User manual

Specifications
ADPRO FastTrace, Issue 5 3 - 3
3.1 ADPRO FastTrace Version 1.02
An ADPRO FastTrace system consists of one or more Multi-Site Video Security System at a remote site and a PC
running the ADPRO Video Central Lite software at a monitoring site. Connection is via a TCP/IP based Ethernet
network or dial-up or leased telephone lines.
Function Description
Video inputs Model 5005 = 5 BNC video channel inputs, Model 5010 = 10 video inputs, Model 5020 = 20 video
inputs,
1 volt p/p video input, 75 ohm or high impedence, selectable via menu.
Colour / Monochrome Operation Colour or monochrome. Default operation is for colour. Individual channels can be selected as
monochrome (B&W).
Video output 1 BNC composite video output designed to drive a 75-ohm load.
Video standard Either PAL or NTSC (switch selectable).
Colourburst lock range PAL 4.433619MHz ± 230Hz
NTSC 3.579545MHZ ± 179Hz
Recording image resolution 2CIF, PAL: 704 x 288 pixels
2CIF, NTSC: 704 x 240 pixels
CIF, PAL: 352 x 288 pixels
CIF, NTSC: 352 x 240 pixels
Grey Scale Resolution 256.
Video Compression Engine (VCE) Maximum of 4x VCE modules per chassis.
Image compression is via customised H.263 compression algorithm resulting in an average of
3KB per images at CIF resolution picture quality 6 and 6KB per image at 2CIF resolution picture
quality 7.
Recording rate, aggregate across all
channels at CIF resolution.
With 1x VCE: PAL: 25 images per second, NTSC: 30 images per second.
With 2x VCE: PAL: 50 images per second, NTSC: 60 images per second.
With 3x VCE: PAL: 75 images per second, NTSC: 90 images per second.
With 4x VCE: PAL: 100 images per second, NTSC: 120 images per second.
Note that for 2CIF resolution, these recording rates are halved.
Hard Disk Drive (HDD) capacity Maximum 4x HDD, IDE interface, internally mounted.
Video Display modes at video output Full screen spot or sequence monitoring.
Image transmission rate Typical transmission rates (subject to amount of scene activity):
Ethernet: 25 images per second
ISDN: 128Kbps = 12.5 images per second
PSTN 33.6Kbps = 3 images per second
Alarm inputs Model 5005 and Model 5010: 20 alarm contact sensing or logic level inputs.
Model 5020: 30 alarm contact sensing or logic level inputs.
Programmable to trigger an alarm on contact opening or closure.
All inputs have impedence >1K ohm and transient protection >20KV.
Single End-of-Line (SEOL) or Dual End-of-Line (DEOL) tamper detection on each input.
Screw terminal connectors.
Voltage input less than 0.8 V = logic low, 7 mA (maximum).
Voltage input between 3.5V and 5.0V = logic high.
Minimum alarm contact duration = 0.5 seconds
Activity Detect Zones The maximum activity detection area is defined by the number of available detection zones:
396 zones (22 wide x 18 high) using CIF PAL resolution (352 x 288 pixels)
330 zones (22 wide x 15 high) using CIF NTSC resolution (352 x 240 pixels)
A detection zone represents a screen area of 16 x 16 pixels.
Control outputs Model 5005 and Model 5010: 10 open collector outputs.
Model 5020: 20 open collector outputs.
Screw terminal connectors.
12Vdc (maximum), 100mA (maximum)
‘On state’ output voltage less than 1.1V @ 100mA.
General Alarm Relay output Form C, single pole changeover. Relay contact ratings: 1.0 amp, 32 volts.