vías. Desconecte las vías de cerveza y las vías de aire CO2 (GAS CARBONICO) del barril de cerveza. 7.
CUIDADO Y MANTENIMIENTO Instalación de la puerta del Dispensador de Cerveza El Dispensador de Cerveza tiene la capacidad de poderse abrir no solo por la izquierda sino también por el lado derecho. La unidad viene con una puerta que se abre por la izquierda. Como Cambiar la Direccion de Apertura de la Puerta En caso de que necesite cambiar el lado de apertura de la puerta, por favor consulte al servicio posventa de su localidad o al empleado que le vendió la unidad.
CERVEZA TURBIA La bebida no se muestra cristalina CAUSAS La temperatura del nivel de enfriamiento de las bebidas está muy baja CORRECCIONES La nubosidad en la cerveza es causada por excesiva baja temperatura, particularmente cuando la cerveza permanece recostada en el espiral por un periodo de tiempo largo. Verifique que las líneas estén perfectamente limpias, y suba ligeramente la temperatura. Crujidos o cuando se abre parcialmente el grifo del dispensador Abra el grifo rápido y completamente.
CERVEZA SIN CUERPO La espuma desaparece rápidamente, la cerveza carece de su acostumbrado sabor fresco CAUSAS CORRECCIONES Vasos grasosos No lavar los vasos cerveceros junto con vasos que hayan contenido leche, o cualquier tipo de sustancia grasosa. Las pinturas de labios contienen una sustancia grasosa, asegúrese de que se retire bien al lavar los vasos. El exceso de gérmenes deja una película de grasa en los vasos, lo que ocasiona que la cerveza pierda cuerpo inmediatamente.
PERDIDA DE ESPUMA CAUSAS CORRECCIONES La espuma muestra burbujas grandes Esto es generalmente una cerveza sin (como ojos de pescado) o se asienta cuerpo: se deben de seguir las causas y rápido correcciones para cerveza sin cuerpo. CERVEZA SIN SABOR A menudo amargo a veces con olor o sabor desagradable Las vías de la cerveza deben ser enjuagadas después de vaciar cada barril. Mantenga las condiciones sanitarias del bar frescas y limpias.
CERVEZA REBELDE Cuando la cerveza es pura espuma, o demasiada espuma, y no hay casi nada de cerveza líquida CAUSAS La cerveza es vertida inapropiadamente dentro del vaso Acumulación de levadura u otras sustancias en el grifo Partes gastadas de la llave y anillos de la llave desgastados Mangueras torcidas o rajadas: obstrucciones en línea, cerca o detrás del grifo Vías hundidas y con trampas Demasiada presión de aire Exceso CO2 (GAS CARBONICO) No
PROBLEMAS CON SU DISPENSADOR DE CERVEZA Usted puede resolver muchos problemas comunes de su dispensador muy fácilmente, ahorrando el gasto de una posible visita del servicio técnico. Pruebe las siguientes sugerencias para verificar si usted puede resolver el problema antes de llamar al servicio técnico. GUIA PARA SOLUCIONAR PROBLEMAS PROBLEMA SOLUCION Su Dispensador de Cerveza no funciona No está conectado a la corriente eléctrica. El interruptor saltó o se quemó un fusible.
NOTAS: 34
Registration Information Thank you for purchasing this fine Avanti product. Please fill out this form and return it to the following address within 100 days from the date of purchase and receive these important benefits: Avanti Products, A Division of The Mackle Co., Inc. P.O.
VER: 05-04-2010-01 PRINTED IN CHINA 36