User manual

Specifications
3 - 4 ADPRO FastTrace, Issue 5
Function Description
Network Port 1x Ethernet 10BaseT / 100BaseT compatible supporting TCP/IP. RJ-45 connector.
Serial Communication Interface 2x V.24 asynchronous interfaces - 8 data bits, 1 stop bit, no parity, programmable data rate steps
from 9600 to 230400 bps. 1x 9 pin male D, 1x 25-pin male D. Configured as a DTE device.
Supports Hayes (AT) compatible ISDN and PSTN modems in dial or leased line configuration.
Support for Multilink PPP or V.120 data protocol over ISDN.
GP Serial Ports 2x General Purpose (GP) serial RS-232 data ports for POS/ATM connection. 9 pin male D
connectors. Configured as a DTE device. Maximum baud rate of 38,400 bps.
Programmable number of data bits (6, 7 or 8), stop bits (1 or 2), parity (odd, even, none),).
Data (Transparent) Interface Bi-directional (transparent) RS-232 serial data link between the Transmitter and Receiver.
Configured as a DTE device.
Programmable baud rate from 1200, 2400, 4800, 9600, 19200, 38400, and 57600 bps.
Programmable number of data bits (7 or 8), stop bits (1 or 2), parity (odd, even, none), flow control
via handshaking (or Off).
9 pin male D connector.
I/O Interface 1x ‘Mode Select’ input pin. Programmable control of mode numbers assigned to pin state.
1x ‘Access/Secure’ input for 3rd-party control of operational state. Open=Secure,
Ground=Access.
Available via 15-pin male D connector.
Audio Switch Interface Audio In/Out to VM22A or third party Audio Switcher.
Bi-directional audio sent simultaneously with the video (full duplex).
Bandwidth: 300 Hz to 3.3 kHz.
Input impedance: >6Kohms. Input level: 10mV to 400mV RMS (nom)
Output impedance: >6K ohm. Output level: 315mV (nom)
Serial Output for Channel Number sequencing.
Open drain outputs (binary coded hex) indicating the currently selected channel.
32V maximum, 100 mA maximum, output impedence <0.5 ohm
Refer to VM22A Audio Switcher manual for details of serial protocol.
Audio Connector Direct connection via 9-pin screw connector.
Microphone: Differential impedance >3 Kohm
Single-ended impedance >6 Kohm
Nominal signal level is 100uV to 10mV rms.
Speaker: 1 Watt (max) into 8 ohm load.
Line In: Unbalanced input impedance >6 Kohm
Nominal signal level is 10mV to 400mV rms.
Line Out: Balanced output impedance = 600 ohm
Nominal level is 315mV rms.
Power requirements AC Operation 115 - 230 VAC, 47 - 63 Hz, 100 Watts (max).
Construction & dimensions Standard 19” rackmount, 3U high subrack to DIN4194.
482mm (19”) W x 132mm (5.25”) H x 280mm (11”) D
Weight (fully configured condition) 11 Kg (22lb)
Temperature range Operating range 0 degC to 40 degC (32 degF to 104 degF)
Humidity less than 90% non-condensing.
EMC Compliance EMC Emission:
EN55022:1998 (CISPR 22:1997) / AS/NZS 3548:1995 + A1, A2 Class A Conducted and radiated
emissions
FCC Part 15 Class A Conducted and radiated emissions
EN61000-3-2:1995 Mains harmonic current emissions
EN61000-3-3:1995 Voltage fluctuations and flicker
EMC Immunity:
EN50130-4:1995 +A1 Alarm Systems Immunity
EMC Directive 89/336/EEC and carries CE marking
Safety Compliance EN 60950:1992 +A1, A2, A3, A4, + A11
IEC60950: 1991 +A1, A2, A3 & A4
Low Voltage Directive 73/23/EEC and carries CE marking
UL Listed to US and Canadian Safety Standards
UL File Number E219750