AV Connectivity, Distribution And Beyond... VIDEO WALLS VIDEO PROCESSORS VIDEO MATRIX SWITCHES EXTENDERS SPLITTERS WIRELESS CABLES & ACCESSORIES HDBaseT HDMI Wall Plate Receiver IR/RS232/POE 100M Model #: HBT-C6POEWP-R © 2013 Avenview Inc. All rights reserved. The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products.
Product Application & Market Sectors Corporate House Of Worship Military Residential Education Industrial Medical Aviation www.avenview.
TABLE OF CONTENTS 1. GETTING STARTED...........................................................................................................................1 1.1 IMPORTANT SAFEGUARDS...............................................................................................................1 1.2 SAFETY INSTRUCTIONS...................................................................................................................1 1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)..........
1. GETTING STARTED SECTION 1: GETTING STARTED 1.1 IMPORTANT SAFEGUARDS Please read all of these instructions carefully before you use the device. Save this manual for future reference. What the warranty does not cover •• Any product, on which the serial number has been defaced, modified or removed.
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. Warning symbols Description ONLY USE THE PROVIDED POWER CABLE OR POWER ADAPTER SUPPLIED. DO NOT TAMPER WITH THE ELECTRICAL PARTS.
2. INTRODUCTION The Avenview HBT-C6POEWP-R HDBaseT HDMI wall plate receiver was developed to simplify the install and also create a clean seamless look with the decor. Accepts the transmitted HDMI signal over Single CAT5e/6 from the TX of uncompressed audio/video, data control through the built-in RS-232 and IR ports. No need to power this unit because the TX wall plate supplies Power on Ethernet (PoE) over the CAT5/6 to this Receiver wall plate extending all signals up to 100m to the display screen.
2.1 PACKAGE CONTENTS Before you start the installation of the HDMI Extender, please check the package contents. 1 HDM-C6VWIP-SET X 1 X1 IR EXTENDER IR BLASTER 3.5 TO RS-232 FEMALE CABLE 2 3.5 TO RS-232 MALE CABLE USER’S MANUAL www.avenview.
2.2 BEFORE INSTALLATION •• Put the product in a level and stable location. If the product falls, it may cause damage or malfunction to components within the casing. •• Do not place the product in temperatures under 0˚C or over 50˚C. High humidity may also cause the unit to malfunction. •• Use the DC power adapter with correct specifications supplied with the unit. If the improper power supply is used, this may result in malfunction of the unit and may cause fire.
2.3 APPLICATION DIAGRAM www.avenview.
2.4 PANEL DESCRIPTION 2.4.1 INPUT PANEL (HBT-C6POEWP-S) Front Panel 5 6 1 2 3 4 1. RS-232 OUT: Connect using the 3.5mm jack to RS232 Cable to devices that receives RS232 Commands 2. IR 1 IN: Connect the IR Receiver cable included to receive IR Signal. 3. IR 2 OUT: Connect the IR blaster cable included to transmit IR Signal. 4. HDMI OUT: Connect with HDMI male cable to display audio/video signal to screen 5. Power LED: Green LED will illuminate when the supplied power supply is attached. 6.
3. INSTALLATION (HBT-C6POEWP-S) To setup Avenview HBT-C6POEWP-R please follow these steps for connecting to a device: 1. Power off sources such as using Laptop/PC DVD player at Podium or where installed. 2. Connect HDMI video Source to the HDMI INPUT on the compatible TX- up to with Full HD, 3D and 4k x 2k support 3. Connect CAT 5/6 OUT to a compatible HBT-C6POEWP-R (Rx) CAT 5/6 IN and HDMI cable to HDMI Displays 4. Plug in 24V/1.
-4. IR CABLE DEFINITION --- IR Sockets IR BLASTER: plug in the IR blaster to the HBT-C6POE-R to emit all IR command signals received from the IR Extender plugged into the Rx (Monitor Side) to control the devices corresponding to the IR signals. Example: Set Top Box or DVD player (The Source). IR EXTENDER: plug in the IR Extender into the (RX) Receiver (Monitor Side) to receive all IR command signals from the IR remote controls of the corresponding source.
5. GENERAL TROUBLESHOOTING PROBLEM POSSIBLE SOLUTION •• Check if connection to the source and the display are correct. •• Ensure that display device supports 480p, 720p and 1080p 4K@30 resolution •• Terminated to 568B standard with Shielded Ends Recommended •• High Quality CAT5/6/7 Cable helps signal transmission NO IMAGE •• Please use the supplied power supply-DC 24V 2.
SECTION 7: SPECIFICATIONS 6.
NOTICE 1. All HDMI over UTP transmission distances are measured using Belden CAT6A (625MHz), 4-Pair, U/UTP-Unshielded, Riser-CMR, Premise Horizontal Cable, 23 AWG Solid Bare Copper Conductors, Polyolefin Insulation, Patented Double-H spline, Ripcord, PVC Jacket using Quantum 980 signal HDMI Video Generator Module Video Pattern Testing. 2. The transmission length is largely affected by the type of category cables, also the type of HDMI sources, and the type of HDMI display.
AV Connectivity, Distribution And Beyond... TECHNICAL SUPPORT USA Head Office Avenview Corp. 275 Woodward Avenue Kenmore, NY 14217 Phone: 1.716.218.4100 Fax: 1.866.387.8764 Email: info@avenview.com Canada Sales Avenview 151 Esna Park Drive, Units 11 & 12 Markham, ON, L3R 3B1 Phone: 1.905.907.0525 Fax: 1.866.387.8764 Email: info@avenview.com Avenview Europe Avenview Europe Demkaweg 11 3555 HW Utrecht Netherlands Phone: +31(0)85.2100.613 Email: info@avenview.eu Avenview Hong Kong Unit 8, 6/F.