Avaya one-X™ Deskphone Value Edition SIP for 1603SW-I IP Deskphones Installation and Maintenance Guide Release 1.
© 2010 Avaya Inc. All Rights Reserved. Notice While reasonable efforts were made to ensure that the information in this document was complete and accurate at the time of printing, Avaya Inc. can assume no liability for any errors. Changes and corrections to the information in this document may be incorporated in future releases. For full legal page information, please see the complete document, Avaya Legal Page for Hardware Documentation, Document number 03-600759.
Contents Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Intended Audience. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Document Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Other Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Customer Support . . . . . . . . . . . . . . . . . . . . .
Contents Self-Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Chapter 4: Maintaining 1603SW-I IP Deskphones . . . . . . . . . . . . . 43 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Downloading Software Upgrades. Download Procedure . . . . . Updating the Settings File. . . Downloading Language Files . Downloading Font Files . . . . . . . . . 43 44 45 45 46 The GROUP System Value . . . . . . . . . . . . . . . . . .
Chapter 1: Introduction About This Guide This guide describes how to install and maintain the Avaya one-X™ Deskphone Value Edition SIP for 1603SW-I IP Deskphone product line and troubleshoot telephone problems. The 1603SW-I IP Deskphones support two signaling protocols, Session Initiation Protocol (SIP) and H.323 protocol. One of the following must be installed to use the 1603SW-I IP Deskphones with the SIP protocol: Note: ● Avaya Aura™ Communication Manager Release 6.
Introduction Intended Audience This document is intended for personnel who install and administer the 1603SW-I IP Deskphones. ! CAUTION: CAUTION: Avaya does not provide product support for many of the products mentioned in this document. Take care to ensure that there is adequate technical support available for the servers involved, including, but not necessarily limited to, HTTP, HTTPS, and DHCP servers.
Other Documentation Other Documentation See the Avaya support site at http://www.avaya.com/support for 1603SW-I IP Deskphone technical and end user documentation. See Appendix C: Related Documentation for a list of non-Avaya documents, such as those published by the Internet Engineering Task Force (IETF) and International Telecommunication Union (ITU). Customer Support For 1603SW-I IP Deskphone support, call the Avaya support number provided to you by your Avaya representative or Avaya reseller.
Introduction 8 Avaya 1603SW-I SIP Deskphones Installation and Maintenance Guide
Chapter 2: 1603SW-I IP Deskphone Installation Introduction The 1603SW-I IP Deskphones use Internet Protocol (IP) technology with Ethernet interfaces. The IP telephones supplement the existing Avaya IP Solutions platform. The 1603SW-I IP Deskphones support DHCP and HTTP/HTTPS over TCP which enhance the administration and servicing of the telephones.
1603SW-I IP Deskphone Installation IP Telephone Models The 1603SW-I telephones have: ● three call appearance/feature buttons ● a two-row by 16-column display The 1603SW-I IP Deskphones also have an internal Ethernet switch that allows the telephone and a PC to share the same LAN connection, if appropriate. Thus, these telephones do not need, or work with, the 30A switched hub interface. This document describes the installation of these telephones and post-installation maintenance issues.
Pre-Installation Checklist Pre-Installation Checklist Before plugging in the 1603SW-I IP Deskphones, verify that all the following requirements are met. Failure to do so prevents the telephone from working properly and can have a negative impact on the network. Print copies of this checklist for each server and deskphone. Verify These Network Requirements 1. Ensure that the LAN uses Ethernet Category 5e cabling running the IPv4 version of Internet Protocol. 2.
1603SW-I IP Deskphone Installation Verify These Network Requirements (continued) 4. The Communication Manager (CM) call server is configured correctly, as described in the Avaya one-X™ Deskphone Value Edition SIP for 1603SW-I IP Deskphones Administrator Guide and Avaya Communication Manager documentation. Both documents are available at http://www.avaya.com/support. 5.
Converting Software on 1603SW-I IP Deskphones 15. Note: IP telephones ship from the factory with H.323 software. Existing installations might also have many IP telephones running H.323 software. For instructions on how to convert between H.323 and SIP software, see Converting Software on 1603SW-I IP Deskphones. Note: The 1603SW-I IP Deskphone does not support headsets. Converting Software on 1603SW-I IP Deskphones 1603SW-I IP Deskphones use either H.323 or SIP software but come from the factory with H.
1603SW-I IP Deskphone Installation Assembling the 1603SW-I IP Deskphones ! CAUTION: CAUTION: Be careful to use the correct jack when plugging in the deskphone. The jacks are located on the back of the deskphone housing and are flanked by icons to represent their correct use. Powering the 1603SW-I IP Deskphones All 1603SW-I IP Deskphoness can be locally powered with a Telephone Power Module (DC power jack), available separately. The DC input rating is 5 VDC, 2A.
Assembling the 1603SW-I IP Deskphones Figure 1 provides an illustration that shows how to connect cords to jacks on 1603SW-I IP Deskphones. Use the illustration and the associated procedure for deskphone assembly.
03SW-I IP Deskphone Installation 1. Plug one end of the first Category 5 modular line cord into the Ethernet jack of the PC and the other end into the secondary Ethernet jack on the 1603SW-I IP Deskphones, if appropriate. 2. Plug one end of the second Category 5 modular line cord into the Ethernet jack on the 1603SW-I IP Deskphones. Plug the other end of this cord into the Ethernet wall jack. If the telephone is to be IEEE-powered, you are finished. Do not proceed to Step 3. 3.
Dynamic Addressing Process/Telephone Startup 1. The telephone activates the Ethernet line interface, the PC Ethernet jack, and dial pad input to allow the invocation of procedures. The activation occurs as soon as possible after power-up or a reset. The telephone displays the speed of the Ethernet interface in Mbps, that is, 10 or 100. The message No Ethernet displays until the software determines whether the interface is 10 Mbps or 100 Mbps.
1603SW-I IP Deskphone Installation 6. When connected, the telephone looks for an upgrade script file. 7. The HTTP/HTTPS server sends and identifies an upgrade script. The GET message might have to be sent several times. Each time the GET message is sent, all IP telephones display one of the following messages: HTTP: n uri For HTTP, n is the number of HTTP requests made by the telephone and uri is the URI for the current HTTP request. 8.
Dynamic Addressing Process/Telephone Startup 11. Enter the extension and press OK. The 1603SW-I IP Deskphones display the following prompt for a password: Login Enter Password Enter Password and press Enter or OK 12. Enter the password and press OK. 13. The extension is visible as you enter it but the password displays as asterisks. The system determines whether the extension is in use. 14. The telephone initiates SIP registration with the proxy server.
1603SW-I IP Deskphone Installation Printing Button Labels You can download software from www.desi.com that enables you to print button labels for the 1603SW-I IP Deskphones. To download this software, perform the following steps: 1. Using your web browser, go to www.desi.com. 2. Click DESI downloads. 3. Download the appropriate application.
Chapter 3: Local Administrative Options Introduction After you have successfully installed a 1603-SWI SIP Deskphone, you might be instructed to administer one of the options described in this chapter. Note: Note: You can modify the settings file to set parameters for deskphones that download their upgrade script and application files from the same HTTP server.
Local Administrative Options 2. Attempts to enter invalid data are rejected, and the telephone emits an error beep. 3. If you enter a numeric digit for a value or for an IP address or subnet mask field after entering only a zero, the new digit replaces the zero. 4. Press the # button to go to the next step. 5. To backspace, press the leftmost softkey. When you press the applicable button or key to backspace, the most recently entered digit or period is erased from the display.
Set the 802.1X Operational Mode Local Programming Option Code See Group Identifier G R O U P (4 7 6 8 7) Group Identifier on page 34. Interface Control I N T (4 6 8) Interface Control on page 35. Event Logging L O G (5 6 4) Disable/Enable Event Logging on page 37. Reset the telephone R E S E T (7 3 7 3 8) Reset System Values on page 39. Restart the telephone R E S E T (7 3 7 3 8) Restart the Telephone on page 40.
Local Administrative Options ● P-t w/Logoff (pass-thru with Logoff) mode if setting = 1 ● Supplicant mode without pass-thru or p-t w/Logoff if setting = 2 2. Perform one of the following steps: ● If you want to change the DOT1X mode value, go to Change the DOT1X Mode Value on page 24. ● If you want to change the DOT1XSTAT mode value go to Change the DOT1XSTAT Mode Value on page 25. Change the DOT1X Mode Value Use the following procedure to change the DOT1X mode value. 1.
Pre-Installation Checklist for Static Addressing Change the DOT1XSTAT Mode Value Use the following procedure to change the DOT1XSTAT mode value. 1. Press #. The following text displays: Supplicant=setting *=change #=OK where the setting is the current value of the system value DOT1XSTAT (802.1X Supplicant Mode), defined as: ● Disabled if setting = 0 ● Unicast only if setting = 1 ● Unicast/multicast if setting = 2 2. To change the mode value, press *.
Local Administrative Options from working. Such errors can also have a negative impact on your network. Print copies of this checklist for each subnet. 1. The IP address of the deskphone. 2. The IP address of the router. 3. The IP subnet mask. 4. The IP address of the HTTP and/or HTTPS server. 5. The IP address of the DNS server. 6. The VLAN ID (the L2QVLAN value). 7. The VLANTEST value.
Static Addressing Installation Static Addressing Installation The usual way to assign IP addresses to IP telephones is the automatic method described in Dynamic Addressing Process/Telephone Startup on page 16. There might be times, however, when manual assignment of IP addresses is desired. ! CAUTION: CAUTION: Static addressing is necessary when a DHCP server is unavailable.
Local Administrative Options 3. Enter the SIP proxy IP address followed by the # button. The telephone displays: Router=nnn.nnn.nnn.nnn New=_ where nnn.nnn.nnn.nnn is the current system value of the router IP address. 4. Enter the router IP address followed by the # button. The telephone displays: Mask=nnn.nnn.nnn.nnn New=_ where nnn.nnn.nnn.nnn is the current system value of the IP netmask. 5. Enter the IP netmask followed by the # button. The telephone displays: FileSv=nnn.nnn.nnn.nnn New=_ where nnn.
Static Addressing Installation 8. Press the # button to continue the procedure without changing the displayed status of 802.1Q The telephone displays the following text: VLAN ID=dddd New=_ where dddd is the current system value of the 802.1 VLAN ID. 9. Enter a valid value between 0 and 4094 for the new value of the 802.1 VLAN ID. The telephone displays the following message: VLAN test=ddd New=_ where ddd is the number of seconds to wait for the DHCPOFFER on a non-zero VLAN. 10.
Local Administrative Options Disable/Enable Automatic Gain Control Use the following procedure to turn automatic gain control for the handset, headset, and/or the Speaker on or off. Note: Note: The user can potentially override the AGC local procedure settings, as described in the telephone user guide. If overridden, the backup file stores the AGC value(s) set by the user and ignores any setting established using this local procedure. 1.
Disable/Enable Automatic Gain Control 4. To change the AGC Headset value from On to Off, press 0. To change the AGC Headset value from Off to On, press 1. One of the following displays, based on the current value of the system value AGCSPKR: If AGCSPKR = 1: Speaker AGC=on 0=off #=OK If AGCSPKR = 0: Speaker AGC=off 1=on #=OK 5. To change the AGC Speaker value from On to Off, press 0. To change the AGC Speaker value from Off to On, press 1.
Local Administrative Options Manually Setting the DHCP Client Hardware Address Use this procedure to manually set or change the Client Hardware Address, if you use static addressing rather than DHCP. 1. While the telephone is on-hook and idle, press the following sequence of keys on the telephone’s faceplate: Mute 2 4 2 3 3 7 # (Mute C H A D D R #) Note: Note: Press the Mute button momentarily. Do not press this button while pressing other keys/buttons.
Clear Procedure Clear Procedure Sometimes, you might want to remove all administered values, user-specified data, and option settings. Essentially, you want to return a telephone to its initial “clean slate” or out of the box condition. This is usually done when passing a telephone to a new, dedicated user when the user’s L O G O F F option is not sufficient. For example, a new user is assigned the same extension, but requires different permissions than the previous user.
Local Administrative Options 3. Press the * button to terminate the procedure without clearing the values. Press the # button to clear all values to their initial default values. A confirmation tone sounds and the following text displays left-justified at the top of the display: Clearing values. The telephone is cleared to its “out of the box” state. Group Identifier Use the following procedure to set or change the Group Identifier.
Interface Control Interface Control Use the following procedure to set or change the interface control value. 1. While the telephone is on-hook and idle, press the following sequence of keys on the faceplate of the telephone: Mute 4 6 8 # (Mute I N T #) Note: Note: Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. 2.
Local Administrative Options 4. Press the * button to terminate the procedure, or the # button to save the new value. If you press the # button, the following text displays: PHY2=status *=change #=OK where status is the value of PHY2STAT, defined as: ● Status is disabled when PHY2STAT = 0 ● Status is auto when PHY2STAT = 1 ● Status is 10Mbps HDX when PHY2STAT = 2 ● Status is 10Mbps FDX when PHY2STAT = 3 ● Status is 100Mbps HDX when PHY2STAT = 4 ● Status is 100Mbps FDX when PHY2STAT = 5 5.
Disable/Enable Event Logging Disable/Enable Event Logging Use the following procedure to enable or disable logging of system events. 1. While the telephone is on-hook and idle, press the following sequence of keys on the faceplate of the telephone: Mute 5 6 4 # (Mute L O G #) Note: Note: Press the Mute button momentarily. Do not press this button while pressing other keys/buttons. 2.
Local Administrative Options 4. Press the * button to terminate the procedure, or the # button to save the new value. If you press the # button, the telephone displays the following text: New value being saved The telephone saves the new value. Logoff Use the following procedure to log off a telephone. ! CAUTION: CAUTION: Once a telephone is logged off, a password and extension might be needed to log back on. 1.
Reset System Values Reset System Values Use the following procedure to reset all system values and system initialization values except AUTH and NVAUTH to the default values. It also resets the 802.1X identity and password to the default values. ! CAUTION: CAUTION: This procedure erases all static information except the extension number and password, without any possibility of recovering the data. 1.
Local Administrative Options 4. If you do not reset the telephone, the telephone displays the following prompt: Restart phone? *=no #=yes 5. Press the * key to terminate the procedure without restarting the telephone. Otherwise, press # and perform the following Restart procedure. Restart the Telephone Use the following procedure to restart the telephone. 1.
Site-Specific Option Number Setting Site-Specific Option Number Setting ! CAUTION: CAUTION: Do not perform this procedure if you are using static addressing. Perform this procedure only if you are using DHCP and the LAN administrator instructs you to do this. Use the following procedure to set the Site-Specific Option Number (SSON). 1.
Local Administrative Options Self-Test Procedure Note: Note: 1603SW-I IP Deskphones store two software code images in reprogrammable non-volatile memory. The primary image, called the “big app” must be running to perform a self-test. The backup image, called the “little app” does not support the self-test. For self-testing, use the following procedure: 1.
Chapter 4: Maintaining 1603SW-I IP Deskphones Introduction This chapter covers the maintaining the 1603SW-I IP Deskphones, for example, downloading a new software version from the Avaya support Web site. Note that the recommended configuration is the latest call server software and the latest IP deskphone firmware. ! Important: Important: You can convert a 1603SW-I IP Deskphone from H.323 to SIP software, or from SIP to H.323 software.
Maintaining 1603SW-I IP Deskphones ● .Binary files with the latest SIP binary code for 1603SW-I SIP IP Telephones. ● Other useful information such as a ReadMe file. All these files are in a self-extracting executable file that comes in both zipped and unzipped format. When the majority of your IP telephones are SIP-based, select the software bundle identified as “SIP” from the Web site. The application files in this SIP software bundle are the same as in the H.323 bundle.
Downloading Software Upgrades Updating the Settings File After checking the application software, the 1603SW-I IP Deskphone looks for a 46xxsettings file. Another important maintenance activity might be to update the settings file for any changes to your customized settings. Checking the Read Me file can provide an indication of the impact of a software upgrade on your current settings.
Maintaining 1603SW-I IP Deskphones Downloading Font Files The font file must be stored in the same location as the 46xxsettings file or under the HTTP Server directory, defined using the SET HTTPDIR_HTTP server directory path command. You can download a new font tile version only if the filename differs from the font file previously downloaded. Alternately, you can remove the old font file using an empty SET FONTFILE command in the 46xxsettings file before downloading a font file with the same filename.
Chapter 5: Troubleshooting Guidelines Introduction This chapter describes problems that might occur during both installation and normal operation of the 1603SW-I SIP Deskphone and possible ways of resolving these problems. This chapter contains the following sections: ● Descriptions of error conditions and methods for resolving them. ● The use of the V I E W option to view system values. ● Error and status messages, and methods for resolving them.
Troubleshooting Guidelines DTMF Tones SIP desjphones send DTMF tones according to the SEND_DTMF_TYPE parameter setting. The default setting of this parameter sends DTMF “tones” as “telephone event” RTP packets per RFC 2833. Whether a non-SIP telephone hears these DTMF tones depends on whether the Avaya Communication Manager media resource converts the “telephone event” RTP packets into audio RTP packets.
The View Administrative Option Note: Note: Press the Mute button momentarily. Do not press this key while pressing other keys. The following text displays left-justified at the top of the display: View settings *=next #=exit 2. Press the * button at any time during viewing to display the next name and system value pair or filename from Table 1. The first pair returns after the last pair displays. Values that cannot display on one line wrap to the next line.
Troubleshooting Guidelines Table 1: Parameter Values (continued) Name System Value Format IP address nnn.nnn.nnn.nnn Up to 15 ASCII characters: IPADD value. Subnet mask nnn.nnn.nnn.nnn Up to 15 ASCII characters: NETMASK value. Router nnn.nnn.nnn.nnn Up to 15 ASCII characters: the IP address of the router in use. File server nnn.nnn.nnn.nnn.nnnnn Up to 21 ASCII characters: IP address and port of last file server used successfully during initialization or “0.0.0.
Installation Error and Status Messages Installation Error and Status Messages The 1603SW-I IP Deskphones issue messages in the currently selected language, or if the telephone is logged off, in the language specified by the LANGSYS parameter value. If English is not the selected language, the telephone displays messages in English only when they are associated with local procedures, for example, MUTE V I E W. Most of the messages in Table 2 display only for about 30 seconds, and then the telephone resets.
Troubleshooting Guidelines Table 2: Possible Error and Status Messages During Installation of 1603SW-I IP Deskphones (continued) Message Cause/Resolution Finding router... CAUSE: The telephone is proceeding through boot-up. RESOLUTION: Allow the telephone to continue. CAUSE: The telephone is not a 1603SW-I IP Deskphone, and it does not supprt the SIP firmware. RESOLUTION: Replace the telephone with a 1603SW-I IP Deskphone. CAUSE: The telephone does not have sufficient room to store the downloaded file.
Installation Error and Status Messages Table 2: Possible Error and Status Messages During Installation of 1603SW-I IP Deskphones (continued) Message Cause/Resolution System busy CAUSE: Most likely, the number of IP endpoints on the call server is already at maximum, Less likely, network resource is unavailable. RESOLUTION: The telephone was attempting to access a network resource (DHCP server, HTTP server, or the call server) and was not successful.
Troubleshooting Guidelines Operational Errors and Status Messages Table 3 identifies some of the possible operational problems that might be encountered after successful 1603SW-I IP Deskphone installation. The user guide for a specific telephone model also contains troubleshooting for users having problems with specific IP telephone applications. Most of the problems reported by 1603SW-I IP Deskphone users are not likely to be problems with the telephone itself.
Operational Errors and Status Messages Table 3: Operational Error Conditions for 1603SW-I IP Deskphones (continued) Condition The telephone was working, but does not work now, Cause/Resolution AND no lights are lit on the telephone and the display is not lit. AND power to the telephone is fine, but there is no dial tone. The display might show “System Busy.” AND the telephone was recently moved.
Troubleshooting Guidelines Table 3: Operational Error Conditions for 1603SW-I IP Deskphones (continued) Condition Cause/Resolution The telephone works, but the audio quality is poor, specifically: the user hears echo when speaking on a handset. the user is on Speaker and hears no echo, but the far-end hears echo. the user experiences sudden silences such as gaps in speech, or static, clipped or garbled speech, etc.
Operational Errors and Status Messages Table 3: Operational Error Conditions for 1603SW-I IP Deskphones (continued) Condition The HTTP/HTTPS script file is ignored or not used by the telephone, Cause/Resolution AND the HTTP/ HTTPS server is a LINUX or UNIX system. AND telephone administration recently changed. Some settings in the settings file are being ignored while other settings are being used properly.
Troubleshooting Guidelines Table 3: Operational Error Conditions for 1603SW-I IP Deskphones (continued) Condition Cause/Resolution The user indicates an application or option is not available. CAUSE: The 46xxsettings script file is not pointed to accurately, or is not properly administered to allow the application.
Appendix A: Restart Scenarios Scenarios for the Restart Process The sequence of the restart process depends on the status of the boot and application files. This appendix explains the different scenarios possible. Note: Note: The file names used in this appendix are examples only. Your particular file names are likely to be different. Restart the Telephone Use the following procedure to restart the telephone. 1.
Restart Scenarios 3. Press the * key to terminate the procedure without restarting the telephone. Press the # key to restart the telephone. The remainder of the procedure depends on the status of the boot and application files: If this condition applies: See: Boot File Needs to be Upgraded Boot File Needs to be Upgraded on page 61.
Scenarios for the Restart Process Boot File Needs to be Upgraded The telephone automatically downloads an upgraded boot file if applicable. In this case, these messages appear: The telephone displays: Restarting... While the hardware is being initialized, the telephone displays: Initializing While either the application file if there is one or the boot code is uncompressed into RAM, the telephone displays: Loading: 5 secs replboot_v3.
Restart Scenarios Note: Note: The Ethernet speed indicated is the LAN interface speed for both the telephone and any attached PC, assuming the administrator has not disabled the latter interface through the PHY2STAT setting. The software determines whether sufficient IP address information was downloaded. In this scenario, it is discovered that sufficient information has not been downloaded.
Scenarios for the Restart Process application file to replace the boot code. The following message displays while the application file is downloaded into RAM: app_filename n KB received where n is the number of KBs downloaded. The following message displays while the application file is stored in flash memory: Saving to flash n%, x secs where n is the percentage of the file stored, and x is the number of elapsed seconds. This usually takes longer than the file download.
Restart Scenarios Latest Boot File Loaded/No Application File or Application File Needs to be Upgraded This procedure occurs with normal application file upgrades. The telephone displays: Restarting... The telephone detects and displays the speed of the Ethernet interface in Mbps, that is, 0, 10, or 100. The message No Ethernet displays until the software determines whether the interface is 10 Mbps or 100 Mbps.
Scenarios for the Restart Process Note: Note: The Ethernet speed indicated is the LAN interface speed for both the telephone and any attached PC. The software determines whether sufficient IP address information was downloaded. In this scenario, it is discovered that sufficient information has not been downloaded. The following message displays while the DHCP process is invoked: DHCP: 0 secs * to program The number of elapsed seconds is incremented once per second, until DHCP successfully completes.
Restart Scenarios application file to replace the boot code. The following message displays while the application file is downloaded into RAM: app_filename n KB received where n is the number of KBs downloaded. The following message displays while the application file is stored in flash memory: Saving to flash n%, x secs where n is the percentage of the file that was stored, and x is the number of elapsed seconds. This usually takes longer than the file’s download.
Scenarios for the Restart Process Note: Note: The Ethernet speed indicated is the LAN interface speed for both the telephone and any attached PC. The software determines whether sufficient IP address information was downloaded. In this scenario, it is discovered that sufficient information has not been downloaded. The following message displays while the DHCP process is invoked: DHCP: 0 secs * to program The number of elapsed seconds is incremented once per second, until DHCP successfully completes.
Restart Scenarios 68 Avaya 1603SW-I SIP Deskphones Installation and Maintenance Guide
Appendix B: Glossary of Terms Terms Used in This Guide 802.1P 802.1Q 802.1X ARP CLAN DHCP DiffServ DNS Gatekeeper H.323 HTTP HTTPS IETF LAN MAC QoS Unnamed Registration TLS VLAN VoIP 802.1Q defines a layer 2 frame structure that supports VLAN identification and a QoS mechanism usually referred to as 802.1P. Authentication method for a protocol requiring a network device to authenticate with a back-end Authentication Server before gaining network access.
Glossary of Terms 70 Avaya 1603SW-I SIP Deskphones Installation and Maintenance Guide
Appendix C: Related Documentation IETF Documents IETF documents provide standards relevant to IP Telephony and are available for free from the IETF Web site: http://www.ietf.org/rfc.html. ITU Documents Access the ITU Web site for more information about ITU guidelines and documents, available for a fee from the ITU Web site: http://www.itu.int.
Related Documentation 72 Avaya 1603SW-I SIP Deskphones Installation and Maintenance Guide
Index Index Numerical 1603SW-I SIP Deskphone Assembling the . . . . . . . . . . Installation . . . . . . . . . . . . Maintenance . . . . . . . . . . . Models . . . . . . . . . . . . . . Powering the . . . . . . . . . . . Restart . . . . . . . . . . . . . . 802.1X Operational Mode, Setting the . E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 . 9 43 10 14 40 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Parameter Values . . . . . . . . . . . . . . . . 49 Power Interruption . . . . . . . . . . . . . . . . 48 VIEW Administrative Option . . . . . . . . . . . 48 O Operational Errors and Status Messages . . . . . . 54 Other Documentation . . . . . . . . . . . . . . . . 7 P Parameter Values . . . . . . . . . . . . . . Power Interruption . . . . . . . . . . . . . . Powering the 1603SW-I SIP Deskphone. . . . Pre-Installation Checklist . . . . . . . . . . .
