Application Note

ManualsBrandsAvaya ManualsTelephoneAvaya 4600 Series IP Telephones

Avaya Solution & Interoperability Test Lab

Application Notes for Extreme Networks Aspen 8810 PoE

Module with Avaya 4600 Series IP Telephones and Avaya

Wireless Access Points - Issue 1.0

Abstract

These Application Notes describe how to configure the Power over Ethernet module of the

Extreme Networks Aspen 8810 to provide inline power for Avaya 4600 Series IP telephones

and Avaya Wireless Access Points. The various Avaya powering arrangements are shown and

the administration commands for displaying and controlling the powering status of the switch

ports are demonstrated. All test cases completed successfully. Information in these Application

Notes has been obtained through compliance testing and additional technical discussions.

Testing was conducted via the DeveloperConnection Program at the Avaya Solution and

Interoperability Test Lab.

JZ; Reviewed:

SPOC 2/14/2005

Solution & Interoperability Test Lab Application Notes

1 of 11

Aspen-PoE.doc

Summary of content (11 pages)

PAGE 1
Avaya Solution & Interoperability Test Lab Application Notes for Extreme Networks Aspen 8810 PoE Module with Avaya 4600 Series IP Telephones and Avaya Wireless Access Points - Issue 1.0 Abstract These Application Notes describe how to configure the Power over Ethernet module of the Extreme Networks Aspen 8810 to provide inline power for Avaya 4600 Series IP telephones and Avaya Wireless Access Points.
PAGE 2
1. Introduction Power over Ethernet (PoE) is a feature offered on Ethernet switches. It allows the switch to supply power to a network device within the same cable that carries the Ethernet signaling. This simplifies network installation and powering design, removing the need for a separate power supply for a network device. IEEE 802.3af defines a standard protocol to be used by power sourcing equipment (PSE) and powered devices (PD). The PoE module of the Extreme Networks Aspen 8810 is IEEE 802.
PAGE 3
• For wireless LAN access points, successful registration for an Avaya IP Softphone with an Avaya Communication Manager and completion of a test call. Avaya H.323/SIP VoIP Infrastructure Avaya 4602SW SIP Telephone Avaya 4601 IP Telephone Extreme Networks Aspen 8810 EU24 Avaya 4620/4620SW IP Telephone with and without EU24 Avaya 4602 /4602SW IP Telephone Avaya 4610SW IP Telephone Avaya Gen-2 4606 IP Telephone Avaya Gen-2 4612/4624 IP Telephone Wireless Laptop (Avaya 802.
PAGE 4
2.
PAGE 5
Table 3 shows the detected class, maximum allowed power, and measured power by the Extreme Networks Aspen 8810 Switch for the Avaya IP telephones and Wireless Access Points. The power was measured when the powered devices were idle. Avaya IP Telephone Class 4601 4602 4602 SW 4610 SW 4620 4620 with EU24 4620 SW 4620 SW with EU24 4630 SW Gen-2 4606 Gen-2 4612 Gen-2 4624 4602SW SIP Avaya AP-4/5/6 2 1 2 2 3 3 3 3 3 0 0 0 2 0 Max Allowed Power (Watts) 7.0 4.0 7.0 7.0 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.
PAGE 6
The Aspen supports six power supply units. Use the command show power budget to view the distribution of power and available power on the switch. As shown in the following table, there are three power supply units and the total power available is 1968.00 Watts. The PoE module is in Slot 2. Aspen.38 # show power budget PS State Watts 48V 12V --------------------------------------------------------------------------1 Powered On 656.00 608.00 48.00 2 Powered On 656.00 608.00 48.00 3 Powered On 656.00 608.
PAGE 7
will send an alarm. The Usage Threshold can be configured by the command configure inlinepower usage-threshold , which applies to each PoE slot on the switch. Aspen.45 # enable inline-power Aspen.46 # enable inline-power slot 2 Aspen.47 # configure inline-power budget 480 slot 2 Aspen.
PAGE 8
Use the command show inline-power stats slot to show the inline power statistics of the specified slot. Aspen.60 # show inline-power stats slot 2 Inline-Power Slot Statistics Slot: 2 Firmware status Firmware revision : Operational : 292b1 Total Total Total Total : : : : ports ports ports ports powered awaiting power faulted disabled 3 45 0 0 Use the command show inline-power stats port to show status for the specified port(s). Aspen.
PAGE 9
Aspen.68 # show inline-power info detail ports 2:1-3 Port 2:1 Configured Admin State: Inline Power State : MIB Detect Status : Label : Operator Limit : PD Class : Max Allowed Power : Measured Power : Line Voltage : Current : Fault Status : Detailed Status : Priority : enabled delivering delivering 15400 milliwatts class2 7.0 W 3.200 W 48.
PAGE 10
4. Interoperability Compliance Testing This Interoperability Compliance Test included PoE testing between the Extreme Networks Aspen 8810 and the Avaya 4600 Series IP telephones and Avaya Wireless Access Points. 4.1. General Test Approach PoE test cases based on Figure 1 were performed manually. PoE worked as expected for the test cases, including plugging/unplugging the Avaya PDs, enabling/disabling PoE on the switch, and resetting the switch. 4.2. Test Results All test cases passed.
PAGE 11
©2005 Avaya Inc. All Rights Reserved. Avaya and the Avaya Logo are trademarks of Avaya Inc. All trademarks identified by ® and ™ are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners. The information provided in these Application Notes is subject to change without notice.