AVerMedia® AVerDiGi EH5108/EH5216 series EH5108/EH5108+/EH5108 Lite EH5216/EH5216+/EH5216 Lite EH5108H/EH5216H series EH5108H/EH5108H+/EH5108H Lite EH5216H/EH5216H+/EH5216H Lite EXR5008/EXR5016 series EXR5008/EXR5008+/EXR5008 Lite EXR5016/EXR5016+/EXR5016 Lite User Manual June 2010
FCC NOTICE (Class A) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission Statement NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION IF THERE IS ANY DAMAGE, SHORTAGE OR INAPPROPRIATE ITEM IN THE PACKAGE, PLEASE CONTACT WITH YOUR LOCAL DEALER. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT MODIFICATION NOTICE - INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. - THE INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.
Table of Contents Chapter 1 Introduction ........................................................................................... 1 1.1 Package Content .................................................................................................................... 1 1.1.1 EH5108 series .................................................................................................................... 1 1.1.2 EH5216 series .............................................................................
2.2.2.2 Setup the IP PTZ Camera ........................................................................................ 36 2.2.3 Using Event Log Viewer ................................................................................................... 37 2.3 Familiarizing the Buttons in Playback Mode ......................................................................... 38 2.3.1 To Cut and Save the Portion of the Recorded Video ........................................................ 40 2.3.
.1.1 To Setup Remote System Setting ..................................................................................... 92 6.1.1.1 System Setting ........................................................................................................... 92 6.1.1.2 Camera Setting .......................................................................................................... 94 6.1.1.3 Record Setting ................................................................................................
Introduction 1.1 Chapter Package Content 1.1.1 EH5108 series a b c (1) (2) (3) (7) (5) (4) (6) (8) (1) DVR unit a. EH5108 b. + EH5108 c. EH5108 Lite (2) AVerMedia USB optical mouse (3) Quick Installation Guide (4) Power adaptor (5) Power Cord * The power cord varies depending on the standard power outlet of the country where it is sold.
1.1.2 EH5216 series a b (1) (2) (3) (7) c (5) (4) (6) (8) (1) DVR unit a. EH5216 b. + EH5216 c. EH5216 Lite (2) AVerMedia USB optical mouse (3) Quick Installation Guide (4) Power adaptor (5) Power Cord * The power cord varies depending on the standard power outlet of the country where it is sold.
1.1.3 EH5108H series a b c (1) (2) (3) (7) (5) (4) (6) (8) (9) (1) DVR unit a. EH5108H b. EH5108H + c. EH5216H Lite (2) AVerMedia USB optical mouse (3) Quick Installation Guide (4) Power adaptor (5) Power Cord * The power cord varies depending on the standard power outlet of the country where it is sold.
1.1.4 EH5216H series a b (1) (2) (3) (7) c (5) (4) (6) (8) (9) (1) DVR unit a. EH5216H b. EH5216H + c. EH5216H Lite (2) AVerMedia USB optical mouse (3) Quick Installation Guide (4) Power adaptor (5) Power Cord * The power cord varies depending on the standard power outlet of the country where it is sold.
1.1.5 EXR5008/EXR5016 series a (2) (5) (4) (3) (7) c b (1) (6) (8) (1) DVR unit a. EXR5008/EXR5016 b. + EXR5008 /EXR5016 + c. EXR5008 Lite/EXR5016 Lite (2) AVerMedia USB optical mouse (3) Quick Installation Guide (4) Power adaptor (5) Power Cord * The power cord varies depending on the standard power outlet of the country where it is sold. (6) SATA cables (7) Screws for HDD installation (8) Software CD (User Manual included) 1.1.
1.2 Front Panel 1.2.1 EH5108 Lite/EH5108H Lite/EH5216Lite/EH5216H Lite EXR5008 Lite/EXR5016 Lite Name (1) System Power indicator Function System power status indicators. Indicate running state of system. Lights when the system is running. (2) Record indicator When DVR system is recording, the light will keep flashing.
Name Function (9) Call out system setup menu on preview mode Move to left direction on menu control To move PTZ camera lens to left in PTZ mode Move to right direction on menu control To move PTZ camera lens to right in PTZ mode (10) Control Buttons To move PTZ camera lens to up Move to up direction on menu control To move PTZ camera lens to down Move to down direction on menu control Confirm or make a selection - Channel camera selection number in playback and preview mode.
Name Function A functional key for multiple system control. Press to switch to FN mode (The word “FN” will show up in the left bottom corner on screen). Press exit FN mode (The “X” will show up in the left bottom corner on screen).
1.2.3 EH5216/EH5108/EXR5008/EXR5016 Name (2) IR Sensor port Function - Power indicator (left): System power status indicators. Indicate running state of system. Lights when the system is running. - Record indicator (right): When DVR system is recording, the light will keep flashing.
Name Function Move to left direction on menu control To move PTZ camera lens to left in PTZ mode Move to right direction on menu control To move PTZ camera lens to right in PTZ mode (9) Control Buttons To move PTZ camera lens to up Move to up direction on menu control To move PTZ camera lens to down Move to down direction on menu control Confirm or make a selection - Channel camera selection number in playback and preview mode. For the channel over 10, press press ~ - Press - character mode.
Name Function A functional key for multiple system control. Press to switch to FN mode (The word “FN” will show up in the left bottom corner on screen). Press exit FN mode(The “X” will show up in the left bottom corner on screen).
1.3 Back Panel 1.3.1 EH5108 series/EH5108H series Name Function (1) LAN Port For Gigabit Ethernet connection (2) RS232 port For POS device connection (3) Audio In/Out/MIC In Output the audio signal to audio output device i The audio input and output device has its own power supply is necessary.
Name Function (7) eSATA port For connecting with eSATA RAID (8) RS485 For analog PTZ camera connection (also see Chapter 1.6) (9) Sensor In Support up to 16 sensor devices (10) Relay Out Support 4 relay devices (Relay: 1A @ 125V AC/30V DC) (11) CH1~ 16 Input the video camera signal and display it on channel 1~ 16 (12) 19V DC connector Connect the power cord into this port 1.3.
1.4 Setting Up the DVR Unit 1.4.1 Installing the Hard Disks i - - For hard disk spec, please referring to http://www.avermedia.com/AVerDiGi/Product/ → Embedded Hybrid DVR/NVR → AVerDiGi EH5108 series / EH5216 series/EH5108H series/EH5216H series or Pure NVR → AVerDiGi EXR5016 series → Hardware Recommendations The external USB hard disk only supports on file backup. Please do not install the external USB hard disk for recording purpose.
5. The hard disk plate can be installed 3 hard disks. User can choose the position and place the hard disk on it. 6. Turn the plate and hard disk over carefully and screwed the hard disk on the plate. If hard disk cannot be fit to the screw hole, then, you may adjust the hard disk position to fit the screw hole. 7. The look of three hard disks is installed on hard disk plate. 8. Plug the SATA cable into SATA connector on the PC board.
11. Screw the plate within hard disk inside the DVR unit 12. Plug the SATA cable into the left side hard disk. When user remove power cable from hard disk, please DO NOT pull the power cable straight way. Please pull out the power cable by moving power connector to left and right side and slowly pull out the power cable from hard disk. i User can adjust the step 9, 10, and 11 for easily install process if necessary. th 13. If user wants to install 4 HDD, then follow the steps to continue.
16. Plug the SATA cable into SATA connector on the PC board. 17. Plug the power cable to the hard disk. 18. Plug the SATA cable to the hard disk. i The SATA cable is an optional accessory. Please purchase from your dealer. 19. Place the HDD holder inside the DVR unit. The screw hole of HDD holder is aligning with screw hole on the DVR unit.
20. Push the HDD holder forward and screw hole of HDD holder will match the screw hole on the DVR unit and HDD holder should hook on the stabled hook on the DVR unit. 21. Screw the HDD holder inside the DVR unit. 22. Screw the holder on the DVR unit. 23. The look of four hard disks are installed. 24.
1.4.2 Connecting Devices 1.4.2.1 EH5108 series/EH5108H series The back panel of the DVR unit, user can connect up to 8 cameras in combination of analog and IP camera. The DVR unit also can connect 16 sensor devices, 4 alarm devices, and output video to a TV or CRT/LCD monitor.
EH5108 Lite/EH5108H Lite (Optional) EH5108H Pen drive and external hard disk must be FAT32 format. i – – All connected devices have its own power supply is necessary. DVR unit can connect 8 cameras in analog and IP cameras combo.
1.4.2.2 EH5216 series/EH5216H series The back panel of the DVR unit, user can connect up to 16 cameras in combination of analog and IP camera. The DVR unit also can connect 16 sensor devices, 4 alarm devices, and output video to a TV or CRT/LCD monitor.
EH5216/EH5216H (Optional) EH5216 Lite/EH5216H Lite (Optional) Pen drive and external hard disk must be FAT32 format. i – – All connected devices have its own power supply is necessary. DVR unit can connect 16 cameras in analog and IP cameras combo.
1.4.2.3 EXR5016 series The back panel of the DVR unit, user can connect up to 16 IP cameras. The DVR unit also can connect 16 sensor devices, 4 alarm devices, and output video to a TV or CRT/LCD monitor. Follow the illustration below to make the connection: For backup recorded video, plugging the pen drive or external hard disk through USB port that are located at front panel of DVR unit, and then, use the bundled software enables user to transfer, playback and segment the video.
EXR5016 (Optional) EXR5016 Lite (Optional) Pen drive and external hard disk must be FAT32 format. i – – All connected devices have its own power supply is necessary. DVR unit only can connect 16 IP cameras.
1.5 Sensor, Relay and RS485 pinhole allocation 1.5.1 EH series The Sensor and Alarm enable you to connect 16 sensor inputs, 4 relay outputs and PTZ cameras. Just connect the external sensor, relay, and PTZ camera pin directly to the pinhole. Check the table below and locate which pinhole is assigned to sensor input and relay output. 1.5.1.1 Sensor Pin Definition Sensor Pin # 1.5.1.
1.5.2 EXR series The Sensor and Alarm enable you to connect 16 sensor inputs and 4 relay outputs. Just connect the external sensor and relay pin directly to the pinhole. Check the table below and locate which pinhole is assigned to sensor input and relay output. 1.5.2.1 Sensor Pin Definition Sensor Pin # 1.5.2.
1.6 Familiarizing the Remote Control Buttons Use the Remote control to operate the DVR unit.
Name Function (13) i - + : Enable/disable auto scan + : Switch to full screen + ~ doesn’t have any functions. Switch to character mode. Press to enter EN mode (The word “EN” will show up in the left bottom corner on screen). User can press the character button and press rapidly to find the character that wants to enter. Press button again to exit EN mode (The “X” will show up in the left bottom corner on screen).
Name Function Speed + : To speed up movement of PTZ camera lens (18) Speed - :To speed down movement of PTZ camera lens - As a number key for entering password in playback and preview mode ~ - Channel camera selection number in playback and preview mode (19) As a preset position with ~ + + With button can switch to different screen display modes and enable auto scan and full screen. (see also Chapter 1.
Using the DVR Software 2.1 Chapter 2 The Way to Operate DVR There are three ways can be managed the DVR unit: 1. Using mouse and keyboard Connecting the mouse and keyboard through USB interface, user can manage the DVR unit easily. For the first time using DVR unit, mouse and keyboard is the best way to set up all DVR relevant configurations. 2.
e. When formatting is done, click OK. 5. Setup the date and time in order to have correct recording time and date. Following the below steps to setup date and time: a. Click Setup and enter the password b. In Time section, click Setting button of System Time. c. Select the date and adjust the time, and then, click OK. 6. Following the below steps to connect the IP and analog camera. To connect analog camera(For EH series only) a. Plug the analog camera video cable into DVR video port. b.
2.2 Familiarizing the Buttons in Preview Mode EH5216/EH5216H series UI Name Function (1) Exit - (2) Split Screen Mode i Reboot: To restart the DVR system. It is required to enter the password Power Off: To shut down the DVR system. It is required to enter the password Login: Using different ID to login to DVR system. Cancel: To return to DVR application. Select from 6 different split screen types to view all the camera, or one camera over the other or alongside on a single screen.
Name Function (12) Snapshot i Capture and save the screen shot in *.jpg format. Please plug the USB pen drive to DVR server before press Snapshot button. (13) Event log Show the record of activities that take place in the system. (see also Chapter 2.2.3) (14) AutoScan Start/Stop video screen cycle switch. (15) Full screen View in full screen. To return, press the right button of the mouse or ESC on the keyboard or click the arrow icon.
and to display the video at the upper right corner of the Emap screen. At the lower right corner of the Emap screen, it lists all the warning message. 3. Click Close to exit Emap screen. 2.2.2 Familiarizing the Buttons in PTZ Camera Controller (5) (4) (3) (2) (1) (6) (11) (7) (8) (9) (10) Name Function (1) Close (2) Setup Exit PTZ camera controller. Configure PTZ cameras.(see also Chapter 2.2.2.1 and Chapter 2.2.2.
2.2.2.1 1. 2. 3. 4. Setup the Analog PTZ Camera Select the channel of analog PTZ camera on Preview UI. Click PTZ button from preview UI. In the PTZ control panel, click Setup (see also Chapter 2.2.2). When the PTZ Setup dialog box appears, select the camera number and check the Use PTZ box. Use to adjust the lens of PTZ camera for preset position setting. 5. In the Connection Settings section, fill in the following selections. Then, click Save to keep the settings.
2.2.2.2 Setup the IP PTZ Camera When IP PTZ camera has successful connected with the DVR system, user can use the PTZ function directly without any configuration. To make connection of IP PTZ camera, please refer to Chapter 3.2.1. In PTZ camera panel, user can setup the preset position of the camera. The number of preset positions are depend on the IP PTZ camera that user has connected. For example: A brand of IP PTZ camera only supports 4 preset positions.
2.2.3 Using Event Log Viewer Show the record of activities that take place in the system. 1. 2. 3. 4. Click the Event Log button on DVR system main interface. The Event log viewer window will show up. Select the Date to view. To filter the records, select and click the select button to display Event, System, Operation, Network or All. Use the scroll button to go next, previous, first, or last page of event list. Also, user can enter the page number in Page column to go to the page.
2.3 Familiarizing the Buttons in Playback Mode To switch in Playback mode, click Playback button at the lower right corner of Preview mode user interface. EH5216/EH5216H series UI Name Function (1) Split Screen Mode Select from 6 different split screen type to playback the recorded video file of all the cameras or one camera over the other or alongside on a single screen. i – When you are in single screen mode, Right click and Drag a square on the area you want to enlarge.
Name Function (6) Preview (7) Playback (8) Status bar (9) Camera ID Switch to Preview mode. Switch to Playback mode. This allows you to view the recorded video file. Display the recorded date, time and play speed. Show the number of cameras that are being viewed. When you are in single screen mode, click the camera ID number to switch and view other camera. Export includes Snapshot, Output Video Clip, and Backup function. Snapshot: Capture and save the screen shot either in *.jpg format.
2.3.1 1. To Cut and Save the Portion of the Recorded Video Use the Playback Control buttons or drag the bar on the playback progress bar and pause on where you want to start the cut. Then, click Segment to set the begin mark. 2. Use the Playback Control buttons or drag the bar on the playback progress bar and pause on where you want to end the cut. Then, click Segment to set the end mark. To cancel segmentation, click Segment button again. 3.
2.3.3 Using Visual Search 1. Click Visual Search. 2. In the Visual Search Setting dialog box, select the Camera number and the date. Then click OK. 3. When a series of frames appear by date, click on the frame to display another series of frames and search by every Hour of that date, every Minutes of that hour, and every Seconds of that minute. Using and last page of time page. To go back last time selection (hour, minute, or second), click . To close event search, click .
2.3.4 Using the Event Search 1. Click on the video screen on where you want to search. 2. Click Event Search. The Event Search Setting dialog box would appear on the screen. 3. In the Event Search Setting dialog box, check the type of condition you want to search. Then, click OK to start searching. The video search would stop at the frame that matches the condition. To keep on searching click . 4. You may also set to search and list all the result.
Customizing the DVR System In the Preview screen mode, click Chapter 3 button to customize your DVR. When the DVR configuration setup selection appears, select and click the buttons you want to change the setting. 3.1 System Setup In the System Setting dialog box, click OK to accept the new settings, click Cancel to exit without saving. (11) (1) (12) (2) (3) (4) (5) (13) (6) (7) (14) (8) (9) (10) (1) Storage Path Set the HDD on where to save the data.
(2) Delete recorded data after If you want the system to automatically erase the data after a certain days, enable the Delete recorded data after check box and enter the number of days in Days text box. (3) Delete event and alarm log after If you want the system to automatically erase the event and alarm log after a certain days, enable the Delete event and alarm log after check box and enter the number of days in Days text box.
5. 6. Click + one by one to complete the adjustment. To disconnect touch monitor, click Disconnect button first, and then, turn off the power of touch monitor and remove the connection between DVR server and touch monitor. (10) POS Set from which camera screen to display the data from the POS equipment. Click Setting, to set the POS Console Setting. 1. In the POS Console Setting dialog box, click Add to set a new POS setting, Modify to change the POS setting, and Delete to remove the selected POS setting.
(1) Name: Enter a name to identify the POS. (2) Protocol: Select the protocol. (3) Skip first: Set the number of lines you want to be removed. (4) Font Color: Select the text color of the POS data. (5) Port Setting : Select the Local(Com port) where it is connected and Baud Rate. (6) Map to Channel: Select to which camera number to display the transaction text. EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (7) Text Filter: Enter the word you want to be removed.
CPU usage status Click X to close the display. (12) Login Enable the conditions in Login section you want the system to automatically carry out. - Auto Login after system boot up Execute the DVR when the operating system is started. - Auto Record after system boot up Automatically start video recording when the DVR is executed. - Auto start Network after system boot up Automatically start network connection when the DVR is executed.
3. Select the USB pen drive if there is more than one USB storage device from drop down list. The DVR unit will auto detects the firmware. 4. Click OK to start upgrading. IPCam Module Firmware Update: Update firmware of IP camera. 1. Save the firmware on root directory of USB pen drive. And then, plug USB pen drive to DVR server. 2. Click Update button, a Firmware Upgrade windows will show up. 3. Select the USB pen drive if there is more than one USB storage device from drop down list.
3.2 Camera Setup The DVR system supports 8/16 cameras in combination of analog and IP cameras, only analog cameras, or only IP cameras. 3.2.1 To Setup IP Camera(For EH series) Click Default will back to the factory default value. EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera.
1. Click the radio button of Protocol to start setup IP camera. 2. Select the Protocol, Model, Video Format, and Channel of the IP camera. 3. Enter IP address and connecting port in IP Camera Site column. 4. Also, user can enter URL of IP camera instead of IP address. 5. If the IP camera has authority request, please enable Authentication and enter ID and Password. 6. Click OK to connect with the IP camera. Detail: To adjust IP camera parameters, click Detail.
Relay Setting 1. Click Relay button. 2. Click the drop-down list and select the relay ID number. 3. Enter relay name in Name column 4. The system automatically detects the camera and input relates information. In the Content section, enter relay Description. 5. In the test section, click Test to check the relay status. Red is high and Green is low. 6. Click OK to exit and accept the setting and Cancel to exit without saving the setting.
3.2.2 To Setup IP Camera(For EXR series) Click Default will back to the factory default value. (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera. When there is no video source on the camera, we suggest disabling it so that the system won’t detect it as video loss error. (3) Input Select the camera type as IP Camera. (4) Camera - Display Enable/disable to show the video.
7. Click the radio button of Protocol to start setup IP camera. 8. Select the Protocol, Model, Video Format, and Channel of the IP camera. 9. Enter IP address and connecting port in IP Camera Site column. 10. Also, user can enter URL of IP camera instead of IP address. 11. If the IP camera has authority request, please enable Authentication and enter ID and Password. 12. Click OK to connect with the IP camera. Detail: To adjust IP camera parameters, click Detail.
Relay Setting 1. Click Relay button. 2. Click the drop-down list and select the relay ID number. 3. Enter relay name in Name column 4. The system automatically detects the camera and input relates information. In the Content section, enter relay Description. 5. In the test section, click Test to check the relay status. Red is high and Green is low. 6. Click OK to exit and accept the setting and Cancel to exit without saving the setting.
3.2.3 To Setup Analog Camera(For EH series Only) Click Default will back to the factory default value. EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (6) (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera. When there is no video source on the camera, we suggest disabling it so that the system won’t detect it as video loss error.
3.2.4 To Setup Camera from the Remote DVR User can add the camera from another DVR through the network. - EH5108/EH5108H/EXR5008 series only has 8 channels will be available. EXR series will not have the Analog Camera selection for input. (1) (2) (3) (4) (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera.
- Channel Select the channel of connected camera - Connect Click to connect the camera when all configurations are set. 3.3 Recording Setup 3.3.1 Setup IP Camera Record Setting EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (1) Camera Icons Select the camera number you want to set the recording setting. To select all the cameras, enable the ALL check box. To select more than one camera, Right click on the camera icon.
- No Recording The system won’t do any recording. (3) Motion Detection Adjust the sensitivity of the motion detection. The higher the value, the finer the sensitivity is detected. When it detects a motion, a green triangle mark would appear at the upper left corner of the screen. For EXR series, if motion detect of IP camera is enable (see also Chapter 3.2.2), the DVR system will based on the IP camera’s motion detect setup for motion recording. 3.3.
Automatically switch to record at the maximum frame rate setting once a motion is detected and recording time will be based on Stop Record After setting; if there is no motion, it records at the minimum frame rate setting. Set the frame rate in (5) Frame Rate. - No Recording The system won’t do any recording. (3) Motion Detection Adjust the sensitivity of the motion detection. The higher the value, the finer the sensitivity is detected.
3.4 Network Setup Click Default will back to the factory default value. EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (5) (2) (6) (3) (4) (7) (1) Server Name Assign a name for the DVR unit. Alphabet letters and numbers only. (2) Transmitting Cameras Select and click on the camera number in the Transmitting Camera section you want to make it accessible via internet using WebViewer, Remote Console, PDA Viewer and JAVAViewer (still image).
- DNS: Domain Name Server translates domain names (such as www.abb.com.tw) to IP addresses. Enter the IP address of DNS if it is available. MAC Address: An identifier hardware address of DVR unit that is assigned by the manufacturer for identification. User don’t need to fill in, it will generated by system automatically. Obtain an IP automatically (DHCP): Assign the IP address by local DHCP server to DVR system.
- Network Bandwidth Limit By Channel: Set the network bandwidth by each channel. All: Set the total network bandwidth consumption limit.
3.5 Schedule Setting Schedule to record, enable network, reboot and disable alarm of all the cameras either weekly or one time. The number from 00 to 23 represent the time in 24-hour clock. The left most column display the days in a week. To Set the Schedule Setting: 1. Select the date in the calendar. Use and buttons to shift the calendar to the left or right. 2. Select the condition you want to schedule in the drop down list.
3.6 i Backup Setup While backup, the CPU usage will be near to 100% and might slow down the DVR system response. In the Backup Setting dialog box, the number from 00 to 23 represent the time in 24-hour clock. The numbers from 01 to 16 represent the camera number. When you back up the file, you may find Qplayer application included in the backup folder. User need to execute the Qplayer installation on PC for playback (see also Chapter 3.6.1). EH5216/EH5216H series UI 1.
3.6.1 Using QPlayer to Playback Backup Video You can playback the backup files by using QPlayer applications on the PC. When you back up the recorded file, QPlayer applications are automatically included in the backup folder if user has enabled the selection of Inculde player when backup when backup recorded file. With QPlayer, it is the same as in Playback mode and supports different split screen types to view all the video at the same time.
Name Function (6) Archive Select the date on the calendar and the time from 00 to 23 to where to start playing the recorded video file. – OPEN FILE: user can open the recorded file from HDD – Channel 01~ 16&Channel 17 ~ 32: If the channels are over 16, click button to switch to different channel group of playback calendar. – Day Light Saving: the playback calendar will show the available video records during day light saving time period. i The numbers from 00 to 23 represent the time in 24-hour clock.
Name Function (13) Find Next Search for the next event or changes in the motion detector frame. You can use this when you are using Intelligent Search or Event Search function. Search from the recorded activities that were recorded in event log (i.e., Sensor, Motion, Video Loss). (See also Chapter 3.6.3) (14) Event Search (15) Intelligent Search (16) Audio (17) De-interlace 3.6.2 Search the changes in the motion detector frame (See also Chapter 3.6.4).
3.6.4 To Search Using the Intelligent Search 1. Click on the video screen on where you want to search. 2. Click Intelligent Search. The Intelligent Search text (red) would appear at the lower left corner of the screen. 3. When the Intelligent Search Setting dialog box and motion detector frame appear, you may adjust the sensitivity bar and the motion detector frame size and location. To set motion detector frame size and location, left click and drag on the screen. Then, click OK to start searching.
3.7 Sensor Setting The I/O device must be installed to use this function. 1. Click the drop-down list and select the sensor ID number. 2. Enter sensor name in Name column. 3. The system automatically detects the card and input number. In the Content section, enter Description of sensor. 4. In the test section, click Test to check the sensor status. Red is high and Green is low. 5. Click OK to exit and accept the setting and Cancel to exit without saving the setting.
3.8 Relay Setting The I/O device must be installed to use this function. 1. Click the drop-down list and select the relay ID number. 2. Enter relay name in Name column. 3. The system automatically detects the card and input number. In the Content section, enter Description of relay. 4. In the test section, click Test to trigger relay. Red is high and Green is low. 5. Click OK to exit and accept the setting and Cancel to exit without saving the setting.
3.9 Alarm Setting In the Alarm Setting dialog box, click Add to insert and set new alarm setting, click Delete to remove the selected alarm setting, click OK to exit and save the setting, Cancel to exit without saving. Click Default will back to factory default value. (1) (2) (8) (3) (4) (5) (6) (7) 1. Click Add to insert and set a new alarm setting. Click the items in the (8) Alarm Setting List if you want to modify the alarm setting. 2. In (1) No./Name/Description enter alarm name and description.
- Enable/disable the Abnormal Event check box, to set the condition of the event for system to alarm. Reboot: when the DVR system reboot without abnormal condition, the system will send out the alarm message. Abnormal Reboot: when the DVR system reboot in irregular condition, the system will send out the alarm message. Recording is switched off: when the recording has been stopped, the system will send out the alarm message.
- Enlarge Camera View Switch to only display video in Preview mode from where the alarm is activated. a. Select the camera from drop down list to specify which camera video to be enlarged on screen when the alarm is triggered. b. Retrieve time: set the waiting duration before system switching back to original Preview mode. If the retrieve time is un-mark, the alarm video will keep enlarging until user switch back to Preview mode manually. The retrieve time range is 0~ 600 seconds.
- IP Camera Relay: Set to enable/disable the relay operation when the alarm is activated. - Play Warning Sound Play alarm sound. - Send E-mail Send an electronic text message. Beside the Send Email check box, click Detail. In the E-mail Setting dialog box, click OK to exit and save the setting and Cancel to exit without saving the setting. (1) (2) (1) Mail Server Enter the SMTP Server and port. If your e-mail system requires user identification, enable Authentication check box and enter ID and Password.
- Start Recording Record the video from the selected camera. EH5108/EH5108H/EXR5008 series only has 8 channels will be available. 1. Beside the Start Recording check box, click Detail. 2. In the Alarm Recording Setting dialog box, select the camera to enable/disable video recording. Enable All to select all cameras. 3. In the Frame Rate selection, select As Setting to record the number of frames based on the Recording Setting. 4.
3.10 User Setup Only administrator level authority can access User Setting. The maximum user accounts are 32. In the User Setting dialog box, click Add to insert a new user, Delete to remove the selected user, Edit to modify the user control right, OK to exit and accept the setting, and Cancel to exit without saving the setting. To Add a User Account: 1. In the User Setting dialog box, click Add. 2. Select and fill in the following information.
(3) Web Viewer Enable/disable Web Viewer control right that allow the user to operate from a remote location using internet explorer. - Remote Console Allow the user to remote modify DVR system setting. - Remote LogViewer Allow the user to view the event log from remote site. - IP Camera Enable/disable user to add new IP camera when using the Web Viewer. - Remote Access Time Enable Infinite check box to access DVR without time limit.
Using the UPC to Playback Backup File 4.1 Chapter 4 Recommended System Requirements Pentium® 4 2.4GHZ or above Windows® 2000/ XP/Vista/7 DDR 256 MB Graphic function must support DirectDraw Audio card or built-in Speaker 1 available USB2.0 port 4.2 Installing the USB Playback Console To install the USB Playback Console: 1. Place Installation CD into the CD-ROM drive. When the installation main screen appears, click Install USB Playback Console and then follow the on screen instructions 2.
4.3 Familiarizing the Buttons in USB Playback Console To run the application, click the Name icon on the PC desktop Function (1) Exit Exit/Minimize the application or chose Cancel to go back to the application. About: shows DVR application version information. (2) Progress bar Show the progress of the file being played. You may move the bar to seek at any location of the track.
Name (4) Playback Control Buttons Function Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame by frame. Slower: Play the recorded video file at the speed of 1/2x, 1/4x, 1/8x, or 1/16x. Rewind: Wind back the recorded video file. Pause: Briefly stop playing the recorded video file. Play: Play the recorded video file. Faster: Play the recorded video file at the speed of 2x, 4x, 8x, or 16x Next: Go to the next frame by frame.
Name Function (16) Intelligent Search (17) Sound /Sound bar (18) De-interlace 4.3.1 Search the changes in the motion detector frame(see also Chapter 4.3.7). Turn on and off the sound Adjust the volume To enhance the video quality. Set the de-interlace mode to #1, if you are capturing motionless picture and select #2, if it captures lots of movement. To Cut and Save the Portion of the Recorded Video 1.
4.3.2 1. Playback DVR Recorded File from Hard Disk 4. Please have the hard disk which containing of recorded video data install on your PC or using external USB enclosure to connect to your PC. Click Open File button Select DVR Recorded File(HD) and click OK. Select the hard disk drive from Select Disk window and click OK. 5. And then, Playback Date/Time Selection window appears. Select the date and time and click OK. 2. 3.
4.3.3 Playback Backup File(*.dvr) 1. 2. 3. Click Open File button. Select Backup File(*.dvr) and click OK. Select to open by date or by file. 4. Open by date, located the backup file and select the date folder. 5. And then, Playback Date/Time Selection window appears. Select the date and time and click OK. 6. Open by file, located the backup file folder and click OK. i When open the backup video file, just locate the folder that has backup file.
4.3.4 To Backup Recorded File HDD backup function allows user to backup recorded file from hard disk. 1. Click Adv. Function → HDD Backup on USB Playback Console UI. 2. Select the source hard disk. 3. In Backup date/time selection windows, select the date and time. 00-24 represents hours and 01-16 represents channels. Blue block means there has recorded file. Red block means the block has been selected. Click-and-drag can select multiple block at once. 4. Click Backup to start backup file. 5.
4.3.5 To Search Using the Visual Search 1. Click Visual Search. 2. In the Visual Search Setting dialog box, select the Camera number and the date. Then click OK. 3. When a series of frames appear by date, click on the frame to display another series of frames and search by every Hour of that date, every 3Minutes of that hour, every 10 Seconds of that minute, every Second of that 10 seconds. To go back, click . To view from the selected frame and close event search, click .
4.3.6 To Search Using the Event Search 1. Click on the video screen on where you want to search. 2. Click Event Search. The Event Search text (red) would appear at the lower left corner of the screen. 3. In the Event Search Setting dialog box, check the type of condition you want to search. The video search would stop at the frame that matches the condition. To keep on searching click Find Next( ) button. 4. You may also set to search and list all the result.
iEnhance Chapter 5 The bundled iEnhance is a video editing tool and can only be used with *.dvr and *.avf video file. It allows you to adjust the video picture quality, segment and save the selected portion of the video, zoom in and out the image, and print or save the screen shot. You can also save the setting and apply it on other files. To run iEnhance application, click iEnhance button on USB Playback Console interface.
Name Function (14) Effects Gray Scale: convert the image into black and white (monochrome). Normalize: adjust the brightness intensity. Equalize: automatically adjust the images that are too dark. De-interlace: smooth out the overlying frames. - Static: de-interlace for motionless scene. - Dynamic: de-interlace for moving scene. (15) Picture Adjustment Adjust the Brightness, Contrast, Saturation, Hue and Gamma. (16) Original Screen Display the original state of the image.
Using the Remote Programs Chapter 6 User can use Microsoft Internet Explorer to access DVR system by entering the IP address. To use this feature, make sure that your PC and DVR server both are connected to the internet and the Network feature is enabled. Accessing this feature for the first time you will be prompted by your browser to install WebCamX.cab, allow the installation and you should be able to connect and login afterwards.
6.1 Familiarizing the Buttons in WebViewer Right-clicking on the WebViewer video screen, enables you to start video recording, change video quality, switch camera and enable/disable DirectDraw. i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (14) (13) (12) (11) (10) (9) (8) (1) (2) Name (4) (5) (6) (7) Function (1) DirectDraw i (3) Enhance the video quality. Not all graphic cards can support this function.
Name (14) Select cameras to view Function Select to the view camera from different server. In Select Camera dialog box, Display column, click to enable/disable viewing the camera. Click Add Server and select the server type between DVR and IP Cam to add. Click Delete Server to delete the selected item. Click Import to load the previous saved list. Click Export to save the list. Click Apply All to change all the camera video quality based on the selected setting. Click OK to exit.
6.1.1 To Setup Remote System Setting The setting here applies to Remote DVR only. 6.1.1.1 System Setting In the System Setting windows, click Update to accept the new settings, click Exit to exit without saving, and click Default to revert back to original factory setting. (4) (5) (1) (2) (3) (1) Delete recorded data after If you want the system to automatically erase the data after a certain days, enable the Delete recorded data after check box and enter the numbers of days in Days text box.
Enable the conditions in Login section you want the system to automatically carry out. - Auto record when login Automatically start video recording when the DVR is executed. - Auto start Network when login Automatically connect to network when the DVR is executed.
6.1.1.2 Camera Setting Select the camera from remote DVR servers to modify settings. In the Camera Setting windows, click Update to save and apply the new settings, click Exit to exit without saving. IP Camera Setting i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (1) Camera Icons Select the camera number you want to adjust the video setting. To select all the cameras, enable the ALL check box.
(5) IP Camera Information To setup IP camera and display current IP camera information. IP Setting: Click IP setting to add the IP camera. 1. 2. 3. 4. 5. 6. Click the radio button of Protocol to start setup IP camera. Select the Protocol, Model, Video Format, and Channel of the IP camera. Enter IP address and connecting port in IP Camera Site column. Also, user can enter URL of IP camera instead of IP address. If the IP camera has authority request, please enable Authentication and enter ID and Password.
Analog Camera Setting Select the camera from remote DVR servers to modify settings. In the Camera Setting windows, click Update to save and apply the new settings, click Exit to exit without saving. i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (6) (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera.
Remote DVR Camera Setting Select the camera to modify settings. In the Camera Setting windows, click Update to save and apply the new settings, click Exit to exit without saving. i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera.
Enter the user id that for connecting authority - Password Enter the password that is for connecting authority - Channel Select the channel of connected camera 6.1.1.3 Record Setting In the Recording setup windows, click OK to accept the new settings, click Exit to exit without saving, and click Default to revert back to original factory setting. Record Setting of IP Camera i EH5108/EH5108H/EXR5008 series only has 8 channels will be available.
Record the video from the selected camera and save it to the designated storage path - Motion Recording Start recording the video from the selected camera only when the system detects movement. Once a motion is detected, the system automatically saves the previous frames and stop based on the Start Record Prior and Stop Record After settings.
Record Setting of Analog Camera i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (6) (7) (1) Camera Icons Select the camera number you want to set the recording setting. To select all the cameras, enable the ALL check box. To select more than one camera, Right click on the camera icon. To select one camera only, Left click on the camera icon. The camera icon turns purple when it is selected.
Stop Record After settings. - Smart Recording Automatically switch to recorded at the maximum frame rate setting once a motion is detected and if there is no motion, it records at the minimum frame rate setting. - No Recording The system won’t do any recording. (3) Motion Detection Adjust the sensitivity of the motion detection. The higher the value, the finer the sensitivity is detected. When it detects a motion, a green triangle mark would appear at the upper left corner of the screen.
6.1.1.2 Network Setting In the Network Setting dialog box, click Update to accept the new settings, click Exit to exit without saving, and click Default to revert back to original factory setting. For the network service ports that use by DVR server, please see Appendix A. (1) (2) (3) (4) (1) Server Name Assign a name for the DVR unit. Alphabet letters and numbers only.
- Network Bandwidth Limit By Channel: Set the network bandwidth by each channel. All: Set the total network bandwidth consumption limit.
6.1.1.3 Alarm Setting In the Alarm Setting dialog box, click Add to insert and set new alarm setting, click Delete to remove the selected alarm setting, click Update to save the setting, Exit to exit without saving, and Default to revert back to original factory setting. (1) (2) (8) (3) (4) (5) (6) (7) 1. Click Add to insert and set a new alarm setting. Click the items in the (8) Alarm Setting List if you want to modify the alarm setting. 2. In (1) No.
6. In (5) Sensor, select and click on the sensor number to set the condition for the system to alarm. If the sensor normal status is high, set the sensor condition to low. - Enable/disable the Abnormal Event check box, to set the condition of the event for system to alarm. Reboot: when the DVR system reboot without abnormal condition, the system will send out the alarm message. Abnormal Reboot: when the DVR system reboot in irregular condition, the system will send out the alarm message.
- Relay Output Set to enable/disable the relay operation when the alarm is activated and to extend additional time in second before it stops the relay operation. 1. Beside the Relay Output check box, click Detail. 2. In the Alarm Relay dialog box, select from the available relay list and in the ON column, set to enable/disable the relay operation when the alarm is activated. 3. In the Retrieve time check box, you may enable/disable to extend the relay operation time and set the duration in second. 4.
- Start Recording Record the video from the selected camera. i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. Beside the Start Recording check box, click Detail. 1. In the Alarm Recording Setting dialog box, select the camera to enable/disable video recording. Enable All to select all cameras. 2. In the Frame Rate selection, select As Setting to record the number of frames based on the Recording Setting. 3.
6.2 Familiarizing the Buttons in WebViewer PTZ (1) (2) (3) (4) (5) (6) Name Function (1) Direction buttons (2) Zoom +/(3) Select PTZ Adjust and position the focal point of the PTZ camera. Click the center to pan automatically. Zoom in and out the image. Choose to enable/disable the PTZ camera. In the Select PTZ dialog box, Select column, click to enable/disable viewing and controlling the PTZ camera. Click OK to exit and save the setting and Cancel to exit without saving the setting.
6.3 Familiarizing the Buttons in Remote Console (16) (15) (14) (13) (12) (1) (11) (10) (2) (3) Name (1) DirectDraw i (4) (5) (6) (7) (8) (9) Function Enhance the video quality. Direct Draw function supports for certain VGA card. For more information, please contact your VGA card vendor. (2) Exit Close the Remote Console. (3) Audio button Enable/disable the sound.
6.3.1 To Setup Remote Console Setting Click Setup button to call out the System Setting windows. Click OK to exit and save the setting and Cancel to exit without saving the setting. (1) (2) (3) (4) (1) Storage Path Set the directory on where to save the data. When there is not enough free space to record one hour data, the system automatically replaces the oldest data. In case you have more than one storage path, the system automatically saves the data to the next storage path.
6.3.2 Familiarizing the Buttons in PTZ Camera Controller (5) (4) (3) (2) (1) (6) (10) (7) (8) (9) Name Function (1) Close (2) Setup (3) AutoPan Exit PTZ camera controller. Configure PTZ cameras. Operate the PTZ cameras automatically based on the selected camera group preset position number. Adjust the focus manually to produce clear image. Zoom in and out the image. Adjust and position the focal point of the PTZ camera. Display the PTZ camera number that is being operated.
6.4 Using the Remote Playback To use this feature, first you need to select the source of the file. In the Select Playback Mode dialog box, choose Local Playback to open the file that is recorded in the Remote Console, and Remote Playback to open the file that is recorded in the DVR server. When you choose Remote Playback, select RealTime Playback if your internet bandwidth is fast and big enough, otherwise choose Download and Playback. Click OK to proceed and Cancel to void this operation.
video thumbnails. In the Time Selection screen, click on the video thumbnail you want to download (see also Chapter 6.4.3). 6.4.1 Familiarizing the Buttons in Local Playback Name Function (1) Exit To close the application (2) Split Screen Mode Select from 6 different split screen type to playback the recorded video file of all the camera, or one camera over the other or alongside on a single screen. i - If there are only 8 cameras, you won’t be able to switch to 13 and 16 split screen mode.
Name Function (5) Playback Control Buttons Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slower: Play the recorded video file at the speed of 1/2x, 1/4x, 1/8x, 1/16x, or 1/32x. Rewind: Wind back the video file. Pause: Briefly stop playing the recorded video file. Play: Play the recorded video file. Faster: Play the recorded video file at the speed of 2x, 4x, 8x, 16x or 32x. Next: Go to the next frame. End: Go to the end of the video file.
7. 8. 9. To adjust Video Quality if needed. And, select the Optimize for speed for faster file opened. For saving storage, select Optimize for storage. Click Save to save the video segment. 6.4.2 Familiarizing the Buttons in RealTime Playback Name Function (1) Exit (2) Split Screen Mode To close the application Select from 6 different split screen type to playback the recorded video file of the entire camera, or one camera.
Name Function (5) Playback Control Buttons Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slower: Play the recorded video file at the speed of 1/2x, 1/4x, 1/8x, 1/16x, or 1/32x. Rewind: Wind back the recorded video file. Pause: Briefly stop playing the recorded video file. Play: Play the recorded video file. Faster: Play the recorded video file at the speed of 2x, 4x, or 8x, 16x or 32x. Next: Go to the next frame.
6.4.3 Familiarizing the Buttons in Download and Playback Name Function (1) Exit (2) Progress bar To close the application. Show the progress of the file being played. You may move the bar to seek at any location of the track. Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slower: Play the recorded video file at the speed of 1/2x, 1/4x, or 1/8x. Rewind: Wind back the recorded video file. Pause: Briefly stop playing the recorded video file.
Using HandyViewer to Access DVR server Chapter 7 Users can use a mobile phone to access the DVR through Internet. Make sure your mobile phone support IE browser and is connected to the internet. To access the DVR server, open IE browser and enter http://enter server IP or domain name here/mobile. You can see the latest screen shot. Click << >> to change the channel or camera and Refresh to reload new screen shot. 7.
7.1.2 To Install PDAViewer from the Internet Make sure you are connected to the internet. 1. Open the web browser and enter the server IP. Then click the hyperlink Download PDAViewer. 2. When the Download dialog box appears, enable Open file after download and click Yes. 3. After the installation, the PDAViewer icon will appear in the Programs list.
7.1.3 To Use the PDAViewer 1. Run the PDAViewer on your PDA. 2. Familiarizing the PDAViewer buttons. Name (1) Connect (2) (1) (3) (4) (5) (10) (9) (8) (6) (7) Function Hook up to the DVR server. Make sure you are connected to internet. When the iView screen appears, click Add to add DVR server. Enter the server IP, port, user ID, password and select the connection type. Then, click OK. User can playback the recorded video from remote DVR server in PDAViewer.(see also Chapter 7.1.
3. To change the video quality, enable/disable audio, and select to display different camera, tap on the video screen longer the pop-up menu will appear. 7.1.4 1. 2. 3. 4. 5. 6. To Playback in PDAViewer Run the PDAViewer in the Programs. Hook up to the DVR server. Click Connect icon and select the DVR server Click Playback to enter playback option screen Select the camera, data, and time Click Playback to start playing the recorded video 7.
11. User can change the relay status.
7.2 Using JavaViewer to Access DVR Server Using the mobile phone within Symbian Smart Phone OS to access the DVR through Internet. Make sure your mobile phone supports Symbian Smart Phone OS and can be connected to the internet. To use this feature, you need to install the JAVA Viewer program that it can be downloading it from the DVR server through the internet. 7.2.1 To install JavaViewer from the DVR Server 1. Open the web browser and enter the DVR server IP (http://DVR server IP: port/JAVA-Viewer.
7. The JAVAViewer support PTZ control function, you can refer to Help file for detail function control key. Select menu and go the way down to select the Help file.
Using the Web Tools Chapter 8 The bundled Web Tools includes Dispatch Server, Remote Backup, and Remote Setup program. To install Web Tools, place the CD into the CD-ROM drive then click Install Web Tool. 8.1 Dispatch Server Dispatch is designed to reduce the network traffic of the DVR server. Instead of connecting directly to the DVR server, the client can connect to the computer that is connected to the DVR server using the Dispatch program. i 8.1.
8.2 Remote Setup Remote Setup is a tool for configuring DVR server from remote site. To install Remote Setup application, insert the Installation CD into CD-ROM drive and click Web Tools. After installation, click to start the Remote Setup application. 8.2.1 To Add DVR server User need to add a DVR server and make connection in order to setup remote DVR server. 1. Click Add 2.
setting and click Delete to remove the DVR server. 8. User also can import the setting by clicking Import button. To save the setting to local hard disk, click Export button. 8.2.2 To Setup Remote System Setting The setting here applies to Remote DVR only. 8.2.2.1 System Setting In the System Setting windows, click Update to accept the new settings, click Exit to exit without saving, and click Default to revert back to original factory setting.
Set the time gap of the Auto Scan function from 3 to 10 seconds. This automatically switches to the next video in cycle depending on the set time gap. (5) Login Enable the conditions in Login section you want the system to automatically carry out. - Auto record when login Automatically start video recording when the DVR is executed. - Auto start Network when login Automatically connect to network when the DVR is executed.
8.2.2.2 Camera Setting Select the camera from remote DVR servers to modify settings. In the Camera Setting windows, click Update to save and apply the new settings, click Exit to exit without saving. IP Camera Setting i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (1) Camera Icons Select the camera number you want to adjust the video setting. To select all the cameras, enable the ALL check box. To select more than one camera, Right click on the camera icon.
To setup IP camera and display current IP camera information. IP Setting: Click IP setting to add the IP camera. 1. 2. 3. 4. 5. 6. Click the radio button of Protocol to start setup IP camera. Select the Protocol, Model, Video Format, and Channel of the IP camera. Enter IP address and connecting port in IP Camera Site column. Also, user can enter URL of IP camera instead of IP address. If the IP camera has authority request, please enable Authentication and enter ID and Password.
Analog Camera Setting Select the camera from remote DVR servers to modify settings. In the Camera Setting windows, click Update to save and apply the new settings, click Exit to exit without saving. i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (6) (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera.
Remote DVR Camera Setting Select the camera to modify settings. In the Camera Setting windows, click Update to save and apply the new settings, click Exit to exit without saving. i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (1) Camera Icons Select the camera number you want to view. To enable/disable all cameras, click ALL check box. (2) Enable Set to enable/disable the selected camera.
- User ID Enter the user id that for connecting authority - Password Enter the password that is for connecting authority - Channel Select the channel of connected camera 8.2.2.3 Record Setting In the Recording setup windows, click OK to accept the new settings, click Exit to exit without saving, and click Default to revert back to original factory setting. Record Setting of IP Camera i EH5108/EH5108H/EXR5008 series only has 8 channels will be available.
The recording modes are listed below: - Always Recording Record the video from the selected camera and save it to the designated storage path - Motion Recording Start recording the video from the selected camera only when the system detects movement. Once a motion is detected, the system automatically saves the previous frames and stop based on the Start Record Prior and Stop Record After settings.
Record Setting of Analog Camera i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. (1) (2) (3) (4) (5) (6) (7) (1) Camera Icons Select the camera number you want to set the recording setting. To select all the cameras, enable the ALL check box. To select more than one camera, Right click on the camera icon. To select one camera only, Left click on the camera icon. The camera icon turns purple when it is selected.
and Stop Record After settings. - Smart Recording Automatically switch to recorded at the maximum frame rate setting once a motion is detected and if there is no motion, it records at the minimum frame rate setting. - No Recording The system won’t do any recording. (3) Motion Detection Adjust the sensitivity of the motion detection. The higher the value, the finer the sensitivity is detected. When it detects a motion, a green triangle mark would appear at the upper left corner of the screen.
8.2.2.4 Network Setting In the Network Setting dialog box, click Update to accept the new settings, click Exit to exit without saving, and click Default to revert back to original factory setting. For the network service ports that use by DVR server, please see Appendix A. (1) (2) (3) (4) (1) Server Name Assign a name for the DVR unit. Alphabet letters and numbers only.
- Network Bandwidth Limit By Channel: Set the network bandwidth by each channel. All: Set the total network bandwidth consumption limit.
8.2.2.5 Alarm Setting In the Alarm Setting dialog box, click Add to insert and set new alarm setting, click Delete to remove the selected alarm setting, click Update to save the setting, Exit to exit without saving, and Default to revert back to original factory setting. (1) (2) (8) (3) (4) (5) (6) (7) 1. Click Add to insert and set a new alarm setting. Click the items in the (8) Alarm Setting List if you want to modify the alarm setting. 2. In (1) No./Name/Description enter alarm name and description.
6. In (5) Sensor, select and click on the sensor number to set the condition for the system to alarm. If the sensor normal status is high, set the sensor condition to low. - Continue trigger duration: Set a time period that when sensor has been trigger and stay in the same status for that period, then the alarm will be sent out. - Enable/disable the Abnormal Event check box, to set the condition of the event for system to alarm.
- Relay Output Set to enable/disable the relay operation when the alarm is activated and to extend additional time in second before it stops the relay operation. 1. Beside the Relay Output check box, click Detail. 2. In the Alarm Relay dialog box, select from the available relay list and in the ON column, set to enable/disable the relay operation when the alarm is activated. 3. In the Retrieve time check box, you may enable/disable to extend the relay operation time and set the duration in second. 4.
- Start Recording Record the video from the selected camera. i EH5108/EH5108H/EXR5008 series only has 8 channels will be available. 1. Beside the Start Recording check box, click Detail. 2. In the Alarm Recording Setting dialog box, select the camera to enable/disable video recording. Enable All to select all cameras. 3. In the Frame Rate selection, select As Setting to record the number of frames based on the Recording Setting. 4.
8.3 Remote Backup Remote Backup is purely for backing up the *.dvr file from the DVR sever. You can select between Auto Backup and Manual Backup. Auto Backup continuously archives one hour of the recorded data at a time, starting from the specified date. As for Manual Backup, it only archives the recorded data of selected date. i To back up the data, you must have at least 2G hard disk space. 8.3.1 To back up the recoded data from the DVR server: 1. Make sure you are connected to the internet. 2.
- Click Schedule to select/unselect the time you want to backup. The red block turns white when it is unselected. - Enable/disable Disk Recycle check box, to automatically overwrite the oldest file when there is not enough free space to backup the file. Manual Backup mode: the backup progress will start when user press the backup button - Click File Select to choose the date, time and camera you want to back up. - Click Browse to set the storage path. 6. Click OK to complete the adding DVR server.
8. For manually backup, click file select button and select the DVR to backup.
Appendix A Registering Domain Name DDNS (Dynamic Domain Name Service) is a data query service mainly used on the Internet for translating domain names into Internet addresses. It allows remote clients to intelligently search dynamic servers without any previous enquiring for servers’ Internet addresses. In order to take advantage of this intelligent service, first register your domain name on the following Web site http://ddns.avers.com.tw 1. User Login Browse the website ddns.avers.com.
Appendix B Network Service Port The following table shows the ports that DVR server uses for certain network service.
Appendix C Using Functional Keys The DVR system provides shortcut keys. The table shows the function keys and descriptions.
WARRANTY NOTICE LIMITED WARRANTY AVerMedia INFORMATION, Inc.
