Regulations Information FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1. This device may not cause harmful interference. 2.
Safety Guideline for Using Lithium Battery (Danish) ADVARSEL! Lithiumbatteri --- Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af same fabrikat og type. Levé det brugte batteri tilbage til leverandøren. (Deutsch) VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
Optical Device Drive Notice CAUTION ✓ This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
. Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the equipment to the power inlet. 7. Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord. 8. Always unplug the power cord before inserting any add-on card or module. 9. All cautions and warnings on the equipment should be noted. 10.
WEEE Statement Before You Start 6
Trademarks All trademarks are the properties of their respective owners. ✓ Microsoft is a registered trademark of Microsoft Corporation. Windows98/ME, 2000/XP are registered trademarks of Microsoft Corporation. ✓ PCMCIA and CardBus are registered trademarks of the Personal Notebook Memory Card International Association. Release History Version Revision Note Date 2.
Before You Read The information in this user’s guide is subject to change without notice. TriGem Computer, Inc. shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. AVERATEC is a trademark or registered trademark of TriGem Computer, Inc. in the United States and/or other countries. All other product and brand names are trademarks of their respective owners.
Table of Content Before You Start Installing and Removing the Battery Pack 23 Regulations Information 1 Charging the Battery Pack 23 Safety Guideline for Using Lithium Battery 3 Optical Device Drive Notice 4 Chapter 3 Using the Notebook Computer Macrovision Notice 5 Adjusting the LCD Screen Display 25 Safety Instructions 4 The Notebook’s Hot Key Controls 27 WEEE Statement 6 The TouchPad 28 Trademarks 7 The DVD Dual/SuperMulti 32 Realease History 7 Power Saving Modes 34 Before
PC Card / PCMCIA Problems 68 Chapter 6 Running BIOS Setup Performance Problems 69 Entering the BIOS Setup Screen 50 USB2.
1 Chapter Introduction Chapter 1 Introduction 11
Unpacking First, unpack the notebook from the shipping carton and check all items carefully. If any item is damaged or missing, please contact your local dealer immediately. Keep the box and packing materials in case you need to ship the unit in for service in the future. The package should contain the following items: ✓ Notebook Computer ✓ Quick Start Guide ✓ All-in-one application disk, containing the drivers, utilities, and factory recovery image.
Introduction Welcome to the Notebook PC Congratulations on your purchase of the Notebook PC. Your Notebook features the latest advances in portable computing technology. The Notebook’s modular design provides maximum expandability without compromising portability. Getting to Know Your Computer 1 Opening the LCD Panel 2 3 WARNING ✓ To avoid damage to the display panel: 1. Try not to slam the display upon closing it. 2. Try not to place any object on top when it is closed or open. 3.
With the LCD screen open, you will see several features important for operating your Notebook computer. Front View To open, lift the top cover (LCD Panel). The image of the top-open view and descriptions below will help you to get familiarized with the main features of your notebook. 3 15 14 1 13 2 12 3 11 10 4 WARNING ✓ Do not place any heavy objects on the top of notebook. This may damage the display.
1. LCD display 2. Integrated speakers 3. Built-in microphone 4. LED Status Indicator LED Graphic Symbol Indication Blue light indicates the WLAN module is active. Persistent green light indicates the Silent mode is enabled. Blinking green light indicates the Suspend Mode is enabled. Blinking orange light indicates the battery is being charged. Blinking red light indicates the battery power is low when the system is turned ON. Persistent green light indicates the Power is ON.
9. Touchpad buttons 10. Touchpad 11. Keyboard 12. Power / Suspend button • Press momentarily to turn on the system. • Press and hold for at least 4 seconds to turn off the system. • Press the power / suspend button again to return from the suspend mode. • Persistent green light indicates the Power is ON 13. Silent mode button • CPU should be switched to Low Frequency Mode. • Pressing the key enables the system to lower its power usage; therefore the fan speed is reduced to achieve lowest operating noise.
Left Views 1 2 3 4 5 6 7 8 1. Kensington lock 2. Ventilation grill 3. Power jack (DC-in) 4. VGA port 5. Network connector (LAN) Note ✓ When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting. 6. ExpressCard (New Card) slot The slot is where Express Card (Type 54) is inserted. ExpressCard Type 54 allows insertion of 54mm and 34mm cards. ExpressCard integrates both the PCI-Express bus technology and USB2.0 standards. 7. IEEE 1394 connector 8.
Right View 1 2 3 1. USB connectors 2. CD (CD-ROM/CD-RW/DVD-ROM/COMBO/DVD Dual) drive Depending on your model, the optical drive may vary. 3.
Bottom View 3 2 1. Expansion compartment 2. Ventilation grill 3. Hard disk drive 4. Battery lock/unlock button 5.
Chapter 2 Getting Started Chapter 2 Getting Started 20
Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. To connect the computer to an external power source: WARNING ✓ Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter.
Turning On Your Notebook Computer Turn on your Notebook by pressing the power button. Hold the button down for a second or two and release. The PowerOn Self Test (POST) runs automatically. After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows Vista.... etc) is installed, it should start automatically.
Installing and Removing the Battery Pack To Remove the Battery Pack To Install the Battery Pack 1 2 Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance.
Chapter 3 Using the Notebook Computer Chapter 3 Using the Notebook Computer 24
Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. KEYS FUNCTIONS Fn + F7 Increases the brightness level. Fn + F8 Decreases the brightness level. Fn + F4 Changes Display Mode: LCD-only, CRT-only and LCD&CRT. LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: • When you are not using the computer, keep the LCD screen closed to protect it from dust.
External CRT Display You can hook up an external monitor through the 15-pin CRT connector. Three configurations are available: • LCD only • CRT only • Simultaneous display of the LCD screen and CRT monitor You can switch between these display configurations by pressing the key combination [Fn] + [F4].
The Notebook’s Hot Key Controls Function Keys (Quick Keys) Graphic Symbol Action System Control Fn + F1 Enters Suspend Mode. Fn + F3 Mute/Unmute Audio Fn + F4 Changes Display Mode: LCD-only, CRTonly and LCD&CRT. Fn + F5 Increases the speaker volume. Fn + F6 Decreases the speaker volume. Fn + F7 Increases the brightness level. Fn + F8 Decreases the brightness level.
The TouchPad The touchpad is a rectangular electronic panel located just below your keyboard. You can use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use the buttons below the touchpad as left and right mouse buttons. TouchPad Precautions The TouchPad is a pressure sensitive device. Please take note of the following precautions. • Make sure the TouchPad does not come into contact with dirt, liquids or grease. • Do not touch the TouchPad if your fingers are dirty.
1 Double click the Synaptics Pointing Device icon in the task bar. 2 After selecting the Pointer Options tab, set the point speed option in the Motion menu. Then select the Enhance pointer precision option and press the OK button.
Adjusting the touch pad sensitivity 1 Double click the Synaptics Pointing Device icon in the task bar. 2 Select the Device Settings tab, and see if the touch pad program is selected in the Devices menu. Then press the Settings button.
3 In the left menu, select the Touch Sensitivity item and move the touch sensitivity slider toward ‘Light Touch’. What is a touch sensitivity function? This function allows you to adjust how much force is required to use the touch pad. In general, to increase sensitivity shift the slide bar toward ‘Light Touch’. To decrease sensitivity, shift it toward ‘Heavy Touch’. Note ✓ If you want to use other functions for your touch pad, click on each tab and set the option properly.
The DVD Dual/SuperMulti Features of the DVD Dual/SuperMulti The features of the DVD Dual/SuperMulti are listed below. • The Audio Play feature allows you to play music CDs • Front panel load/unload button • Supports CD-DA, CD-ROM mode 1 and mode 2, Multi-Session Photo CD¢‚, CD-I/Video CD (pcs.) • Low power consumption • 12.7mm height Precautions for Handling CD Discs • Always hold the disc by the edges, avoid touching the surface. • Use a clean, dry, cloth to remove dust, smudges, or fingerprints.
Loading a Disc To play a CD disc, follow the instructions listed below. 1. Push the DVD Dual/SuperMulti eject button on the CD drive door. Gently pull the tray all the way out. 2. Carefully lift the CD disc by the edges and make sure the shiny surface is face down (the side with no writing on it). Carefully insert the CD disc onto the tray. Push the CD disc down gently so that it snaps onto the center ring. 3. Push the tray back into the drive. To remove a CD disc, do the following: 1.
Power Saving Modes This section contains information on the Notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system. The AC Adapter converts AC power from a wall outlet to the DC power required by the computer.
Removing the Battery Pack To remove the battery pack from its compartment, please refer to Inserting and Removing the Battery Pack. Preparing the Battery Pack for Use (Battery Calibration) Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status. To calibrate the battery pack follows the instructions below: 1.
Automatic Battery Pack Charging Function To charge the battery, while the battery pack is in the notebook, plug the AC adapter into the notebook and an electrical outlet. The charging time is approximately 4-6 hours when the notebook is turned off and approximately 6-10 hours when the notebook is turned on. When the battery is fully charged, the battery charge indicator turns off. Note ✓ Under heavy use or when exposed to high temperatures, the battery may take longer to charge than normal.
Battery Low Warning When the pack initially reaches the “Battery Low” state approximately 7 ~ 10 minutes of the usable battery life is left. You will hear an audible beep signal every 15 seconds alerting you to the “Battery Low” status. When the battery power reaches the “Battery Low Low” status the beeping sound will accelerate. Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data.
WARNING ✓ Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power.
Using the Windows Help Windows For Windows Vista help, click Start Help and Support icon will open the dialog box.
Recycle Bin Used for storing deleted files in case you want to recover and save it in your system. The files will only be deleted from the Recycle Bin permanently only if you empty it by right clicking your mouse and select the “Empty Recycle Bin”. Start Button Allows easy access to all Windows programs.
Taskbar When you open a program, its icon is displayed at the taskbar for you to conveniently move between programs by clicking the relevant button. To add or remove toolbars from the taskbar: right click an empty spot on the taskbar, select Toolbars choose the toolbar you want to add.
Control Panel It is in this area that you can change how Windows looks and works. Click Start interfaces - Classic View. Control Panel dialog box.
4 Chapter Desktop Operation Chapter 4 Desktop Operation 43
Your notebook is capable of providing you with efficient and productive mobile computing, it also has the speed and capacity to service as a desktop system. This chapter discusses those functions of your notebook that are typical of desktop systems. Audio The Multimedia Sound System The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software.
Audio Volume Control The Notebook is equipped with hot-key volume controls: Pressing the [Fn]+[F6] hot-key combination decreases the audio output volume, press the [Fn]+[F5] hot-key combination increases the audio output volume. Audio Software Your notebook comes equipped with an integrated sound system capable of providing you with quality audio sound through the builtin speakers or through external speakers connected via the system ports.
Chapter 5 Internet Connection Chapter 5 Internet Connection 46
There are numerous ways to connect to the Internet. This may vary from the user’s working environment as well as system specifications. • Using a wired LAN • Using a wireless LAN Using a Wired LAN for Connection to the Internet For you connect to the Internet, a wired LAN environment normally uses the company’s LAN or a broadband modem.
Using Wireless LAN Network for Connection to the Internet Chapter 5 Internet Connection 48
Chapter 6 Running BIOS Setup Chapter 6 Running BIOS Setup 49
The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacture’s default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS. The BIOS allows you to set up passwords to limit access to users.
BIOS Action Keys Function Key ESC Enter Command Exit Go to Sub Screen Description Leaves a sub-menu to return to the previous menu OR exits the BIOS setup while saving changes. Shows the Sub Menu F1 General Help Shows the Help Screen F10 Save and Exit Saves changes and reboots the computer. Select a field Selects the next field. Select an item Selects the next upper item. Select an item Selects the next lower item. - Lower value Selects the next value within a field.
Modifying the BIOS Settings The Phoenix BIOS setup main menu is subdivided into sub-menus. Each menu item is described in this section. Main Setup Under this menu, you may change time/date and view basic processor and system memory information.
Security Setup Power Setup Boot Setup Exit Setup Chapter 6 Running BIOS Setup 53
Chapter 7 VGA Utilities Chapter 7 VGA Utilities 54
After you have restarted Windows, click on the Intel® Graphics Media Accelerator Driver for Mobile icon on the lower right corner of the screen. Click on the Graphics Properties to enter the Intel® Graphics Media Accelerator Driver for Mobile display window. You can also click the touchpad or mouse right button and select the Personalize item.
Select the Display Settings option to enter its window display. Click on the Advanced Settings tab to enter Generic PnP Monitor and Mobile Intel® 4 Series Express Chipset Family window display. Select the Intel ® Graphics Media Accelerator Driver for Mobile and click on the Graphics Properties tab.
Display Devices This feature allows you to connect external display devices. Display Settings This feature allows you to adjust the color scheme, resolution, refresh rate for your display.
Color Correction This feature allows you to adjust the color rate of your display. Hot Keys This feature allows you to set the corresponding hot keys in executing the program you frequently use.
Launch Zoom This features allows you to enlarge some parts that you would like to see for a clearer view.
Chapter 8 Troubleshooting Chapter 8 Troubleshooting 60
Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter.
• If external devices such as USB cameras, scanners, printers do not function correctly when connected to the system, it is usually a problem with the device driver or the device itself. Consult the device’s manufacturer first before contacting TriGem USA support center. • Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use. Consult the software vendor for problem solving. • Legacy peripheral are not plug-and-play capable.
Sound cannot be recorded • You will need to plug-in an external microphone to the microphone connector to record sound. • Double-click the speaker icon on the lower right corner of the taskbar to see if the microphone has been muted. - Click Options and select Properties. - Select Recording and click the OK button. - After Click OK button, the recording volume control panel will appear. • Go to [Start > Settings > Control Panel] and double-click the Multimedia icon (or Sounds and Audio Devices icon).
The hard drive is making abnormal whining noises • should back up your files as soon as possible. • Make sure the source of noise is indeed from the hard drive and not the fan or other devices. The hard disk drive has reached its capacity • Run Disk Cleanup utility in Windows. [Start > All Programs > Accessories > System Tools > Disk Cleanup] The system will prompt you for what to do.
Optical Drive Problems The optical drive does not work • Try rebooting the system. • The disk is damaged or files are not readable. • After you have inserted a CD-ROM disk, it may take a moment before you can access its content. The drive dose not read any disks • The CD may not be properly seated in the tray. Make sure the disk is firmly seated onto the spindle. • The disk is damaged or not readable. The disk cannot be ejected • Normally, it takes a few seconds to eject the disk.
Display Problems The display panel is blank when the system is turned on • Make sure the computer is not in the Standby or Hibernate suspend modes. The display is turned off to conserve energy in these modes. The screen is difficult to read • The display resolution should at least be set to at least 1280x800 for optimal viewing. - Go to [Start > Settings > Control Panel] and double-click the Display icon.
The built-in keyboard accepts no input • Please try to make sure the system doesn’t hang up and is still working. The characters on the screen repeat while I type. • You may be holding the keys down too long while you’re typing. • Keep the keyboard clean. Dust and dirt under the keys could cause them to stick. • Configure the keyboard to wait longer before the auto repeat feature starts. To adjust this feature, Go to [Start > Settings > Control Panel], and double-click the Keyboard icon.
Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory • Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM. • The memory module may not be installed properly. Go back to Chapter 4 to review the details of this operation. • The memory module may be defective.
The PC card cannot be recognized • Make sure the card is fully inserted; the outer end of the card should be even with the edge of the computer. • Remove and insert the PC card again. • Make sure there is no IRQ conflict with the card. See Windows on-line help for solving IRQ conflicts. • Reboot the computer and see if the problem persists. • The card may be defective. Try the card on another system, if possible.
The program appears stopped or runs very slowly • Press CTRL+ALT+DEL to see if an application is still responding. • Restart the computer. • This may be normal for Windows when it is processing other CPU-intensive programs in the background or when the system is accessing slow-speed devices such the floppy disk drive. • You may be running too many applications. Try to close some applications or increase system memory for higher performance.
Chapter 9 Specification Chapter 9 Specification 71
CPU • Intel CPU : CoreTM 2 Duo Support, up to 1066MHz, up to 3MB an 6MB L2 Cache Package : PGA Socket P pin out Memory • DDRII 667/800 • DDRII RAM socket * 2 • DDR2 up to 4GB total Core Logic Intel Cantiga GM45 + ICH9M Support DDRII 667/800 SO-DIMM module per channel Chapter 9 Specification 72
VGA Intel Cantiga • Supports DX9 & DX10 • Dynamic Video Memory Technology (DVMT) 4.0 support • WMV9(VC-1) and H.264(AVC)support • Spread spectrum clocking (SSC) support. • Analog CRT DAC interface support. Audio Codec Realtek ALC888 • Support 7.1 multi-channels • Azalia standard support • Windows Vista Premium support IEEE 1394a • Support IEEE 1394a with Open HCI Compliance • PCI V2.
Card reader (4 in 1) • Support SD/MMC/MS/MS-Pro card • PCI interface LAN Controller Realtek 8102E • Supports 10 and 100 Mb/sec. Full/Half Duplex operation • PCI-E interface Wireless LAN (Optional) Intel Wireless WiFi Link 5100 Series • PCIe Mini card • 2 antenna supported • IEEE 802.
Keyboard • 84/85 Keys K/B Pointing Device • PS2 Touch Pad with 2 buttons w/o scroll up/down LCD • LCD is 12.1’’ WXGA, resolution 1280X800 • Glare & non Clare panel/Wide view type HDD • Support SATA II HDD, 1 x 2.5’’( 9.5mm) • 5400rpm support. Battery Pack • 4 cells Pack, 14.4/14.8V/2200mAH • 8 cells Pack, 14.4/14.
AC-Adapter • Automatics Voltage adjustment between 100 and 240VAC 50/60Hz • 65 Watts, 2pin BIOS • Support Phoenix ACPI 3.0 BIOS Physical Outline • 296 x 227 x 26.3 - 31mm (w/o rubber foot) • 1.95Kg w/ 4 cells battery Camera module support (Optional) • 1.3M module • USB interface Fixed LENs.
