Notice

ManualsBrandsAvaya ManualsIP phones0604DBG

Nortel Page 1 of 24

Product Bulletin

Bulletin Number: P-2007-0153-Global-Rev3

Date: 17 October 2007

UNIStim Firmware Release 0604DBG for Phase II IP

Phones (2001, 2002 & 2004), 0621C4J for IP Phone 2007,

and 0623C4D, 0624C4D, 0625C4D and 0627C4D for IP

Phone 1110, 1120E, 1140E and 1150E Respectively

EVISION HISTORY

Date Revision # Summary of Changes

28-JUNE-07 Original bulletin This is the original publication

30-JULY-07 Revision 1 Minor edits and updates

2-AUGUST-07 Revision 2 Remove support for CS1K prior to release 5.0

10-OCTOBER-07 Revision 3

New up-revision of IP Phone 11xx firmware to

reinstate support for CS1K prior to release 5.0

and close PAA-2007-0208-Global

Introduction

Nortel* is pleased to announce the availability of a release of UNIStim firmware version

0604DBG for the Phase II IP Phone 2001, Phase II IP Phone 2002, and Phase II IP Phone

2004. Nortel is also pleased to announce the availability of a release of UNIStim firmware

version 0621C4J for the IP Phone 2007. In addition, Nortel is pleased to announce the

availability of releases of UNIStim firmware version 0623C4D, 624C4D, 0625C4D and

0627C4D for the IP Phone 1110, IP Phone 1120E, IP Phone 1140E and IP Phone 1150E

respectively.

NOTE: The 0623C4D, 0624C4D, 0625C4D and 0627C4D firmware loads, for the IP Phone

1110, 1120E, 1140E and 1150E respectively, resolve an incompatibility discovered in the

0623C4B, 0624C4B, 0625C4B and 0627C4B firmware loads with Communication Server

1000 release 4.5 or earlier. The incompatibility was advertised in PAA-2007-0208-Global.

With the up-revision of 0623C4D, 0624C4D, 0625C4D and 0627C4D firmware loads the

product advisory PAA-2007-0208-Global is closed.

Even though these firmware loads are being released with Communication Server 1000

release 5.0 to deliver enhancements to Nortel’s IP Telephony Solution, these firmware loads

Summary of content (24 pages)

PAGE 1
Product Bulletin Bulletin Number: Date: P-2007-0153-Global-Rev3 17 October 2007 UNIStim Firmware Release 0604DBG for Phase II IP Phones (2001, 2002 & 2004), 0621C4J for IP Phone 2007, and 0623C4D, 0624C4D, 0625C4D and 0627C4D for IP Phone 1110, 1120E, 1140E and 1150E Respectively REVISION HISTORY Date Revision # Summary of Changes 28-JUNE-07 Original bulletin This is the original publication 30-JULY-07 Revision 1 Minor edits and updates 2-AUGUST-07 Revision 2 Remove support for CS1K prior to re
PAGE 2
are also backward compatible with Communication Server 1000 release 4.5 and earlier, albeit without the enhancements. These firmware loads are being released with Communication Server 1000 release 4.5 and earlier to deliver quality improvements inherent in the new firmware that are also beneficial to the earlier releases of Communication Server 1000. These new firmware loads, in association with Communication Server 1000 release 5.0 deliver enhancements to Nortel’s IP Telephony Solution.
PAGE 3
By default, Media Security is enabled on the Nortel Communication Server 1000 release 5.0. For more information about Media Security concepts and implementation in Communication Server 1000 Release 5.0, see Nortel Communication Server 1000 Security Management Fundamentals (NN43001-604). Media Security delivered with Communication Server 1000 Release 5.0 exchanges security keys through UNIStim, using a secure channel.
PAGE 4
The IP Phone displays a slightly different security icon on the IP Phone’s screen to indicate a secure call using SRTP PSK. The security icon for SRTP PSK is a solid padlock symbol in the first position of the first line of the caller display.
PAGE 5
Once the fonts are downloaded, the set needs to know when to use which fonts. The configuration file is used to create this mapping. The mapping will persist until explicitly changed or until a font is removed. The set will validate the mappings (i.e. ensuring that the font file exists) on startup and whenever a mapping change occurs. If a font file is removed the set will revert to the default mappings. Downloaded fonts have a version number to avoid unnecessary downloads and to facilitate upgrades.
PAGE 6
• • • • • • • • • Korean (requires font download) Latvian Norwegian Polish Portuguese Russian Spanish Swedish Turkish The IP phone and call server synchronize the language choice regardless of whether the language selection is made by the call server or locally at the phone. If the Call Server initiates a language change, the IP Phone changes its local prompts to match the specified language on the Call Server.
PAGE 7
More flexible network connectivity control The 0604DBG, 0621C4J, 0623C4D, 0624C4D, 0625C4D and 0627C4D firmware loads introduce greater low level network control available through the phones configuration menus. The greater control includes: 1) Allowing 802.1q extended frame format to be disabled permitting the phone to connect to network infrastructure that does not support the 802.1Q extended frame format. As well, the new firmware allows for the provisioning of the 802.
PAGE 8
The Contrast and Brightness Tools are used to alter the physical settings of the display. The Backlight setting determines the time before the display sleeps (goes black) or dims. Two new short duration intervals of 5 seconds and 1 minute have been added to the existing duration choices. Because of the addition of the two new intervals, a previously selected preference may be adjusted when the new firmware is loaded onto the phone.
PAGE 9
The 0604DBG, 0621C4J, 0623C4D, 0624C4D, 0625C4D and 0627C4D firmware releases close the following cases: Case # 070104-91739 070326-78016 070412-96011 070606-51244 060726-18008 060911-74038 061019-18728 061020-20102 061027-27675 070226-47774 070313-65095 070330-83922 070417-00508 070510-24253 Title CRC errors occurring during large file transfer when using auto negotiation Set cannot be muted with “AnswerBack” on a BCM platform DHCP Release sometimes not being sent XAS IP address may change to 1.1.0.
PAGE 10
Current release of SRTP PSK is not backward compatible with older version of SRTP PSK (Applies to IP Phone 2001, 2002, 2004, 2007, 1110, 1120E, 1140E, 1150E) As stated above, running SRTP using PreShared Keys (PSK) is still a valid option in the IP Phones. But one important note when upgrading the IP Phones to the current releases of firmware is to realize that the current releases of SRTP PSK is not compatible with older versions of SRTP PSK.
PAGE 11
and the PC Ethernet cable (if connecting a PC) to the PC Ethernet port (little computer icon) on the back of the phone. Correction to VLAN Access Process (Applies to IP Phone 2002, 2004, 2007, 1120E, 1140E) – may impact current network configurations The 0604DBG, 0621C4J, 0624C4D and 0625C4D firmware releases continue to support the changes to the VLAN Access Process that were first introduced in 0604D9H, 0621C2B, 0624C1E or 0625C1E firmware.
PAGE 12
Important Note: While these changes corrects the VLAN access process, the change might impact current customer network configurations, especially if something special was done to handle the prior operation of the phone. For more information on VLAN support in the IP Phones, please refer to the IP Phones Description, Installation and Operation Document, NTP 553-3001-368.
PAGE 13
IP Phone Compatibility These firmware releases are compatible with the following IP Phones: PEC NTDU90AA16 NTDU90BA16 NTDU90AA70 NTDU90BA70 NTDU90AB70 NTDU90BB70 NTDU90AC70E6 NTDU90BC70E6 NTDU90BBGS NTDU91AA16 NTDU91BA16 NTDU91AA70 NTDU91BA70 NTDU91AB70 NTDU91BB70 NTDU91AC70E6 NTDU91BC70E6 NTDU91BBGS Nortel Description IP Phone 2001 (Ethergray) with Icon keycaps – Manufacture Discontinued IP Phone 2001 (Ethergray) with English Text label keycaps – Manufacture Discontinued IP Phone 2001 (Charcoal) with I
PAGE 14
NTDU92AA16 IP Phone 2004 (Ethergray) with Icon keycaps – Manufacture Discontinued NTDU92BA16 IP Phone 2004 (Ethergray) with English Text label keycaps – Manufacture Discontinued NTDU92AA70 IP Phone 2004 (Charcoal) with Icon keycaps – Manufacture Discontinued NTDU92BA70 IP Phone 2004 (Charcoal) with English Text label keycaps – Manufacture Discontinued NTDU92AB70 IP Phone 2004 (Charcoal with Bezel) with Icon keycaps – Manufacture Discontinued NTDU92BB70 IP Phone 2004 (Charcoal with Bezel) with English Text
PAGE 15
NTYS05BA IP Phone 1140E Graphite with English keycaps – Manufacture Discontinued NTYS05AC IP Phone 1140E Graphite with Icon Keycaps NTYS05BC IP Phone 1140E Graphite with English keycaps NTYS05ABE6 IP Phone 1140E Graphite with Icon Keycaps (RoHS) – Manufacture Discontinued NTYS05BBE6 IP Phone 1140E Graphite with English Keycaps (RoHS) – Manufacture Discontinued NTYS05BBGSE6 IP Phone 1140E GSA (RoHS) – Manufacture Discontinued NTYS05ACE6 IP Phone 1140E Graphite with Icon Keycaps (RoHS) NTYS05BCE6 IP Phone 11
PAGE 16
Call Server Compatibility and Requirements These firmware releases are compatible with the below Nortel Call Servers. Note that in order to utilize the SRTP USK and the extended language support available in the firmware the IP Phones must be connected to Communication Server 1000 release 5.0 Call Server Notes / Advisements CS 1000 5.00W - IP Line 5.00.31 - SS 5.00.31 Nortel recommends an upgrade to these firmware releases at the earliest opportunity. CS 1000 4.
PAGE 17
SRG 200/400 1.0 (BCM 3.7 based) SRG 200/400 1.5 (BCM 4.0 based) It is mandatory that SRG 1.0 customers upgrade to SRG200/400 Rls1.5 to ensure official support for the latest feature and software application support across the IP Phone portfolio. Nortel recommends an upgrade to these firmware releases at the earliest opportunity. No SRG patches are required to support the Enhanced Firmware Download feature that allows the IP Phone firmware supported on the SRG 200/400 1.
PAGE 18
The IP Phone 1110 and 1150E are not supported on SRG 50 Rls1.0. SRG 50 2.0 Although not required, it is strongly recommended that SRG 50 1.0 customers upgrade to 2.0 to ensure the latest feature and software application support across the IP Phone portfolio Nortel recommends an upgrade to these firmware releases at the earliest opportunity.
PAGE 19
System Compatibility and Requirements System Notes / Advisements Nortel Application Gateway 1000 These firmware releases continue to provide support to interwork with Nortel Application Gateway 1000. The Application Gateway 1000 delivers business applications to the IP Phones. It is an open, standards-based network platform that supports simultaneous voice and data services.
PAGE 20
IP Phone Firmware Upgrade Method (Communication Server Dependent) Communication Server 1000 The IP Phone 2007, 1110, 1120E, 1140E and 1150E supports remote firmware upgrades through both a TFTP process and a more automated UFTP process direct from the Communication Server 1000 Release 4.5 or later. The method to upgrade the IP Phone 2007, 1110, 1120E and 1140E firmware depends on the call server software. • • Communication Server 1000 Release 4.0 and Succession 1000 Release 3.
PAGE 21
IP Phone Configuration Menu The text-based configuration menu has been expanded with the 0623C4D and 0604DBG firmware release on the Phase II IP Phone and IP Phone 1110 respectively. The text-based menu structure below presents the complete configuration menu now available: EAP Enable?[0-N,1-Y]:0 if “1” DeviceID[ ] Password:[*******] LLDP Enable? [0-N,1-Y]:1 DHCP? [0-N,1-Y]:1 if “0” SET IP: xxx.xxx.xxx.xxx NETMSK: xxx.xxx.xxx.xxx DEF GW: xxx.xxx.xxx.xxx S1 IP: xxx.xxx.xxx.
PAGE 22
Duplex[0-A,1-F,2-H]:0 Cfg XAS?[0-N, 1-Y]:1 if “1” XAS IP: xxx.xxx.xxx.xxx Voice 802.
PAGE 23
Enable 802.1x (EAP): [] DeviceID: Password: Enable 802.1ab (LLDP): [] DHCP: [No, Partial, Full] Set IP: xxx.xxx.xxx.xxx Net Mask: xxx.xxx.xxx.xxx Gateway: xxx.xxx.xxx.xxx S1 IP: xxx.xxx.xxx.xxx Port: S1 Action: Retry: S1 PK: FFFFFFFFFFFFFFFF S2 IP: xxx.xxx.xxx.xxx Port: S2 Action: Retry: S2 PK: FFFFFFFFFFFFFFFF Ntwk Port Speed: [Auto, 10BT, 100BT] Ntwk Port Duplex: [Auto, Force Full, Force Half] Disable Voice 802.
PAGE 24
The IP Phone 2007, 1110, 1120E, 1140E and 1150E contain a password protection mechanism to lock out access to the Network Configuration menu. If enabled, access to the Network Configuration menu is password protected and the password is prompted by a pop up window. One must type the password 26567*738 (color*set) from the dial pad and press the Down arrow or mouse click “OK” to enter the Network Configuration menu. When an incorrect password is entered, the Network Configuration Menu is not opened.