AVerMedia® EB1004 BAK Real-time Security DVR Operations Manual P/N: 300AABLP MADE IN TAIWAN
FCC NOTICE This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial, industrial or business environment. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.
Table of Contents TIME SET .............................................................................................18 VGA SETUP .........................................................................................19 Introduction .........................................................................................................3 MOTION SETUP ..................................................................................19 Features and Specifications .....................................
• Full-screen resolution: Display: 720 x 480 (NTSC), 720 x 576 (PAL) Recording: 640 x 224 (NTSC), 640 x 272 (PAL) Introduction EB1004 BAK is a stand-alone, non-PC based DVR unit that provides real-time monitoring and digital recording of surveillance video. Up to four video cameras and four sensor devices can be hooked up to this DVR unit. It is also equipped with an output relay that allows connection of an alarm device.
6 : (a) Display Channel 1 in full-screen. (b) When in the OSD menu, pressing button is equivalent to entering the number "1". 7 : (a) Display Channel 2 in full-screen. (b) Pressing this button is equivalent to entering the number "2" when in the OSD menu. 8 : (a) Display Channel 3 in full-screen. (b) Pressing this button is equivalent to entering the number "3" when in the OSD menu. 9 : (a) Display Channel 4 in full-screen.
Install the Hard Drive in a Removable Case 1. Remove the removable hard drive drawer from the case. 2. 3. Remove the upper cover of the drawer. Connect the power connector to the hard drive as the right picture shows. Install a Removable Hard Drive Case in a PC (Optional) For users who purchase an optional hard drive case, please follow the steps to install the case in a PC. 1. Power off your PC and remove the cover of your PC. 2. Remove a front cover and free a 5 1/4” drive bay.
Connect the video output of each video camera or composite video source to the CH1 ~ CH4 connectors. • VGA monitor Connect a VGA monitor to the VGA OUT connector of the DVR unit to use as a display for video surveillance and playback. • Power adapter Plug the provided 110V AC or 220V power adapter into the DVR unit's power socket. Optional Devices • Television monitor Use a BNC-to-RCA adapter to connect a regular TV monitor to the DVR unit's VIDEO OUT connector.
Use the following front panel buttons to select the desired video camera to display in full screen: CH1: Camera 1 CH2: Camera 2 CH3: Camera 3 CH4: Camera 4 Note: The recording mode can be selected in the OSD main menu. 2 Video Recording and Playback If you want to switch to the other hard drive or search for a range of video recordings, press . The ">" arrowhead cursor will then move up to the top of the screen.
MAIN MENU Setup Menu 1 Press the MENU button to display the OSD main menu.
VIDEO QUALITY There are three video quality settings to choose from: BEST, GOOD or NORMAL. (1 2 3 4) : Switch on all camera displays. (1 - - 4) : Switch on camera display 1 and 4 only. (- 2 3 -) : Switch on camera display 2 and 3 only. (- - - -) : Disable all camera displays. RECORD SELECT This determines which of the cameras surveillance video will be recorded from. The way to select cameras is the same as CAMERA SELECT.
The factory default password is "111111". Use the following front panel buttons to input a numeric password: To customize the recording schedule: Each number in the PROGRAMMED RECORD menu represents the time schedule (in hours) for recording, and the "v" cursor indicates the time that is selected. Press or to move through the time schedules. Press the SELECT button repeatedly to cycle through these settings: ( T ) For automatic non-stop video recording ( S ) For sensor recording.
VGA SETUP . You will see the screen To setup all camera, press shows MOTION CAMERA 1 2 3 4. Press the same button again to cancel the setting. VGA SETUP > RESOLUTION REFRESH RATE 1024 ^ 768 60HZ To setup channel 1 and 4 only, press . You will see the screen shows MOTION CAMERA 1 4.Press the same buttons again to cancel the setting.
HARD DRIVE SETUP SENSOR SETUP HARD DRIVE SETUP SENSOR SETUP > OVERWRITE ENABLED YES MASTER HDD SIZE 80072MB MASTER HDD USED 16014MB 20% MASTER HDD FORMAT SLAVE HDD SIZE N/A SLAVE HDD USED N/A SLAVE HDD FORMAT > SENSOR RECORD TIME ALARM OUT TIME CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 PRESS (< , >), THEN(SELECT) PRESS (MENU) TO EXIT 15 05 NORMAL-CLOSE NORMAL-OPEN NOT INSTALLED NOT INSTALLED PRESS (< , >), THEN(SELECT) PRESS (MENU) TO EXIT OVERWRITE ENABLED SENSOR RECORD TIME This allows old video
Connect to a PC 3. Select a language. Click Next to continue the installation. 4. Please click Browser.. to change the directory if it is necessary. Click Next to continue the installation. EB1004 BAK provides a convenient tool to trace back the recorded surveillance video, catch specific images and save as AVI files. With the EB-DVR Playback Application, users can play back the surveillance video, catch images and backup all recorded images easily .
Operating EB-DVR Playback Application Click to run the application. Select the Hard Disk and click OK. 5. Backward play: Play the video backward. 6. Play one frame: Display a forward static frame. 7. Back one frame: Display a backward static frame. 8. Pause: Pause the playback. 9. Forward Search: Fast play the recorded video to search an appointed image. Note: The DVR’s HDD number will be next to your PC’s HDD number.
Free Video Playback After selecting the appointed hard drive, click to select an event and click OK to play back the appointed surveillance. When you click the Event List icon, it pops-up an event table as the following illustration shows. You will see the table shows Record mode, Start time and End time of each event. Record Mode can be “T”, “M” or “S”. “T” represents Total Recording, which means the camera keeps on recording continually.
Users can backup or catch the data in DVR unit’s hard disks by saving the recorded video as AVI files and play the files by Windows Media Player. Click to save an appointed surveillance video. After clicking the icon, a window shows to request the file name and directory. Click Save to start the recording. Click again to finish the recording. EB-1004 BAK allows user to backup data in its master hard disk through a USB cable.