INSTRUCTION MANUAL Model Number: WCP13 Wine Chiller / Preserver / Dispenser BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Avanti Products has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice. Avanti Products LLC P.O. Box 520604 - Miami, Florida 33152 www.avantiproducts.
TABLE OF CONTENTS Important Safety Instructions 3 Appliance Safety 3 Important Safeguides 4 Help Us Help You … 5 Parts and Features 6 Electrical Connection 7 Extension Cord / Surge Protector 7 Installation Instructions 8 Before Using Your Appliance 8 Installation of Your Appliance 8 Operating Your Appliance Setting the Temperature Control Storage Interior Light 9 Dispensing Your Wine Setting up the Argon Gas regulator Setting up the Wine Dispenser Assembly Adjusting the Bottle Height R
IMPORTANT SAFETY INSTRUCTIONS • • • • • • To reduce the risk of fire, electrical shock, or injury when using your appliance, follow WARNING these basic precautions: Read all instructions before using the Wine Chiller. DANGER or WARNING: Risk of child entrapment. Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are still dangerous . . . even if they will “just sit in the garage a few days”. Before you throw away your old Wine Chiller: Take off the door.
IMPORTANT SAFEGUIDES Before the appliance is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precaution, including the following: • • • • • • • • • • • • • • • • • • Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an extension cord. Replace all panels before operating.
HELP US HELP YOU... Read this guide carefully. Write down the model and serial numbers. It is intended to help you operate and maintain your new Wine Chiller properly. You'll find them on a plate located on the rear outside wall of the Wine Chiller. Keep it handy to answer your questions.
PARTS & FEATURES 1 2 3 4 5 6 7 Dispenser control Dispensing assembly Argon regulator Dispensing bottle Top hinge Control panel (front of door) Wine shelves (3) 6
ELECTRICAL CONNECTION Warning Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock.
INSTALLATION INSTRUCTIONS BEFORE USING YOUR WINE CHILLER • Remove the exterior and interior packing. • Check to be sure you have all of the following parts: 1 3 1 1 1 1 Instruction Manual Shelves Argon Gas Regulator Replacement Hose for Wine Dispenser Argon Gas Cartridge Spacer Pad • Clean the interior surface with lukewarm water using a soft cloth. • INSTALLATION OF YOUR WINE CHILLER • This wine chiller uses thermoelectric refrigeration technology (no compressor).
OPERATING YOUR WINE CHILLER It is recommended you install the wine chiller in a place where the ambient temperature is between 19ºC-24ºC (66ºF-75ºF). If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate.
Setting up the Wine Dispenser Assembly Start by removing the Argon gas regulator from the shelf by removing the tie-wraps. The gas hose (rear hose) should be connected for you by the factory but in the event the hose is not connected to the regulator, simply insert the end of the hose into the pressure coupler, this will create the seal necessary to allow the flow of gas into the dispensing assembly.
Dispensing Wine Dispenser Control Panel Continuous Manual Pour Press this button for a continuous pour. This option should be used when filling a carafe or decanter. Press and hold to continuously dispense. Release button to stop the flow of wine. ** This option should also be used when cleaning the dispensing system, see the section titled, Cleaning your Wine Dispenser System ** on page 12. Dispense by the glass Press this button to dispense wine in 1, 2, or 3 ounce servings.
CARE AND MAINTENANCE • • • • • • • • • • CLEANING YOUR WINE CHILLER Turn off the power, unplug the appliance, and remove all items including shelves. Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. Wash the shelves with a mild detergent solution. Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts.
PROBLEMS WITH YOUR WINE CHILLER? You can solve many common Wine Chiller problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. TROUBLESHOOTING GUIDE PROBLEM Wine Chiller / Dispenser does not dispense or dispenses small amounts of wine or is slow dispensing. Wine Chiller does not operate. Wine Chiller is not cold enough. Turns on and off frequently. The light does not work. Vibrations.
SERVICE FOR YOUR WINE CHILLER We are proud of our customer service organization and the network of professional service technicians that provide service on your Avanti appliances. With the purchase of your Avanti appliance, you can have the confidence that if you ever need additional information or assistance, the Avanti Products Customer Service team will be here for you. Just call us toll-free.
Staple your sales receipt here. Proof of original purchase date is needed to obtain service under warranty. YOUR AVANTI PRODUCTS WARRANTY WHAT IS COVERED – LIMITED ONE-YEAR WARRANTY Avanti Products warrants that the product is free from defects in materials and/or workmanship for a period of twelve (12) months from the date of purchase by the original owner.
Registration Information Thank you for purchasing this fine Avanti product. Please fill out this form and return it to the following address within 100 days from the date of purchase and receive these important benefits: Avanti Products LLC P.O.Box 520604 – Miami, Florida 33152 Protect your product: We will keep the model number and date of purchase of your new Avanti product on file to help you refer to this information in the event of an insurance claim such as fire or theft.
WCP13 – 03-23-2015 PRINTED IN CHINA 17
