Specifications

ManualsBrandsAvenview ManualsComputer equipmentSW-HDM3D-C6-4X4E

4x4 HDMI Matrix Switch over Single CAT5/6

With Deep Color & 3D Support

The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties

with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product

descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this

publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express

or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or

infringement of any intellectual property right. Reproduction of this manual, or parts thereof, in any form, without the express written permission of

Avenview Inc. is strictly prohibited.

Model #: SW-HDM3D-C6-4X4E

Model #: HDM3D-C6SW-R

Summary of content (27 pages)

PAGE 1
4x4 HDMI Matrix Switch over Single CAT5/6 With Deep Color & 3D Support Model #: SW-HDM3D-C6-4X4E Model #: HDM3D-C6SW-R © 2012 Avenview Inc. All rights reserved. The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice.
PAGE 2
TABLE OF CONTENTS SECTION 1: GETTING STARTED ................................................................................................ 3 1.1 IMPORTANT SAFEGUARDS ................................................................................................ 3 1.2 SAFETY INSTRUCTIONS ..................................................................................................... 3 1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) .......... 4 SECTION 2: SWHDM3D-C6-4X4E .......
PAGE 3
SECTION 1: GETTING STARTED 1.1 IMPORTANT SAFEGUARDS PLEASE READ ALL OF THESE INSTRUCTIONS CAREFULLY BEFORE YOU USE THE DEVICE. SAVE THIS MANUAL FOR FUTURE REFERENCE. WHAT THE WARRANTY DOES NOT COVER            1.2 Any product, on which the serial number has been defaced, modified or removed.
PAGE 4
Keep the module away from liquids. Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately. Have the module checked by a qualified service engineer before using it again. Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning. 1.
PAGE 5
SECTION 2: SWHDM3D-C6-4X4E 2.1 INTRODUCTION The Avenview SW-HDM3D-C6-4x4E, HDMI Matrix with IR, Full 3D Support and now Ethernet over Single CAT6 provides the most flexible and cost effective solution in the market to route high definition video sources plus multi-channel (up to 7.1 channel) digital audio from any of the eight HDMI sources to the remote displays at the same time.
PAGE 6
2.2 PACKAGE CONTENTS Before you start the installation of the MARTIX SWITCHER please check the package contents. - - 2.3 SW-HDM3D-C6-4x4E HDM3D-C5SW-R IR Blaster IR Receiver IR Remote Control Rack mounting Ear Power Cable User’s Manual Software CD x1 x4 x1 x5 x1 x2 x1 x1 x1 BEFORE INSTALLATION     Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.
PAGE 7
2.4 PANEL DESCRIPTION SW-HDM3D-C6-4X4E- FRONT PANEL 1. SOURCE STATUS : Input source indicator LED 3. OUTPUT PUSH BUTTON & 7-SEGMENT LED: Front panel push buttons used to select the number of display channel & LED display for output ports 2. IR SENSOR: IR sensor for receiving the IR commands from IR remote 4. INPUT PUSH BUTTON & 7-SEGMENT LED: Front panel push buttons used to select the number of input source & LED display for input channels SW-HDM3D-C5-4x4E REAR PANEL 5.
PAGE 8
HDM3D-C6SW-R FRONT & BACK 1. SIGNAL LEVEL: Adjust the 8-level equalization 2. HDMI OUTPUT: Connect to HDTV with a HDMI cable 3. IR RECEIVER: Plug in IR receiver 4. IR BLASTER: Plug in IR blaster 5. +5V DC: 5V DC power jack 6. HDMI SIGNAL IN: Plug in a Cat.X cable SIGNAL LEVEL (MAX (0 – 7) MIN) Adjust the 8-level equalization control to the received HDMI signals.
PAGE 9
2.5 IR CONTROL INSRTUCTIONS IR BLASTER CABLE IR RECEIVER CABLE SW-HDM3D-C6-4X4E IR SOCKETS ALL IR OUT: The default location for IR blaster to transmit all IR command signals received from any of the four remote receivers to all of the HDMI sources. IR BLASTER 1-4: IR blaster connected here can only transmit IR command signals from the remote receivers that are setting at respective input channel from 1 to 4.
PAGE 10
2.6 INSTALLATION SWHDM3D-C6-4X4E To setup Avenview SW-HDM3D-C6-4x4E follow these steps for connecting to a device: Matrix Switch 1. 2. 3. 4. 5. 6.
PAGE 11
2.7 FRONT PANEL OPERATION GUIDE Preset Save Learn Default 2.8 METHOD A: PUSH BUTTON 1. IN/OUT MAP 1) Use the “+”or “-“ output push button to select the number of display 2) Use the “+”or “-“ input push button to select the number of input source “+”: change selected input/output port in ascending order “-” : change selected input/output port in descending order After you select the desired input/output port, the LED will blink twice and the setting will be effective 2.
PAGE 12
4.
PAGE 13
2.9 RS232 & ETHERNET SOFTWARE GUIDE 3 1 7 6 8 2 4 5 9 10 11 1 2 3 4 5 6 12 FW/SW Version Button COM Port Selection Connection Status Connect/Disconnect Button Power On/Off Button EDID Button 7 8 9 10 11 12 Firmware Update Button Network Button Mapping Button Default Reset Button In/Out Switch Button Mute Output Button 1. FW/SW VERSION BUTTON CLICK “ ” BUTTON TO SHOW VERSION INFORMATION www.avenview.
PAGE 14
2. COM PORT SELECTION CLICK “ ” BUTTON TO SELECT COM PORT 3. CONNECTION STATUS 1) CONNECTED STATUS: 2) CONNECTING STATUS: 3) DISCONNECTED STATUS: www.avenview.
PAGE 15
4. CONNECT/DISCONNECT BUTTON CLICK THIS BUTTON “ ” TO CHANGE CONNECTION STATUS 5. POWER ON/OFF BUTTON CLICK THIS BUTTON TO POWER ON/OFF “ ” POWER ON STATUS (BLUE): CLICK THIS BUTTON TO POWER OFF DEVICE (STANDBY MODE) “ ” POWER OFF STATUS (RED): CLICK THIS BUTTON TO POWER ON DEVICE 6. EDID BUTTON www.avenview.
PAGE 16
1) LEARN EDID FROM DEFAULT a) SELECT DEFAULT EDID(1-8 DEFAULT EDID) b) SELECT INPUT c) CLICK “LEARN” BUTTON TO LEARN DEFAULT EDID 2) LOAD EDID FILE TO INPUT a) SELECT INPUT b) CLICK “LOAD” BUTTON TO SELECT THE EDID FILE 3) LEARN EDID FROM DISPLAY a) SELECT EDID PORT b) SELECT INPUT c) CLICK “LEARN” BUTTON TO LEARN DISPLAY EDID www.avenview.
PAGE 17
4) CREATE EDID FILE a) CLICK “CREATE” BUTTON TO CREATE EDID FILE b) SELECT THE EDID CONTENT c) CLICK “SAVE EDID ON COMPUTER” TO SAVE THE GENERATED EDID AS A FILE VIEW EDID CONTENT a) SELECT INPUT, OR FROM FILE b) CLICK “VIEW” BUTTON TO READ THE EDID AND ANALYSIS www.avenview.
PAGE 18
c) CLICK “SAVE AS” TO SAVE THE READ EDID AS A FILE ON COMPUTER 7) FIRMWARE UPDATE BUTTON 1) CLICK “LOAD FILE” TO SELECT THE FIRMWARE FILE WHICH YOU WANT TO UPDATE 2) CLICK “BREAK” BUTTON 3) QUICKLY REMOVE AND RECONNECT THE POWER INPUT CONNECTOR 4) CLICK “START” BUTTON TO BEGIN THE FIRMWARE UPDATE www.avenview.
PAGE 19
8) NETWORK BUTTON 1) CLICK “READ FROM DEVICE” TO READ THE DEVICE IP ADDRESS 2) SELECT “ETHERNET” AND THEN WILL BE A POP-UP WINDOWS 3) KEY IN THE DEVICE IP ADDRESS TO THE POP-UP WINDOWS 4) CLOSE THE POP-UP WINDOWS 5) CLICK THE CONNECTED BUTTON TO CONNECT 9) MAPPING BUTTON 1) SAVE MAPPING: a) SELECT MAPPING(1-8) b) CLICK “SAVE” BUTTON TO SAVE CURRENT MAPPING www.avenview.
PAGE 20
2) PRESET MAPPING: a) SELECT MAPPING(1-8) b) CLICK “RECALL” BUTTON TO RECALL PREVIOUS MAPPING WHICH ARE SAVED 3) RENAME MAPPING: a) RENAME THE MAPPING(MAPPING1-MAPPING8) b) CLICK “CONFIRM” BUTTON TO CONFIRM THE CHANGE 10) DEFAULT RESET BUTTON CLICK THIS BUTTON TO DO FACTORY DEFAULT RESET THE DEFAULT RESET PROCESS WILL TAKE ABOUT 80~90 SECONDS 11) IN/OUT SWITCH BUTTON CLICK THE BUTTON ON THE CHECKERBOARD TO SELECT INPUT & OUTPUT PORT USER CAN CLICK THE INPUT NUMBER BUTTON TO LET ALL OUTPUTS SELECT THE SA
PAGE 21
EX: ALL OUTPUTS SELECT INPUT 3 12) MUTE OUTPUT BUTTON CLICK THE CIRCLE BUTTON TO TURN OFF OUTPUT’S VIDEO AND AUDIO EX: MUTE OUTPUT 2 www.avenview.
PAGE 22
2.10 EDID LEARNING SOFTWARE CONTROL: PLEASE REFER TO THE OPERATION APPROACH\ METHOD C: SOFTWARE CONTROL THROUGH RS-232 PORT THERE ARE EIGHT EMBEDDED DEFAULT EDID AS BELOW, 1. FULL-HD (1080P@60)-24BIT 2D & 2CH 2. FULL-HD (1080P@60)-24BIT 2D & 7.1CH 3. FULL-HD (1080P@60)-24BIT 3D & 2CH 4. FULL-HD (1080P@60)-24BIT 3D & 7.1CH 5. HD (1080I@60)(720P@60)-24BIT 2D & 2CH 6. HD (1080I@60)(720P@60)-24BIT 2D & 7.1CH 7. FULL-HD (1080P@60)-36BIT 2D & 2CH 8. FULL-HD (1080P@60)-36BIT 2D & 7.
PAGE 23
SECTION 3: SPECIFICATIONS ITEM DESCRIPTION UNITS SW-HDM3D-C6-4x4E HDM3D-C6SW-R 4x4 HDMI Matrix Switch over CAT6 HDMI Receiver over CAT5 with 3D with 3D Support Support HDMI Deep Color & Full 3D Yes Single Link 225 MHz (6.
PAGE 24
3.1 IR CONTROL GUIDE ON Power on the matrix switcher OFF Standby mode MUTE Hide or Turn off the selected Output’s Video/Audio SAVE Save current mapping mode DEFAULT EDID Default EDID selection CLEAR Clear the previous IR operation STATUS View Preset output Status PRESET Preset Mapping mode LEARN EDID Begin EDID learning from one output TAKE Trigger the previous setting A-D Input 1(A) Input 2(B) Input3(C) Input 4(D) I-IV Select the Outputs 1-4 F1 Reserved F2 Reserved www.
PAGE 25
Ex: Select Input 2 to Output 3 Push the red circle button as illustrated to select Input 2 to Output 3 Operation MUTE OUTPUT EX: MUTE OUTPUT 3 OUTPUT STATUS EX: OUTPUT 4 (INPUT 2) SAVE CURRENT MAPPING EX: SAVE CURRENT MAPPING TO 5 Procedure 7-Segment LED MUTE + A~D(OUTPUT 1~4) + TAKE 1. PRESS “MUTE” BUTTON 0 2. PRESS NUMBER KEY “C” TO SELECT OUTPUT 3 3 0 3.PRESS “TAKE” BUTTON 3 0 STATUS + A~D(OUTPUT 1~4) + TAKE 1.PRESS “STATUS” BUTTON - 2.PRESS NUMBER KEY “D” TO SELECT OUTPUT 4 4 - 3.
PAGE 26
3.PRESS “TAKE” BUTTON LEARN DEFAULT EDID EX: DEFAULT EDID 2 INPUT 3 DEFAULT EDID + A~H(1-8 DEFAULT EDID) +Ⅰ~Ⅳ(INPUT 1~4) + TAKE 1.PRESS “DEFAULT EDID” BUTTON E d 2.PRESS NUMBER KEY “B” TO SELECT DEFAULT EDID 2 2 d 3.PRESS NUMBER KEY “Ⅲ” TO SELECT INPUT 3 2 3 4.PRESS “TAKE” BUTTON LEARN EDID PORT EDID EX: LEARN EDID PORT INPUT 3 0 0 (success) F F(fail) LEARN + D(EDID PORT) +A~D(INPUT 1~4) + TAKE 1.PRESS “LEARN” BUTTON E L 2.PRESS NUMBER KEY “D” TO SELECT EDID PORT 4 L 3.
PAGE 27
Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc.