Installing a V.34 Console Modem Module in a BayStack ARN Router Part No.
4401 Great America Parkway Santa Clara, CA 95054 8 Federal Street Billerica, MA 01821 Copyright © 1998 Bay Networks, Inc. All rights reserved. Printed in the USA. May 1998. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty.
Japan/Nippon Requirements Only Voluntary Control Council for Interference (VCCI) Statement Voluntary Control Council for Interference (VCCI) Statement This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is located on the “FCC Rules Part 68” label located on the bracket of the module, or on the back of the unit. Canada CS-03 -- Règles et règlements Avis: L'étiquette d'Industrie Canada identifie le matériel homologué.
• When you request V.34 Service, you must provide the telephone company with -- The required Universal Service Order Code (USOC) jack: RJ11C -- The make, model number, Ringer Equivalence Number (REN), and FCC Registration number of the unit The REN helps you determine the number of devices you can connect to your telephone line and still have all of those devices ring when your number is called. In most, but not all, areas, the sum of the RENs of all devices should not exceed 5.0.
Bay Networks, Inc. Software License Agreement NOTICE: Please carefully read this license agreement before copying or using the accompanying software or installing the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement). BY COPYING OR USING THE SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS UNDER WHICH BAY NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE.
its own data and information and for maintaining adequate procedures apart from the Software to reconstruct lost or altered files, data, or programs. 4. Limitation of liability.
Contents About This Guide Before You Begin .............................................................................................................xiii Conventions .....................................................................................................................xiii Bay Networks Technical Publications ..............................................................................xiii Bay Networks Customer Service .......................................................................
Figures Figure 1. ARN Power Switch (Off) and Power Cables ................................................ 2 Figure 2. Loosening the Captive Screws on the Enclosure ........................................ 2 Figure 3. Removing the ARN Enclosure .................................................................... 3 Figure 4. Removing the Screws from an Installed Module ......................................... 4 Figure 5. Removing the Filler Plate ...................................................
About This Guide Before You Begin Make sure that you are running the latest version of Bay Networks ® Site Manager and router software. The Advanced Remote Node (ARN™) router requires BayRS™ Version 11.00 Rev. 4n or later. Conventions italic text Indicates variable values in command syntax descriptions, new terms, file and directory names, and book titles. quotation marks (“ ”) Indicate the title of a chapter or section within a book.
Installing a V.34 Console Modem Module in a BayStack ARN Router Bay Networks Customer Service You can purchase a support contract from your Bay Networks distributor or authorized reseller, or directly from Bay Networks Services.
About This Guide Bay Networks Educational Services Through Bay Networks Educational Services, you can attend classes and purchase CDs, videos, and computer-based training programs about Bay Networks products. Training programs can take place at your site or at a Bay Networks location.
Installing the V.34 Console Modem This document describes how to install a V.34 Console Modem module in a BayStack ARN router. Topic Page Opening the ARN -1 Removing an Installed Module -4 Installing a Console Modem Module -5 Closing the ARN -8 Connecting the Console Interface -9 Before installing the module, examine the contents of your V.34 Console Modem module upgrade kit. If any parts appear damaged, call the Bay Networks Technical Solutions Center immediately.
Installing a V.34 Console Modem Module in a BayStack ARN Router Power switch (off) UL Redundant Power UL 100-240~ 1.2A 50-60Hz To power outlet To redundant power supply ARN0017A Figure 1. ARN Power Switch (Off) and Power Cables 2. Remove all console cables from the back panel. 3. Remove all network cables from the front panel. 4. Loosen the two captive screws on the ARN back panel that secure the top enclosure to the ARN component tray (Figure 2). Be sure to loosen the screws all the way.
Installing the V.34 Console Modem 5. Place the ARN tray on a table or other work surface. 6. Holding the ARN front panel so that it does not move, slide the ARN enclosure away from the front panel and component tray (Figure 3). RLSD3 RLSD4 Tx RLSD5 Rx D ISDN BRI withNT1 1 DD B1 Cl k B2 Run Boot Tx Fail Pwr RPS Fan Base Adapter1 Adapter2 Expansion BayStac Advanced Remote Node DCM PCMCIA Rx 2 Figure 3. 7.
Installing a V.34 Console Modem Module in a BayStack ARN Router Removing an Installed Module To remove an existing V.34 Console Modem module from the ARN base module: 1. Locate the installed module and remove the screws that secure it to the base module (Figure 4). ARN0046B Figure 4. 4 Removing the Screws from an Installed Module 2. Grasping the edges of the module near the base module connector, pull straight up and lift the module out of the connector socket. 3.
Installing the V.34 Console Modem Installing a Console Modem Module To install a V.34 Console Modem module: 1. Remove and set aside the two screws that secure the filler plate for the back panel V.34 Console Modem slot (Figure 5). 2. Remove the filler plate (Figure 5). ARN0079A Figure 5. Removing the Filler Plate 3. Attach two mounting screw standoffs at either side of the base module’s V.34 modem connector (Figure 6). The standoff mounts came with the V.34 Console Modem upgrade kit.
Installing a V.34 Console Modem Module in a BayStack ARN Router Screw mount V.34 Modem Module connector ARN0044B Figure 6. Installing Screw Mounts 4. 6 Hold the module by its edges, with the base module connector facing down (Figure 7).
Installing the V.34 Console Modem ARN0045A Figure 7. Positioning the Module 5. Place the console modem module into the base module connector socket and press down to seat the module firmly in the socket. 6. Secure the module using the screws supplied in your upgrade kit (Figure 8). ARN0046A Figure 8.
Installing a V.34 Console Modem Module in a BayStack ARN Router Closing the ARN To replace the ARN enclosure: 1. Remove the antistatic wrist strap. 2. Facing the back panel, align the enclosure top around the base module component tray and slide the enclosure in until it meets the front panel. If you meet resistance, lift up slightly on the enclosure, and center the component tray between the enclosure edges. 3. Secure the two captive screws that hold the cover to the component tray (Figure 9).
Installing the V.34 Console Modem Connecting the Console Interface Before reconnecting the ARN to the network, connect an RJ-11 modem cable to the new V.34 modem interface (Figure 10). Modem Console TX RLSD RX DTR Modem ARN0037A Figure 10. V.34 Console Modem Connector For cables available from Bay Networks, refer to the BayRS Cable Guide. To configure and use the V.34 modem as a router console, see Installing and Operating BayStack ARN Routers or the Configuring BayStack Remote Access guide.
