VENDOMA-MPG DVR (Digital Video Recorder) Hardware Installation Guide Version 1.00.00 © 2004 Aventura Technologies, Inc.
VENDOMA DVR t INDEX 1. Features 4 2. Installation Notes 6 3. Products and Components 7 4. Install Capture Board 8 4-1. Vendoma MPG 12004 Board 8 4-2.
VENDOMA DVR t Preface This guide book describes the individual hardware components and how to install them. For a description of the software and how to install it, please refer to the Installation and User Guide provided with your unit. This guide is for the following Aventura Technologies products: Vendoma MPG 12004, 24008, and 48016 capture boards. Board shapes and item names may be slightly different than those in this manual. We are looking forward to hearing your comments about our DVR.
VENDOMA DVR t 1.
VENDOMA DVR t Motion Detection and Sensor Trigger You can set the DVR to record only when movements are detected, which saves storage space. Scheduled recording You can specify a recording schedule. Data Backup and Auto Backup Backed up data can be transferred to different media, such as DAT, CD, or DVD. You can also back up the data from a specific camera and view the date and time stamp on the footage. Like the scheduled recording, the data backup program can also be scheduled.
VENDOMA DVR t 2. Installation Notes We recommend the following for ideal performance: Intel chip motherboards Intel Pentium 4 or equivalent (Nothing lower than a 2.0 GHz Celeron) 256 MB or more of RAM 80 GB or more hard disk space If you try to use a 160 GB hard drive or higher, your operating system should be updated with the latest service pack.
VENDOMA DVR t 3. Products and Components VENDOMA-MPG 12004 VENDOMA-MPG 24008 (120 Frames per second, 4 Channels) (240 Frames per second, 8 Channels) MPG 12004 Accessory MPG 24008 Accessory Type A MPG 24008 Accessory Type B MPG 48016 Accessory Type A MPG 48016 Accessory Type B The boards pictured above and their accessories may be subject to change by hardware upgrade.
VENDOMA DVR t 4. Install Capture Board 4-1.
VENDOMA DVR t 1 Connect audio input cable 2 Connect video input cable 3 Connect TV-OUT cable 4 Connect sensor relay cable 5 Connect Watchdog cable Assembly View Note: 1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next to the Watchdog on the DVR card. 2.
VENDOMA DVR t 4-2.
VENDOMA DVR t 1 Connect audio input cable 2 Connect video input cable 3 Connect TV-OUT cable 4 Connect sensor relay cable 5 Connect Watchdog cable Assembly View Note: 1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next to the Watchdog on the DVR card. 2.
VENDOMA DVR t 4-3.
VENDOMA DVR t 1 Connect Audio Input cable 2 Connect BNC cable 3 Connect Back panel cable 4 Connect Sensor Relay cable 5 Connect Watch dog cable Assembly View Note: 1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next to the Watchdog on the DVR card. 2.
VENDOMA DVR t 4-4.
VENDOMA DVR t 1 Connect Video cable 2 Connect Audio cable (MPG 24008-1 & MPG 24008-2) (MPG 24008-1 & MPG 24008-2) 3 Connect TV-OUT cable 4 Insert Sensor Relay (MPG 24008-1 Only) (MPG 24008-1 & MPG 24008-2) 5 Connect Watch dog cable 6 MPG 24008-1 & MPG 24008-2 (MPG 24008-1 Only) Hook up TV-OUT Loop 15
VENDOMA DVR t Assembly View 1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next to the Watchdog on the DVR card. 2. If the Watchdog cable and/or the Reset switch are connected incorrectly, the system will not reboot and you may not have video. Try reconnecting the pins to restore the video.
VENDOMA DVR t 4-5.
VENDOMA DVR t 1 Connect Audio cable 2 Connect BNC cable ( MPG 24008-1 & MPG 24008-2) ( MPG 24008-1 & MPG 24008-2) 3 Connect BNC cable 4 connect Back panel cable ( MPG 24008-1 & MPG 24008-2) 5 Insert Sensor Relay 6 Connect Watch dog cable ( MPG 24008-1 & MPG 24008-2) ( MPG 24008-1 Only) 18
VENDOMA DVR t 7 MPG 24008-1 & MPG 24008-2 Assembly View Hook up TV-OUT Loop 1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next to the Watchdog on the DVR card. 2. If the Watchdog cable and/or the Reset switch are connected incorrectly, the system will not reboot and you may not have video. Try reconnecting the pins to restore the video.
VENDOMA DVR t 5. Pin numbers 5-1.
VENDOMA DVR t 5-2.
VENDOMA DVR t Sensor & Relay(digital I/O) Pin name Pin number Sensor Input 0-7 1-8 Input Common 0-1 17, 18 Relay(Digital) Output 0-3 19-22 Output Common 0-1 23, 24 Watchdog Pin name Pin number Signal Ground 1, 3 Reset Signal 2, 4 Pin Arrangements of MPG 48016 are as follows: Video I/O (Camera Connector) MPG 24008-1 MPG 24008-2 Group name Camera number Group name Camera number A Camera 1-4 A Camera 9-12 B Camera 5-8 B Camera 13-16 22
VENDOMA DVR t 5-3.
VENDOMA DVR t Video Input 12345678G Audio Input GG4321 Sensor & Relay (Digital I/O) 24
VENDOMA DVR t 6. RS232 TO RS422/485 Converter This is the converter for controlling the Pan/Tilt/Zoom camera. 1. Connect the cable to computer serial Port. 2. You can select one of three Power connectors: - 1 : Power from Capture Board (+5V) 1 - 2 : Power from System Power Supply 2 - 3 : Power from System Power Supply 3 3. Connect data line from camera to this port. 4.
VENDOMA DVR t RS-422/485 Pin number RS-422/485 Connector 1 2 3 4 5 6 Pin name Pin number - TxData 2 + TxData 3 - RxData 4 + RxData 5 Signal 1,5 26
VENDOMA DVR t 7. Vendoma System Assembly 7-1. Front Views 1. Cooling fan This fan removes the excessive heat generated in the system and enhances the system’s stability. 2. HDD LED When your hard disk drives (HDDs) are running, this light either blinks or remains steady). 3. Power LED This light is on when your system is powered on. 4. 3 ½” Floppy Drive (Optional) 5. CD-ROM or DVD-ROM 6. Reset switch 7. Power switch Push this button to power on the DVR.
VENDOMA DVR t 7-2. Rear View 1. AC Power Cooling fan – This fan also removes the excessive heat generated in the system and enhances the system’s stability 2. Sensor & Relay I/O connectors – This is the sensor and relay-out port for systems that have a BNC back panel installed. Systems that have a pigtail type connector (also called a Dongle) installed do not need this type of sensor. 3. Camera input connectors – This is the camera input for systems that have a BNC back panel installed.
VENDOMA DVR t 14. Video output connector – This is for monitor (VGA) connector. 15. Pan/Tilt connector – If your system was equipped for Pan/Tilt/Zoom controls, then you have one of these connectors 16. LAN connector Please note that all DVRs must be connected an Uninterruptible Power Supply (a UPS) with line conditioning. At least a 550VA (1530 minutes) or more is recommended.
VENDOMA DVR t 6: Pan/Tilt/Zoom Camera Connection Guide RS232/485 Converter This converter is for the control of Pan/Tilt which are supported in the RS232/485 Port . 1. Connect DB9 pin cable between the serial Port in the motherboard board and RS232 port in this converter. RS-422/485 Connector This is what the RS 232-485 Connections look like, Pin name Pin number you need to connect the Controller Cable from the Ground 1 P/T/Z to this connection as shown above (RX+ and - TxData 2 RX-).
VENDOMA DVR t 2. For power connection, you may utilize one of the following 3 sources. - 1 : Connect the power cable from power unit to socket No.2 (+5V) - 2 : Connect the power cable from power unit to socket No.3 - 3 : Connect power cable from capture board to socket No.1(Option) 3. Set the jumper as follow, on RS-422 Pan/Tilt settings Set the jumper as follows, on RS-485 Pan/Tilt settings. 4. Connect the cable from RS485/422 port to PTZ driver as displayed in the following figure. 5.
