Installation Guide

ManualsBrandsAvanti ManualsAppliances24 in. 2.6 cu. ft. Gas Range in Black and Stainless Steel

AVANTI PRODUCTS, LLC

MIAMI, FLORIDA 33172, USA

MADE IN CHINA

GAS RANGE

RESIDENTIAL USE ONLY

INSTALLATION INSTRUCTIONS

IMPORTANT

PLEASE READ AND FOLLOW

Model Numbers:

GR2011CW GRO20P0W

GR2012CB GRO24P0W

GR2013CSS

GR2414CW DGR20P3S

GR2415CB DGR24P3S

GR2416CSS

4009900

Conforms to ANSI STD

Z21.1-2016

Certified to CSA Std.

1.1-2016

Household Gas

Appliances

IMPORTANT - PLEASE READ AND FOLLOW

•

Before beginning, please read these instructions completely and carefully.

•

Do not remove permanently affixed labels, warnings, or plates from the product. This

may void the warranty.

•

Please observe all local and national codes and ordinances.

•

Please ensure that this product is properly grounded.

•

The installer should leave these instructions with the consumer who should retain

for local inspector’s use and for future reference.

•

The electrical plug should always be accessible

Installation must conform with local codes or in the absence of codes, the National Fuel Gas

Code ANSI Z223.1 / NFPA 54 - Latest Edition. Electrical installation must be in accordance

with the National Electrical Code, ANSI / NFPA 70 - latest edition and/or local codes.

INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform

with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

[formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD

(Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home

Installations, ANSI / NCSBCS A225.1, or with local codes where applicable.

INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with

state or other codes or, in the absence of such codes, with the Standard for Recreational

Park Trailers, ANSI A119.5.

Installation of any gas-fired equipment should be made by a licensed plumber. A manual

gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas

stream for safety and ease of service.

If an external electrical source is utilized, the appliance, when installed, must be electrically

grounded in accordance with local codes or, in the absence of local codes, with the national

Electrical Code, ANSI / NFPA 70.

This range is supplied with a protective film on steel and aluminum parts.

This film must be removed before installing / using the appliance.

FOR INSTALLER ONLY

THIS RANGE IS FOR RESIDENTIAL USE ONLY

Summary of content (20 pages)

PAGE 1
AVANTI PRODUCTS, LLC MIAMI, FLORIDA 33172, USA MADE IN CHINA GAS RANGE RESIDENTIAL USE ONLY Model Numbers: INSTALLATION INSTRUCTIONS GR2011CW GR2012CB GR2013CSS GRO20P0W GRO24P0W IMPORTANT PLEASE READ AND FOLLOW GR2414CW GR2415CB GR2416CSS DGR20P3S DGR24P3S 4009900 Conforms to ANSI STD Z21.1-2016 Certified to CSA Std. 1.1-2016 Household Gas Appliances IMPORTANT - PLEASE READ AND FOLLOW • • • • • • Before beginning, please read these instructions completely and carefully.
PAGE 2
To reduce the risk of tipping the appliance, the appliance must be secured by properly installed anti-tip device packed with the appliance. ALL RANGES CAN TIP INJURY TO PERSONS COULD RESULT INSTALL ANTI-TIP DEVICE PACKED WITH RANGE SEE INSTALLATION INSTRUCTIONS WARNING ! If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
PAGE 3
RATING LABELS Models: GR2011CW / GR2012CB / GR2013CSS DGR20P3S Models: Models: GR2414CW / GR2415CB / GR2416CSS DGR24P3S GRO20P0W / GRO24P0W The Governor of California is required to publish a list of substances known to the state of California to cause cancer or reproductive harm and requires businesses to warn customers of potential exposures to such substances.
PAGE 4
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. Installation must conform with all local codes. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent or the gas supplier. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
PAGE 5
INSTALLATION INSTRUCTIONS GENERAL INFORMATION 1. Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 - Latest Edition. 2.
PAGE 6
INSTALLATION PROXIMITY TO SIDE CABINETS 1. This range may be installed adjacent to existing 36” (914 mm) high base cabinets ensuring a 20” (508 mm) opening width between the cabinets. Range dimensions: 20” Wide Models 24” Wide Models Width: 19” 9/16 Width: 23 ½ (497 mm) (597 mm) Depth: 23” 3/4 Depth: 23” 3/4 (603.4 mm) (603.
PAGE 7
INSTALLATION PROXIMITY TO SIDE CABINETS GAS AND ELECTRIC CONNECTION 7
PAGE 8
INSTALLATION HOW TO INSTALL THE BACKSPLASH Align the backsplash to rear part of the cooktop. A B As shown in the diagram Secure the backsplash to the cooktop from the back using the Philips head screws provided. As shown in the diagram C Secure the backsplash from the bottom using the Philips head screws provided. As shown in the diagram HOW TO LEVEL THE RANGE The range is equipped with 4 LEVELLING LEGS and may be leveled by screwing or un-screwing the feet with a spanner tool.
PAGE 9
INSTALLATION ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS YOU MUST USE THE ANTI-TIP / STABILITY BRACKET TO PREVENT UNIT FROM TIPPING. 1. The anti-tip bracket has to be attached as shown on figure below (only rear right side), it has to be fixed on the floor and on the rear wall by four (4) suitable screws (not supplied). 2. After fixing the anti-tip bracket, slide range into place. Be sure the rear right foot slides under the anti-tip bracket attached.
PAGE 10
GAS CONNECTION All gas connections must be made according to national and local codes. This gas supply (service) line must be the same size or greater than the inlet line of the appliance. Sealant on all pipe joints must be resistant to the action of LP/Propane gas. The range is equipped for the use with NATURAL gas. It is design-certified by CSA International for NATURAL and L.P. gases with appropriate conversion.
PAGE 11
GAS CONNECTION PRESSURE REGULATOR INSTALLATION Note: THE REGULATOR IS PRE-INSTALLED BY THE FACTORY FOR YOUR CONVENIENCE. THE FOLLOWING INSTRUCTIONS ARE FOR INFORMATION PURPOSES ONLY OR IN THE INSTANCE A PART MUST BE REPLACED. WARNING Check the right positioning of the gas regulator. The arrow on the back of the gas regulator must be oriented toward the connector. 2.
PAGE 12
GAS CONNECTION ATTENTION: The regulator is pre-installed by the factory for your convenience. The following instructions are for information purposes only or in the instance a part must be replaced. ALL REPAIR / PART REPLACEMENTS AND CONNECTIONS MUST BE DONE BY AN EXPERIENCED LICENSED PROFESSIONAL. WARNING Check the right positioning of the gas regulator. The arrow on the back of the gas regulator must be oriented toward the connector.
PAGE 13
GAS CONVERSION CONVERSION FROM NATURAL GAS (NG) TO PROPANE (LPG) Every range is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the “INJECTORS TABLE”. The nozzle diameters, expressed in hundredths of a millimeter, are marked on the body of each injector. Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service company.
PAGE 14
GAS CONVERSION REPLACING THE INJECTORS The following process applies to the following models: GR2011CW / GR2012CB GR2414CW / GR2415CB GR2013CSS GR2416CSS DGR20P3S / DGR24P3S INJECTORS TABLE NOMINAL POWER REDUCED POWER BURNERS BTU / hr BTU / hr Auxiliary (AUX) Semi Rapid Rapid Oven Burner Broil Burner 2500 4300 8000 6500 / 7300 6500 / 6700 2500 4300 8000 6500 / 7300 6500 / 6700 LPG PROPANE GAS Injector By-pass NG NATURAL GAS Injector By-pass (1/100mm) (1/100mm) (1/100mm) (1/100mm) 53 68 90 80
PAGE 15
GAS CONVERSION REMOVING THE OVEN DOOR To facilitate the conversion process for the oven / broiler burners, the door can be removed. Please follow the instructions carefully: a) Open the door all the way. b) Lift the left and right hooks on the hinges. c) Hold the door firmly on each side. d) Gently close the door and lift upward once the hooks touch the door. e) Set the door on a soft flat surface. f) To replace the door, repeat the above steps in reverse order.
PAGE 16
GAS CONVERSION REPLACING THE OVEN / BROILER BURNER INJECTORS The following process applies to the following models: GR2011CW /GR2012CB GR2414CW / GR2415CB GR2013CSS GR2416CSS To replace the OVEN burner injector: a) Lift and remove the lower panel inside the oven. b) Remove the burner securing screws (total 4) (fig. 22) c) Withdraw the burner and rest it inside the oven. Take care as not to damage the wire to the ignition electrode as well as the thermocouple.
PAGE 17
GAS CONVERSION SETTING THE BURNER MINIMUM SETTING When switching from one type of gas to another, the minimum flow rate must also be correct: the flame should not go out even when passing suddenly from maximum to minimum flame. The following process applies to the following models: 1) 2) 3) 4) GR2011CW / GR2012CB / GR2013CSS GR2414CW / GR2415CB / GR2416CSS GRO20P0W / GRO24P0W Light the burner. Set the top burner valve to the minimum position. Remove the knob by pulling straight out.
PAGE 18
ELECTRICAL CONNECTION If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Check with a qualified electrician if you are not sure whether the range is properly grounded. WARNING Do Not ground to a gas pipe. A 120-volt, 60-Hz, AC-only, 15-ampere, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.
PAGE 19
ELECTRICAL CONNECTION GR2011CW/ GR2012CB / GR2013CSS GR2414CW/GR2415CB/GR2416CSS GRO20P0W / GRO24P0W DGR20P3S DGR24P3S 19
PAGE 20
Gas range installation manual 07272016 PRINTED IN CHINA